Counting matching models…
A beautiful flower vase for decorative purposes to hold artificial flowers. It is 170mm tall and 106mm wide. The photo shows the vase printed in vase mode. It can be printed in vase mode or printed in normal mode with 0 top layers and 0%…
Needed some washers, decided to make my own after some usual metric DIN standards. DIN 125 - Washer DIN 9021 - Big Washer DIN 6796 - Load washer
Approximately 700mm long model of the MZKT launcher. The model has 8 axles of which the first two are steering and the last 3 are steering on the opposite side, on the back there is the rotation control system. The silo can be held in a…
About model My custom design of Loudspeeker trim (front door) for Volkswagen T4. Made for a friend's Multivan, because I didn't like an already available multipart cover with need of glueing on Thingiverse. Compatibility For T4 Multivan /…
Found over at the 3D Warehouse good luck Dino93
PLA is ok, I would recommend ABS because it has some flex. 0,2 mm Resolution 40 % Infill Tree-Support
This model is compatible with the lego system.
This model is compatible with the lego system.
ball diameter 12 mm with bevelled bottom
My attempt was to make this M79 model realistic as possible so you could used it for Vietnam war events or as just a nice pice to your collection. Model has realistic manufacturer markings and imitation of the cocking mechanism under the…
This model is compatible with the lego system.
The length on the label is to scale, otherwise it is cut in the middle. The shaft diameter and head are not to scale as this look awkward on the small labels. I sticked with the text style of the original labels by the user @Pred_457770 .
Harmonic Drive for Keen-One EQ This is a variant with finer teeth (module 0.5) and can be printed without supports. The CircularSpline has 160T, the FlexSpline has 158T. The gear ratio is 79:1 With the 17HS15-1684S-PG27 from OMC…
This model is compatible with the lego system.
These are various styles of projectiles that fit in Adam-M's Catapult Card https://www.printables.com/model/211679-catapult-card . I printed the catapult in PETG, but didn't have anything to shoot in it, so I made these to fit nicely in…
My first model using forms in Fusion 365 - Slowpoke! This is also my first entry into the Sleepy Slowpokes Design Group - You should join cause this website can be lonely sometimes. The print is kinda straightforward, but assembly may be…
This model is compatible with the lego system.
*** Thanks for checking out this model! *** If you appreciate what I'm doing, consider buying me a coffee , and check out my other models for something else you might like! ********** [UPDATE Aug 27, 2024] Added a version of the tensioner…
Collection of screws (ISO 10642 / DIN 7991) including : M3x 5, 6, 8, 10, 12, 16, 20, 22, 25, 30 For general purposes PETG, PLA works ok. For some demanding application I would choose tougher material. If the fit is too tight, I would…
*** Thanks for checking out this model! *** If you appreciate what I'm doing, please consider buying me a coffee , and check out my other models ! ********** Looking for MORE upgrades for your enclosure? Consider doing this one! Original…
This model is compatible with the lego system.
KTM 790/890 Adventure chain slack tool! Slide in from the back on the chain buffer till it reaches the front upper chain guard mounting point. It might fit the KTM duke. 38mm is how tall the actual printed part is off the chain guide. If…
This model is compatible with the lego system.
Dyson Mini Turbo 967479-01 96747901 belt housing part T112750 supports needed This part was broken when the mini turbo brush of my Dyson V9 started to rattle I printed it in PLA and after a year it is still going strong Category:…
Printed in generic PETG at 0.2mm layer height without any supports, 5 perimeters, and 20 bottom solid layers. Write in the comments and post a make. Thank you and enjoy!
This model is compatible with the lego system.
This is standoff to mount the BTS7690 Driver Board with 4mm screw holes, mounting up and upside down possible If you want to mount it upside down, put the connection pins in the spot where the support beam is missing.
Collection of screws (ISO 10642 / DIN 7991) including : M5x 6, 8, 10, 12, 16, 20, 22, 25, 30, 35, 40, 45, 50 For general purposes PETG, PLA works ok. For some demanding application I would choose tougher material. If the fit is too tight,…
This model is compatible with the lego system.
