96 models
3D MODEL DESCRIPTION My father needed a blade balancer for his lawnmower blade this summer, so I designed him one. How it works: If the blade is unbalanced, one of the edges will weigh further down than the other. Then you have to remove…
A starter for the urgent desires. So, com board is ready and was done with M3 heat inserts in mind. As there is currently no idea of where it would commonly fit this is not the final solution. I for my part will fit it into a gridfinity…
This is a remix to address some issues I had with the original design. Printing info: PLA 0.4mm nozzle 0.20mm layer height 15% infill [UPDATE 6/22/2026] Per request, here are the diameters for the steps on the original model as posted.…
Protective caps for Li-Po balancing connectors - JST-XH 2.5mm. Available sizes: 2S, 3S, 4S, 5S Additionally, more sizes can be made by editing the original STEP file (slicing in the middle and adding/subtracting 2.5mm). Please print a…
Simple RC Airplane Balancer. Help find the CG of any RC airplane. Enlarge for bigger airplanes. Print Settings Printer: Sidewinder X1 Rafts: No Supports: No Resolution: 200 Infill: 20 Category: R/C Vehicles
Thanks To SnappyFPV Just a Remix for 2s 3s 4s 5s & 6s JST-XH balance connectors. I didn't test them all please let me know if they work. Print Settings Printer: Craftbot Plus Rafts: No Supports: No Resolution: 0.2 Infill: 100 Category:…
These rod ends will help you make a very good balancing tool for accurately setting the CG of your plane. Works with most monoplanes. Biplanes and some high-wing planes may have special CG requirements. Printing and build tips: Print in…
This stand is very useful, when you charge / discharge your batteries. It provides you a better view in order to control parameters and measure values. Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: Yes Supports: Yes…
I wanted to have a blade balancer which fits a wide range of center hole diameters so that I can balance the blades of all different lawn mowers I have. In my opinion the balancing units one can buy are way too expensive so I came up with…
Designed for M8 nuts and 4x 608 bearings (8x22x7) and 8mm rod
A case for a well known active balancer board. I used melt-in threads, the board comes "upside down" because the parts that can get hot are on the other side. Make sure the cover is placed correctly over the transistors.
print at 101% size for easier fitting of the bearings and use 3mm screws and nuts to fix the foot
This should work with any vehicle that has adaptive cruise control but still requires your hand to be on the steering wheel (Not a Tessla, they figured a way around it :)). The common problem is that you will still get a warning to put…
PROPELLER BALANCER 2 x Stopper PA25 Slot.it 1 x Steel Pro axle Turned ground, polished, 2.38 mm (3/32”) x 54mm Slot.it Category: Props
Filament Balancer Switch The Filament Balancer Switch is an innovative sensor mechanism that accurately measures tension and compression on the filament during the printing process. This model stands out by utilizing two separate…
This is an antenna mount for the Kayoumini quad. It features holders for the RX antenna, the VTX antenna and storage for 2S balancer plug. Choose between 14 and 15 mm standoff height and 3.5 and 4.0 mm standoff diameter. Print with TPU in…
My version of the ever popular wine bottle balancer. Two versions, one with a corkscrew on the back and the other has a wine glass. EDIT: I found a problem with the corkscrew version and I reuploaded a corrected STL. Sorry! ALSO, It…
Simple balancer to check CG of RC planes :) Category: R/C Vehicles
I designed the front and rear holders to use the existing screw holes in the balancer PCB and to also cover all the electronics in the front and back. I just remixed my original model and removed all vertical mount features. I haven't…
Choose between single-piece or multiple-piece design. I recommend the multiple-piece design because you can print it laying on bed and thus get more precise dimensions of the bearing faces. You will need 8pcs of 3X10X4mm bearings (4pcs…
Use a 3mm carbon or metal rod Category: R/C Vehicles
This is a tool I Created with a few required parts… Some 5mm Carbon Fiber Rod or anything like it that you can cut 2 pieces from one is 20mm and the other about 130mm. 2 M3x4mm Threaded Heat Inserts 2 M3x14mm Screws 1 M3 Locknut Some m3…
I tweaked the bottom of the base of Materialistic_3D's Lawnmower Blade Balancer design ( https://www.printables.com/model/244656-lawnmower-blade-balancer ) to be printable without supports for printers that can handle 45º overhang. This…
I wanted to mount my NEEY Active Balancer vertically because it fits the direction of my installed batteries and their balancer cables. I designed the holders to use the existing screw holes in the balancer PCB and to also cover all the…
JST XH Replacement Connector for 3S & 4S Lipo Balancer Lead. Simple Version should be printable without Support
Designed it for my 8S LiFePo4 Active Balancer for my 24V LiFePo4 battery bank.
