Counting matching models…
Ventilation grille for a wall mounted hot air exhaust with 120 mm diameter. You can print the cutout template to get the correct hole size with a Dremel.
Print approx. €4.14–€5.06 excl. taxPreliminary estimate for PETGSource material: PET
First model ive uploaded, probably the 3rd ive ever made. Not a cad pro, so please forgive me. I based this off a picture from amazon, using eyesight and a bit of maths. Both of which arent so good, so if its a little inaccurate i do…
lost your cap while refilling your car aircon? just print one. This is the M8x1 R134a System Cap, 13 mm. Downside: The thread is along the layer lines but as there ist no pressure and just a dust cap it'll work.
I have an airco with a 150mm exhaust hose and a 100mm “plug” to connect it to the window. A made a simple adapter to connect en 150mm hose to a 100 hose. step file included so you can change it if you want to. I printed them at 0.36 on a…
Phone holder with sphere console mount for Dacia (tested in Dokker, should be similar for Logan and Sandero). Printed from PETG on Prusa Mini + as three part kit. Top cover is glued to two bottom mounts. Foam stripe is added between…
Exhaust vent adapter for portable air conditioner, desgined around a "click CPAC1907-C" but should fit any unit with an outlet of 110x140mm and 3mm thick base. Suits a 100mm duct pipe
Combs to reshape the ac fins
This Product has been updated to fix an parameter Issue for the connetion point with the conditioner. I also add a little addon part to fix the gap in v4 for the design issue. This had only to be used tu update the Version v4! The new…
I needed a 90 degrees duct to connect my air conditioning duct (150mm) to my ventilation system (125mm), without the use of excessive amounts of duct tape It fits on a mks3s+ build plate, well it kind of fits. :D I suggest you split it up…
I've had this aging (but fully working) Aircon unit in the garage for a while, the interface for the hose split and was unable to source a replacement so I've finally got round to designing a replacement. I've yet to fully print this (20+…
The cover and hose ring to add an intake hose. Only fits model EXP35U538CW!!!
This is the exhaust fan for the Royal sovereign ARP-9009TL model, if you have any questions leave a comment.
I found a nice video on YT about a polycarbonate panel with a drilled hole for any 15 cm air exhaust. The missing thing were the parts to connect the hose with the panel. So there they are, modeled from scratch. I used the sliding…
This screw clip is designed to attach a sheet of plastic / perspex / plexiglass / wood to your window, so you can most efficiently use a portable A/C unit. Works with: -35 - 60 mm thick window frames Instructions: -backer nut may not be…
If you have a window vent like mine this box will let you attach the flex hose exhaust of your mobile air-conditioning unit to it. As the part is symmetrical you can print two, one as-is and one mirrored, and attach them together to form…
I lost the adapter of my airconditioner thats connects the hose to the outside with the device to get the hot air outside. So I quickly designed one, it's not beautiful but it does the job Category: Replacement Parts
Wall-mounted AC remote holder with a 22x62 mm slot, suitable for most AC and TV remotes. Attaches with screws or double-sided tape. You can download the file and edit the dimensions using fusion or scale it up to your needs :)
3D Printable AC Drain Pipe Elbow Connector Keep your AC running smoothly and leak-free with this durable, 3D-printed replacement drain pipe elbow connector. Designed specifically for optimal water flow and longevity, this model is a quick…
Pretty simple.. Printed on a Mk4. Fits the collapsable 150mm ducting that seems to come with all such portable airconditioners. added a shell. Will glue it to my foam board ducting around the Condenser air intake. FYI, these hoses are…
Liked the idea of original model, but it was designed to be screwed in place. I needed to be able to disaassembly the mount on demand as it's a mobile airconditioner without any permanent wall hole. Inspired by the other remix source…
It was for a SunTec Portable Airconditioner. Inner diameter is 138mm but i can pressfit a 150mm tube inside it.
My take on a small table aircondition that uses water to cool down the air a few degreese. everything can be printed mostly without support. Only the tunnel need a little support in the hole for the container. Only the fan needs to be…
Are you like me and always use the timer on your aircon unit? Are you also always loosing the remote and spending a lot of time trying to find where you placed it? Well, here is something you will love! This remote holder has an opening…
You just need to drill 4 M4 holes in the plate with which you want to “close” your window. Then print the part and attach the outflow tube of the aircon with the adapter. You should be well prepared for the next heat wave- no matter if…
To replace the air vent and have a support for the telephone or other.
I recently bought a portable air conditioner (This model: https://www.amazon.co.uk/dp/B0CP42SSZD?psc=1&ref=ppx_yo2ov_dt_b_product_details ), and was having some trouble with keeping the exhaust air from coming back into the room. The unit…
My aircon monoblock has a square hose adapter for the hot air exhaust. In order to be able to move the aircon but leave the window adapters and hoses in place, I needed another adapter. Maybe this is something you need too :) I printed it…
Wall mount for the tube from iiglo IIAC12000W aircondition Mount the wall mount and screw in the pipe. Use organic tree support - print in PETG cause moist air … you know
can not be from PLA because air temperature is to high
Outlet for Aircondition tube with 150mm diameter. Has thread, so you can screw the tube on.
This model is a simple filter for your airconditioner condensate water pipe. For 16mm pipe! -0,4mm nozzle
Adapter at 25° angle for Howell mobile air conditioner exhaust duct. Needed to be able to connect it with lower part of the window in the way. Printed in PETG to withstand and maintain shape and strength under hot air exhaust.
AC adapter that allows the hot air from your electriQ (and others) to be expelled via the mailbox letterbox. I printed with tree organic supports in PTEG 35% infill.