We created a differential swerve drive for our 2022-23 Power Play robot. This is the pod design we created for our robot. The differential swerve pod was designed to be mounted to a drivetrain using 40mm needle bearings and a 1/4" Hex Cap…
I really don't like dust flying around my garage, routing edges was always one of the worst offenders. This shroud, combined with the standard dust collection port for DeWalt trim routers, will nearly eliminate stray dust from edge…
Collection of screws (ISO 10642 / DIN 7991) including : M4x 6, 8, 10, 12, 16, 20, 22, 25, 30, 35, 40 For general purposes PETG, PLA works ok. For some demanding application I would choose tougher material. If the fit is too tight, I would…
HR 8799 is the first extrasolar star system observed with direct imaging. Here you can find a time-lapsed video of 12 years of W.M. Keck Observatory (Hawaii) imagery of star system HR 8799 :…
Adapts DWS779 miter saw dust port to a 2.5" shop vac Prints ok without supports. The fit on the saw is a tight friction fit to keep it on without any extra support. May also fit other dewalt saws with 42mm outer diameter dust port
este es un soporte para w702 de carpuride para montar la pantalla
Tool to help check chain tension and wear as instructed in the KTM 790/890 Adventure owners manual. The extruded side is 3.5mm thick (middle of the acceptable range 2-5mm) and 25mm wide. The bottom is grooved to check chain wear and…
VESA adapter for Samsung C34F791 Needed two VESA adapters for my Samsung C34F791's The original parts are 55 Euro and either discontinued or “out of stock”. Made this so i could mount my screens. It fits VESA 100mm x 100mm. Printed with…
Simple tray for Philips Multigroom 7940 that you can change intro travel box or case. You can print whole thing without supports - the only think you can add them is the edge of the snap lock on top cover (support will make dimensions…
In celebration of the 40th Anniversary of ALIEN. I bring you a 1:1 scale Incinerator Unit Model Kit that I crafted in Fusion 360 resembling the unit from the film. (I have always wanted one!) "I am still improving this kit, so some parts…
30-40% infill is recommended. Bump up to 4 perimeters as well to fill the walls. Organic supports does make it easier to remove, but regular grid works fine as well. A remix of a model uploaded by Pavel Mironov on Thingiverse. The…
This model is compatible with the lego system.
This model is compatible with the lego system.
Organizer / holder for 5 Piece 3/8 Drive Socket Extension Set Harbor Freight 67926 In my quest for Toolbox organization, my socket extensions were next. I designed this tray to hold the Harbor Freight 67926 3/8 drive impact extension set…
This model is compatible with the lego system.
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
Disclaimer: This is not an official LEGO product. All design rights, trademarks, and intellectual property belong to the LEGO Group. This model is a fan-made recreation of the LEGO 40079 Mini Volkswagen T1 Camper Bus (Polybag) set,…
Esta impreso en pla gris sin soportes en 0.2 con roscas de 4mm, los vastagos son de ½ pulgada, se pueden conseguir en amortiguadores de autos.
Food Safety, PLA is generally considered to be food safe. Double check to make sure you are using non-toxic materials for any prints you intended to use with food. I am not a baker and getting the perfect consistency of dough to work with…
1979 Chevrolet Camaro & 1979 Pontiac Firebird — two icons from the same era. Two closely related American muscle cars, reduced to small, clean objects that keep their distinctive shapes and character. The Mini Cars DUO series brings…
This model is compatible with the lego system.
This model is compatible with the lego system.
Printed in TPU/FLEX Tire 43.2 x 28 S Balloon Small : Part 6579 | BrickLink Wheel 43.2 x 28 Balloon Small with Axle Hole (+ Shape) : Part 6580a | BrickLink
About model My custom design of armrest plug for front seats in Volkswagen T4. Made for a friend's Multivan. Compatibility For T4 Multivan / Caravelle / California. Model year: 1996 to 2003. Diameter: 35 mm Modifications I optimised…
This model is compatible with the lego system.
I changed the design of the motor mount to place the motor higher. Had to adjust the springs because of the weight of the motor. Had to move them outside the house and created two pieces to fit them. Created an optional cap for the motor.…
Simple wall mount for a Govee H5179 sensor. Flat back with screw hole for a fastener or use with a command strip or some double sided tape.
Esta pieza es compatible con lego.
Here is the CAD of the drivetrain that we used during the FIRST Tech Challenge 2022-23 Power Play season. It is a four pod differential swerve drive that utilizes swerve pods that we designed and released here:…
This model is compatible with the lego system.
Stanley FatMax FMST1-75779 Shallow Organizer Dividers for the large and small bins I used a 0.2mm layer height with a 0.4mm nozzle and printed in PLA Included is the f3d file A lid exists, to prevent small washers to move to another bin.…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
Created in Autodesk Maya as my scanner does not work on smaller than 100mm*100mm*100mm
My kids lost their lego. So I drew them a new one in f360. I also included a step. file if anyone wants to correct the tolerances. Print in PETG
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
Collection of screws (ISO 10642 / DIN 7991) including : M6x 6, 8, 10, 12, 16, 20, 22, 25, 30, 35, 40, 45, 50, 55, 60 For general purposes PETG, PLA works ok. For some demanding application I would choose tougher material. If the fit is…
UFO from the French film Le Gendarme et les extra-terrestres / The Troops & Aliens / Četník a mimozemšťané (1979). The model is composed of three parts. You can insert an LED candle inside the model or you can use glue to join parts. I…
Bruder Front axle for John Deere 7930 If you like it, press like it ;-) After only the axis was broken, i designed it to be printed. Therefore you need not to buy the parts which are not broken, rims, tires and so on 🙂 Fits to the Bruder…
This model is compatible with the lego system.