I designed this stand to hold my Hudy RC Tire Balancer. The balancer can be hand-held, but the stand makes balancing hands-free and eliminates human factor during the process. When not in use, it can be easily disassembled and stowed in…
Are you tired of your propellers constantly chewing your balancer cables? - Heres the solution. Three different sizes for 6S batteries. I recommend a layer height of 0.1 mm.
Radiomaster Zorro Neck Strap Balancer and GoPro Mount Designed to be secured with M4/M5 Screws and Nuts The screw in the photos is a M5x20mm (I don't have a shorter screw ATTOW) See the last image for the dimensions Print Settings…
Update 19 dec. 2025: I added a new version for the screw with increased tolerance of the thread, so that it can be screwed in more easily. This is a vise mounted device for balancing lawn mower blades. Thanks to the conical base of the…
Mit den Adaptern könnten die Balancer-Anschlüsse am Akku befestigt werden. Gedruckt am besten in TPU
I Designed simple Lawn Mower blade balancer. To create it you need only 2 berings 608, 1 screwe M4-55mm long 1 square nut M4, 4 magnets 6mmx2,6mm. Optionally 1more M4 nut & washer. Bu default you have central pin 10mm - suitable for Lawn…
Printed in TPU Used tree support Double-side silicon tape If you are wondering what that awesome drone is - 2.5" Kayouframes Kayoumini
Simple enclosure with holes for easy mounting. Print with something heat resistant, these can get hot when they are discharging batteries. There are two versions, one with honeycomb pattern and one that's fully closed.
CG Balancer for planes. I use raft just for the part #4. All others can be arranged such as no raft is needed, laying on the back. It is built for tube of 16mm diameter, the small is 6mm and the T shape is 15mmx15mm Category: R/C Vehicles
Check your local rules to see if balancing can be done, or if there are restrictions on how to balance (such as adding or removing mass). The fixture will require the following additional hardware: Qty 2 - M5 hex nut 16mm or longer M5…
Glue 2pc 8mm magnets and add a 6200 ball bearing in centrum. Place these over a 10mm drill and you can balance the lawn mower knife after sharpening. For lowest friction, clean the ball bearing with alcohol from all grease, and lubricate…
Device for the static balancing of motorcycle tires Vorrichtung zum statischen Wuchten von Motorradreifen Metal Parts: 1x Steel Plate 400x300x5mm 2x Stell Square(40x40) 760mm long 1x Stainless Steel Axel 10mm dick 40mm long Screws and…
Dimensions are not finished yet! It may or may not fit your wine bottles' neck :) Category: Decor
Nerf or other 2mm flywheel balancer Requires at least 2 5mm diameter strong magnets and a shaft out of an old burnt up 130 size motor
Case for a flying capacitor balancer for NCM/LFP batteries. PCB size is L66xW46xT16mm There are two versions of the body depending on the integration. 4x M3 Cyl. 20mm 8x M3 Washers 4x M3 Cyl. Enjoy.
This is my first model, it's a simple Washer to balance the missing Z height between the Buildplate and the Mounting Y Bracket, so that you can get the Same Amount of Pressure on all 4 Y-Screws
To prevent excessive wear and tear on the bearings in my rc-basher, I constructed these wheel-balancer. On top speed balanced wheels can calm down the car. I used a thread rods with three bearings from a skateboard or inline-skates. Two…
1. Introduction: After modifying the original design and creating V1, I discovered the base was bending and twisting in my vise when a blade was attached. Also, the pivot shaft was bending with a heavy blade attached. With these…
Longer version of the neck balancer for FS-i6 transmitter with larger hole.