Replacement corner intake grille for the Eurom Polar 16CH portable AC, with a 150mm hose collar built into the back face for external circulation or runoff. Every dimension traces to the physical unit: laser scan, hand calipers, five…
Portable aircons need a way to get rid of condensation water. This is usually done with a flexible hose draining outside through a window. This allows you to drain in a Gatorade bottle instead If your aircon has a 12 to 13mm outlet hose…
Louver to motor connecting part The motor opening is 3x5mm Total height is 16mm , length 17mm and depth 7mm Tested with ABS , fits perfectly
Portable aircons need a way to get rid of condensation water. This is usually done with a flexible hose draining outside through a window. This allows you to drain in a Gatorade bottle instead If your aircon has a 12 to 13mm outlet hose…
Wall mounted holder for Mitsubishi Remote. I used sticky pads to secure as i was unable to drill in to the wall.
A tiny window AC, good for dioramas but can use a TEC module Front takes 40mm fan + heatsink, rear takes another 40mm fan+heatsink Designed for a 30mm TEC IIRC (it has a 40x40mm space) sandwich fan+heatsink+TEC+heatsink+fan, push into the…
Mounting bracket for the power switch on an AirConception Delta Paramotor Frame The standard mounting location is over top of the left shoulder which is almost impossible to reach while wearing the ParaMotor. Includes hole for optional…
This vent is located below the HSI in the F-16. This is my print in place replica it should work right of your printer. Dimensions: There are two different screw dimensions those being 41.28*41.28mm and 42.66*42.66mm you should also have…
Mounting bracket for the power switch on an AirConception Delta Paramotor Frame The standard mounting location is over top of the left shoulder which is almost impossible to reach while wearing the ParaMotor. Includes hole for optional…
This is a holder for your Aircon remote or other similar sized remote. I designed for wall or cabinet mount with double sided tape. A flange on the rear ensures the mount sits flush against the surface with the tape invisible. The front…
Needed an adapter for my argo swan evo airconditon for my wall vent. Print in PETG, PLA will become too soft from the hot exhaust air. PETG with a heat deflection point of 71c seems to be holding strong. But I haven't had my AC on for…
It seems 130mm hoses for portable AC's are hard to find (in The Netherlands). Someone asked our company if we have the 130mm hoses. We don't. The man already bought a 125mm hose at the local hardware store but that didn't seem to fit. So…
Nissan Leaf Aircon Compressor Bracket for using the Leaf A/C pump in an EV Conversion. Two models are included. One includes threaded risers and could possibly be printed in an engineering material and used as is. I printed in PLA just…
This fits the portable aircon window attachment but I will be using this for my Yoopai 3D printer Enclosure. Just use glue to join the faces together or drill/create a hole for nuts and bolts. Printed using PLA on Anycubic kobra 2 Max.
Please leave a like and and consider posting a rating/make if you find this design useful! Use split to objects in the slicer to separate the screw cover. Not sure of the exact model of remote (I think it's the Daikin arc452A4), but if…
Files to print (3 parts): 1. custom-bushing-150mm.stl - Wall bushing with M4 countersunk screw holes 2. exhaust-hose-adapter-150mm.stl - Hose adapter (bayonet twist-lock) 3. lid-150mm.stl - Cover lid for when AC is not in use Print…
This is a connector for threaded 125mm aircon outlets and flanges to mount it all to a board which can be placed in the window frame as a seal. I printed it in white PLA but if this proves to not be heat resistent enough, I might have to…
This particular portable AC model is quite rare as it seems to be a Costco exclusive and whilst Meaco do have other 12k Pro portable models they all seem to slightly differ to this. There's very little information about this model online,…
Holds an Aircon Remote. One of ours was broken so designed this replacement. Openscad file is included if you need to adjust the dimensions for your remote. Needs support when printing. Print Settings Supports: Yes Category: Replacement…
I use my aircon unit daily in summer, but the problem is that I have to open the window a lot to be able to put the exhaust tube outside. To solve that, I made this adapter that smoothly transforms the round tube into a small rectangle…
I found that my previous version could be improved, so I designed a better one. It fits the tube more snugly and is a lot less wide, so your window is opened less. You can print it on 0.25 layer height and without supports. I also added…
UPDATE: Adapter for 120mm hose! I needed a adapter for the exhaust air hose of our aircondition, because we have insect mesh in front of our windows. So i decided to create this simple adapter which will be pushed between the window frame…
Could be used with this cabin style: https://www.printables.com/model/412034-tarra-trucks-cabin-with-slot-for-beacon This is just a part used in Tarra truck models. For full model kit please follow this collection:…
This three piece adapter set is designed to work with 100mm (4 inch) ventilation ducting. This allows you draw cool air from a window mounted Air Conditioning unit, transport it through a 2cm x 20cm gap and then back via 100mm round…
This adapter allows you to use potentiometer knobs Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 100 Infill: 100 Filament: PolyMaker PETG Category: Automotive
A simple replacement blade/vane for the swing function of a B&Q Cyclone 12000 BTU portable air conditioner unit. Replaces blades where the top/bottom or the ‘swing’ peg has broken off.
Aircon Remote Wall Holder for Daikin ARC452A4
You can push the pushfit rod into the case, maybe use some glue… I printed it with PETG (PLA should be fine also) 0.2 layer height 0.4 nozzle It could work also with Honeycomb storage wall via adapter . Credit Multiboard is designed by…
The installers failed to attach the cover plate to the bottom of the outdoor construction unit.
Please. Print test print to check for fitment before printning and painting all 4 knubs I recomend to use as low a layer hight as possible, to make the sanding less demanding and time consuming. i used 0.10 in layer hight PLA And support
Needed a simple aircon holder, to keep my desk free. I attached it to my bookstand attachment of my nitori desk. The 3mm wall thickness seem to be stable enough for also heavier remotes. Possible Dimensions for Remote: -Length: 59mm…
