Counting matching models…
This little piece slides into the flash socket on the Sony A6000 or A6500 cameras to hold the flash so it points up as shown in the photo. This allows the flash to bounce off the ceiling instead of hitting the subject directly. A bounced…
Print approx. €0.07–€0.09 excl. taxPreliminary estimate for one variant
Thumb grip for the Sony A6500 camera that mounts to the hot shoe. Works great if you have larger hands, especially when paired with the SmallRig. After accidentally pressing buttons with my thumb while shooting, I started searching for a…
a6700 Users - The Grip does not fit because of the reworked mode-switcher, use the following remix by @shoyler_79369 (UNTESTED) : Extended Grip Printing instructions: Use supports when printing the model, otherwise you will not be able to…
the og model was corupted and wasnt the best quality and didnt fully lock into place. this model fixes everything re modeled from the ground up
Extended version of a hot shoe grip for a6000 series cameras. This allows for some access to mode knob while not interfering with the standard Sony eye piece cover. Pictures show how the model fits on an a6600 and an a6300.
There's a few thumb grips available for this camera, given that it's quite compact and streamlined (completely unergonomic), but none of them quite do what I want. So I made my own. Most of them get in the way of the mode dial. This one…
For building your own Mega65, refer to https://c65gs.blogspot.com/ or to Chapter 12 of the Mega 65 Book, available at https://files.mega65.org/manuals-upload/mega65-book.pdf The model is intended to be used with M3 threaded inserts.…
These are printable brackets for the Openmower Mowgli version to hold the Raspberry Pi, Ardusimple RTK receiver For NX100i, SA650 and similar models Model still needs some tweaking, STEP included
"Anti klapper" Hörmuschel für Panasonic KX-TGA651EX ist für Hörgeräteträger entwickelt die akustisch durch den mechanischen Kontakt des Telefons am Hörgerät und den daraus entstehenden Stör/klapper/raschel und Stoß-Geräuschen gestört…
Combine 65W charger with 6000mAh power bank back to back. 酷科 65W 饼干 + 6000mAh 移动电源背靠背。
This clip-on tool-less attachment adds a cold shoe fitting over the top of the hot shoe, leaving the rear of the hot shoe open for the thumb grips that are acquired for cheap online. I designed it for an extra sight, but would also work…
Sick of dealing with tangled cables when using your Dell charger? Does your charger cable constantly unravel in your bag, creating a mess? This 3D-printed cable organizer is designed specifically for Dell power adapters, allowing you to…
This 3D-printable speaker mount allows a Quadra 650 speaker to be installed in a Quadra 700 when using a 650 logic board. This model was created by Kero's Mac Mods team, Alan Williams under the supervision of Kay Koba . The mount is…
This ignition coil adapter can be used to mount a standard Honda/Kawasaki/Suzuki/Yamaha ignition coil on the original mounts of a 1968 BSA A65. The ignition coil will be placed tight at the frame so that it can be fully covered by the…
I needed an offset mount to set my Sony a6500 back on the top of the Vivo monitor tube, so the monitors could angle inward closer. It's designed to be printed as it come into your slicer, with the recesses facing upward. No supports are…
This adapter replaces the original built in Fantasea Adapter for mounting LEDs of a Turtle TTL trigger. Without this adapter only one LED can be mounted without mechanical conflicts. Mounting: Remove the small black plate - it's attached…
This little piece slides into the flash socket on the Sony A6000 or A6500 cameras to hold the flash so it points up as shown in the photo. This allows the flash to bounce off the ceiling instead of hitting the subject directly. A bounced…
Print approx. €0.07–€0.09 excl. taxPreliminary estimate for one variant
Lost the proprietary hot shoe cover for your vintage Sony Alpha camera? This is a 3D-printable replacement cap designed specifically for the unique Sony/Minolta Auto-Lock Accessory Shoe (iISO). It slides perfectly into place to protect…
I re-spun the nexys4 case a bit. I added built in reset buttons that print in place at one go. I also changed the power button a little bit. I find it to be less fiddly than the original one. I've lost the stl to that power switch but…
Copied from Thingiverse: I have a WORX 20V GT 2.0 STRING TRIMMER / EDGER / MINI-MOWER. I was fed-up paying for replacing the spool holding cap, so I have made my own. This replaces part WA6531 from WORX and I have used ABS. Enjoy