This is for the Harbor Freight wheel balancer. Also known as a static or bubble balancer. I got this one from Amazon. Works well for car or truck tires after simple modifications but for trailer tires the springs that compress are too…
Remix of hegelklimbo 's original balancer that uses 608 bearings. See photos and original for assembly. Some changes I made: -Converted it to use 608 bearings & a M8 shaft. -Tightened up some tolerances. -Added some 8-32 set screw holes…
Just print as is and cut open the side, put the LiPo in and seal it back together with a soldering iron at 250°C. You can also water seal it with liquid tape on the opening for the cables. Print in soft TPU to be able to get the LiPo…
This is a scale model of a tire balancer, perfect for your scale pit or garage.
Make sure to choose the correct file for your type of battery. You need something to poke the pin out to remove the original pad and to reinstall it for the new one, I used the straight pick from a 2$ set from Harbor Freight. (Check the…
There are a couple of lipo balance plug savers already on Thingiverse, but I couldn't find any for 2S batteries. So I've designed my own customizable version. Print Settings Printer: Fabrikator Mini Rafts: No Supports: No Resolution:…
I’m entering the Balancing Games challenge with my very own twist on the classic pin support test! I designed a unique pin‑and‑ball model that pushes the limits of gravity and precision — can you stack it without tipping over? This…
5th Gen VFR800 adapters for balancing the rear tire. I designed this adapter to utilize a VFR800 axle to hold the rim on the balancer rod. The axle adapter is inserted into the chain side of the axle, this reduces the size of the hole for…
I like the basic design of this blade balancer. On my Prusa Mk3S, I chose to print the parts with PLA using 40% infill and at a 0.10 mm layer height for accuracy in the screw threads as well as for strength and appearance. No supports are…
This tray is for the OEMTOOLS 25053 Heavy Duty Harmonic Balancer Puller Set. Available on amazon here: https://a.co/d/6POoG9x
Designed for the Jumper T20S. You'll need a M3x12mm internal hex screw and a M3 nut for assembly. It's possibly a good idea to print from PETG or ASA.
I use this packs to power my goggles, because I don't like having loose cables hanging around to my battery in the pocket. The 2s5Ah battery lasts me one complete racing day and recharge takes around 3-5hrs, depending on your USB charger…
Decided to make this to reduce the chances of screws coming loose and flying around the 280ah diy house batteries in my skoolie. yes the balancer is potted but can never be too safe, right? initial print is 2 sidewalls, 2 top and 2 bottom…
This is a holder for the Neey Balancer. You need to print this model two times from flexible material like sainsmart TPU. It then clamps onto the M8 rods which hold together my battery pack. The recommended distance for the rods is 151.5mm.
Printing advice. All settings below are for Pruca Slicer Prusament PETG, 0.4mm HF nozzle Print settings: Body - layer height 0.25mm, structural, default settings but infill, which is cubic Holder - layer height 0.15, structural, default…
I found sometimes my lipo batteries, took longer to charge when the cells were not well balanced. The charger repeatedly puts power into both cells then drains some current out of the cell with a higher voltage to try and reduce the…
This is a balancer for multicopters such as S550, F550 and similars. You can use it when you need to balance the multicopter in order to center the gravity center for an optimal fly and obtain the máximum performance of the motors. Each…
Made for exactly this one: https://www.aliexpress.com/item/1005005204505095.html?spm=a2g0o.order_list.order_list_main.35.36ef1802NfpHzS but you can fit the stock one too. The whole box have the same outter size as the original one (only…
Simple Tray to hold the Du-Bro Prop Balancer with space to store prop nuts, props, and sharpie for marking props 7" props in pic Printed in PLA
Original design was a plastic pulley riding on a metal shaft. Upgraded to a sealed bearings (Amazon ASIN B0CSPBK6VL, Part MF85ZZ - 5mmx8mmx2.5mm), using a 5mm shaft. Also printed a couple of plastic shafts, but ordering plastic rod/tubing…
I've printed this with Elegoo PLA as it won't be around much heat. You'll need a few parts to complete this build. (Links have been provided) M3-0.5 x 8mm Button Head Screw x 4…
The Hole is for a Screw or a piece of Filament. PRINT it in PP Polypropylen Print Settings Printer Brand: VoronDesign Printer: Voron 0 Rafts: No Supports: No Resolution: 0.1-0.2 Filament: No NAME PP Category: R/C Vehicles
These are brackets that allow you to mount the Marc Parnes wheel balancer to wooden uprights. Not absolutely necessary but they do help the balancer from slipping off. There is some left right adjustment but try to get the spacing of you…
This is a case for the AOK 150W 3in1 discarger. I printed it in ABS because the bulbs get hot. http://bit.ly/3rh6Umn Print Settings Printer: Craftbot + Rafts: No Supports: No Resolution: 0.3 Infill: 25% Filament: No Name ABS Black…
A small block that turns 25mm diameter keyboard stand into model balancing tool.