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
This is a parametric model of a circlip or retaining clip (DIN 6799 E Type External Circlip). It can easily be adapted to your use case by altering the parameters in the Fusion360 file. Just swap out inner (D2) and outer (D3) diameter and…
I adapted the original for the red MN82 (without S) for the model with rear bodywork MN82 S. The body of the “S”-Variant has different dimensions, so the original did not fit. I have uploaded two versions. The version shown has a 20°…
please follow us on instagram & tag us if you printed it: https://www.instagram.com/3dprintkings Print Settings Notes: I recommend to do a color change by script at height 3.5mm and use a prime pillar Category: Keychains
This is a M36 threaded bolt. You can scale it to the size you need: 133,3% – M48 116,7% – M42 100% – M36 83,3% – M30 66,7% – M24 55,6% – M20 44,4% – M16
Collection of screws (ISO 10642 / DIN 7991) including : M8x 8, 10, 12, 16, 20, 22, 25, 30, 35, 40, 45, 50, 55, 60, 65, 70, 75, 80 For general purposes PETG, PLA works ok. For some demanding application I would choose tougher material. If…
Use this piece to replace the original watch charging holder for the Anker A2579 and allow it to charge the Pixel Watch.
This model is compatible with the lego system.
License plate holder for the KTM Duke 790. This design uses the stock tail light and aftermarket 10mm turn signals. Most 3rd party tidy tails use a non standard tail light and many of them are bad. I decided to design my own tidy tail…
The original part is made out of PA6 GF15 but feel free to test possible alternatives. I would use at least PETG or ASA.
I am CAD Kim, the manager of the DCinside Minipc Gallery, a leading mini PC community in South Korea. You can find my channel here : Kim_CAD on YouTube . This is a full case replacement Mod Kit for the MINI PC called GenMachine. It is a…
You will need at least 3 filament colors Tree supports recommended No screws are needed; only a little of you choice of glue Most parts friction fit together
This model is compatible with the lego system.
This model is compatible with the lego system.
Its a water pump for an Motor 775 / 795 / 895. I printed it in PETG but i think you can use PLA as well. Fits tubes with an inner diameter of 20mm. You need: 8x M5 screw with min. 14mm(max. 32mm) DIN912 8x M5 nut DIN 934 or DIN985 2x M5…
This model is compatible with the lego system.
LEGO PART 79389 Bracket 1 x 1 - 1 x 2
I made this for the Worx landroid WG790 series, because the bearings on the originals were busted, and the wheel got destroide when i tried to remove them. Print instructions Category: Outdoor & Garden Summary I made this for the Worx…
Yamaha FS1 (mod 378) 1973 - 1979 scale 1:8All axes = PLA 1.75mm Velg only: without support Supports: Yes Resolution: Dynamic Infill: 50% line Filament brand: 195 - 220 Filament material: PLA
A holder for the DeWalt DCD796 drill/driver. To be mounted below a shelf. Holds the drill snug and safe, even with the big 5 AH batteries. Mounts with two screws to avoid turning. The reason for the 10 cm wide to is to make sure the wide…
A giant version of the controversial McDonalds coffee stirrer. Prints in 6 parts + pins. Includes all parts, with pins and instructions. Happy to answer any questions you may have.
Update 5/29/2025 I made a slight tweak to the model that reduced the floor of surrounding area around the tool. I lowered it to save on material, reduce overall print time, and make it easier to get it out of the bin. I've kept the…
I created rails for the Traxxas Utility Trailer #9795 which fit relatively tight into the Trailer and can be taken off if need be.
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
I could not find a hose connector on this site for a specific Shop-Vac hose size and Dewalt Miter Saw Dust collector, so I made one! First model, lets GO! I have the shop-vac hose of 1-7/8" inner dimension at 1.76" for a little more space…
This model is compatible with the lego system.
This model is compatible with the lego system.
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
Honda MT50 year 1979 Spoke rim only: without support Supports: Yes Resolution: Dynamic Infill: 50% line Filament brand: 195 - 220 Filament material: PLA
I wanted to mount a 140mm fan to my BD770i for additional air flow. However, the included bracket only allows for mounting of a 120mm fan. This mount allows a 140mm fan to be mounted offset to the I/O shield and bolts into the existing…
⚙ RECOMMENDED 3D PRINT SETTINGS Material: PLA or PLA+ recommended Layer Height: 0.16 mm for finer detail; 0.20 mm for faster prints Infill: 10–15% recommended for most models Wall Loops: 2–3 Supports: Enable where necessary based on model…
This is M793 printable tip to insert into real 25mm bushmaster (Bradley M2 IFV) ammo casing
![#0179 [UPDATED] Automatic Paracord Tensioner for Clotheslines [spring loaded, for 4mm cord]](https://media.printables.com/media/prints/962702/images/7581598_122262e0-2234-49ee-be2c-d0307a9276db_a2d9492a-091a-48f9-9736-3e0258748626/rl-20240819-011.jpg)