I had a set of heavier wheels that were close to the cone size limit of my balancer and they didn't quite receive enough force to center on the cone well so I printed this spacer and it helped center the wheels easily. I printed it with…
A pair of bearing adapters to fit the Volkswagen Type 3 engine crank pulley for balancing purposes Category: Automotive
made this part for a company where the holder for rim's was often destroyed. This seemed to do the trick :) Category: Parts
A wine balancing system for those people that love to give uneven pours. Avoids that selfish pour. It works. Probably not as well as would have liked, but it works. Need to play a little on the infill to get the balance perfect. I used…
This balancer is meant to accommodate wheels with a 12mm hex (it has only been tested with 1/16 scale wheels). There is two variations: vise and base. The vise version is made to lock into a vise: And the other version has its own base…
Idk i was just trying to balance a bottle and thought, "Why not make a balancer myself?" Designed for those boxy carton bottles you often get for fruit juices
GWL.EU balancer holder https://shop.gwl.eu/Battery-Management/Cell-Balancing-Module-3-60V-1-7A-screws-cables.html Category: Electronics
This is a quick development of a neck strap balancer for the Devo 7E. I am sure people can use it for other radios. To print(I print with Repetier-Host): 1.Rotate the part to lay it flat (-90deg X-axis) Create a copy of the part. Mirror…
It's the weekend, every shop is closed, you've got a brand-new Vespa wheel to install... but it still needs balancing! This simple balancer is made with two 608ZZ bearings (Common Skateboard Bearings 8 mm ID, 22 mm OD), three 3 mm screws…
This DIY Center of Gravity scale is designed for balancing radio-controlled aircraft accurately. It features a microcontroller-based system using an Arduino Nano, paired with two load cells for precise weight measurement and an integrated…
This publish are few versions of balancer for Jumper T12 transmitter. Difference between objects is in length and in numbers of holes. For assembling I used shortened M4 screw and M4 nut. Category: R/C Vehicles
A simple cut out on a block to place on a small scale for cylindrical objects like arrows. I made this to place an arrow on my scale without it rolling around anymore. Place it on your scale then zero it to measure your object minus the…
Sick of loosing my expensive Prop Balancer shaft assemblies - I designed & printed this shaft storage mount that screws nicely into base spare holes. Original Rev 0 was higher, so reduced the height to allow the assembly to be flush with…
This simple RC plane CG balancer utilizes 3/4 schedule 40 PVC pipe as the vertical structure. The top contact bar caps provide a wide (~ 25mm) contact area to protect foam and other fragile materials. Print 2 of each and cut PVC the…
Key Design Features: Advanced Ergonomics: Features an integrated slide switch extension button with clear embossed position markings on the shell. Internal Anti-Skew Support: Specially designed internal alignment columns and stops support…
DE Beschreibung: Passend für das Tamiya CW-01 Chassis und warscheinlich auch CW-01E Chassis (Lunch Box und Midnight Pumpkin). Ideal wann man statt NiMH, LiPo Akkus nutzen möchte. Sorgt dafür das, das Balancerkabel des LiPo's dicht am…
Check your local rules to see if balancing can be done, or if there are restrictions on how to balance (such as adding or removing mass). The fixture will require the following additional hardware: Qty 2 - M5 hex nut 16mm or longer M5…
I had a set of heavier wheels that were close to the cone size limit of my balancer and they didn't quite receive enough force to center on the cone well so I printed this spacer and it helped center the wheels easily. I printed it with…
Simple enclosure with holes for easy mounting. Print with something heat resistant, these can get hot when they are discharging batteries. There are two versions, one with honeycomb pattern and one that's fully closed.
I've printed this with Elegoo PLA as it won't be around much heat. You'll need a few parts to complete this build. (Links have been provided) M3-0.5 x 8mm Button Head Screw x 4…
