Counting matching models…
Its a battery holder. Made by fafabienman from https://www.thingiverse.com/thing:3358129 I did not make the model I'm just show casing it. Print instructions I printed this in 0.3 layer height and no supports did a good job and pretty…
BOM: Printed with ROSA3D High Speed PLA Dark Blue This is the "Powerhouse" edition of my octagonal battery holder system. These 4-row wide grids are designed specifically for large-scale energy storage projects, such as home powerwalls,…
Replacement battery cover for DumboRC DDF-350 Transmitter.
This is a mockup of the TP4056 USB C Battery Charger Li-ion Module for further case designs sizes and dimensions have been measured carefully If this helped you, please leave a like! That's my reward and payment! 👍 I ll be happy to get…
Beside printed parts you will need: soldering iron electrical or kapton tape two 13400 li-ion cells (from disposable vapes) LX-LISC-V2 usb-c 2s li-ion charging board super glue Please don't buy your cells. Just pick them up from curbside…
Mount 3 Ryobi 18v batteries to wall control pegboard using the DDD Printable Wall Control System . Note: If you use the center piece to combine two of these together, the middle batteries will be rubbing together a bit. They fit, but it…
I had a side project needing a 20v source at a time when name brand chargers were unavailable except at scalper prices. The Elefly DCB112 solved the charging need very well for $20. But annoyingly and surprisingly it doesn't have a built…
As all the other battery holders did not seem to work for me I made my own. V1: has hooks to hold on to the frame. V2: slides ove the frame so won't pull off in a crash.
This 20V Dewalt battery connector includes an integrated over-discharge protection module that prevents the battery voltage from dropping too low. This protection circuit is rated up to 20amps and the cutoff voltage when the battery…
Dewalt 18V Battery to Dewalt 12V (NiMH) Skin ** you will be over volting your tool ** Extra requirements 2 x 6mm male spade connectors 2 x 6mm long male spade connectors 4 x M3 nuts 4 x M3 10mm socket head bolts 2 x wires 40mm long, 5mm…
Adapter: Bosch PRO Battery → TS10 Soldering Iron Mount (Press-Fit, No Glue) This adapter allows Bosch PRO batteries to be used with a TS10 soldering iron mount . The design intentionally avoids adhesives and instead relies on a tight…
Materiál: PLA Výška vrstvy: 0,2 mm Orientace: libovolná Podpora: žádná Výplň: 15 % trojůhelník
The case is for jufy111's 18650 holder. Here's the link: https://www.printables.com/model/999328-18650-battery-holder-case/files I designed it with snap off supports so that it can be printed diagonally for most stability. I do recommend…
A battery cover for Gameboy cartridges that have a rumble feature. These carts were notorious for the battery covers falling out. This design snaps in place securely by inserting the bottom two nubs into the notches on the cartridge, then…
3s 18650 Battery Tray for QX7 Print Settings Resolution: .12 Infill: 100 **Filament:** Overture PLA Notes: I used the metal battery tabs from the stock AA qx7 battery tray to make this 18650 holder. In order to use this tray for both…
A friend had a Dewalt job site radio that was missing the latch for the battery cover panel on the back. This one functions the same as the original. It was printed in PLA+ (which is supposed to be more durable than regular PLA, time will…
Hello all, this is my first uploaded make! This is a combo stand for carts and the accompanying battery device. For those pen style batteries that don't stand on their own to prevent the concentrate from lining the side. It was especially…
The Verathon Bladderscan BVI 3000 is using 6 cells NiMh 7.2V battery. It is expensive, hard to find, expensive to renew and moreover uses a proprietary charger which is brittle and often missing, super expensive on the second hand market.…
This is a holder for the Fingerbot to automate powering on the BK215 battery. Print with supports (due to the screws). PLA is fine, but PETG is better. Printable: 1 x Holder 1 x Leg extension Addition needs: • 1x Fingerbot (35 mm x 35 mm)…
Note that this model requires supports. print with the diamonds facing down and the holes for the batteries facing up. Once support material is removed there should be adequate space for nickel strips to be welded (in theory)
With this extended battery for the Lumix LX-15 camera you can shoot up to 6 hours! All models are available in both stl and 3mf formats, in the latter everything is placed in the bed in the best position for printing. Print settings:…
Simple Milwaukee M12 battery cap that allows battery to stand up securely on bench and with finger grooves for handling.
Modified the battery adapter from @Simon_220817 to have better contact of plus pole. Moved the battery 1mm to the front.
AA and C size batteries are the same length, but C is bigger diameter. In those cases you need a C size, this will help. Most rechargeable C batteries have the same capacity as a AA battery, so I use these for devices that need a C size…
A small tool to remove the AAAA-Battery of a Surface pen. If the pen has any dents or the battery inflated a bit this might help. Compatible pens It fits surface V4 pens which are the standard pen for: Surface Pro 3 to 7+ Surface Book 1…
Charged batteries have the positive pole facing up, empty batteries have the negative pole facing up. With this you can know the state of the each battery.
Battery Tray for Various Battery Types This 3D printable battery tray is designed to securely hold a variety of battery types, including: 14x AAA 9x CR2032 5x CR1632 5x LR44 2x 9V Block The tray is available in two file formats: STEP and…
Hide bright led when charge door is open. Can stay in place when door is closed.
This grip allows to attach battery for headlamp. Grip has been primarily targeted for this headlamp: https://www.kolo-park.cz/obchod/prislusenstvi-1/svetla-a-blikacky/predni-1/predni-svetlo-max1-power-led-20w-1500lm-detail…
All credit goes to theamzngq, and his models. I found that this stl had a pretty large gap between the base and battery post
A simple little set up to hold a battery and LEDs to make light up necklaces or other crafts involving button batteries. The 3-Volt 2032 button battery securely snaps into place and built in grooves guide the LED leads into place and hold…
A practical mount designed to securely hold standard 8x AA battery packs. The holder can be mounted using four screws for permanent installation. The design keeps your battery pack firmly in place while maintaining easy access for battery…
This is a minimalistic battery holder that i made. It holds 16 AA battery.
Parkside battery holder easy to print , follow my orientation to avoid supports , the model must be upright 50% infill , 0.2 quality , pla , petg and abs filaments are good Njoy Below is the link with all my designs…
A previous owner had cut out the battery bracket on my stupid little sports car to install an Odyssey PC680. When it came time to replace that battery, I opted to install a Yuasa YTX20HL-BS and drew up this bracket to replace the Odyssey…
I hate the idea of having different batteries for different tools or being locked into a tool brand because you've accumulated their batteries. Ryobi have some great 36V gear (40V in the USA) and I wanted to use my existing Ozito/Einhell…
This DeWalt battery holder is designed for convenient carrying of all batteries to the work site. It is versatile and prints easily, no support is needed, only two M4 screws with nuts from 12mm to 15mm in length are required. Print…
Battery door lever for the Olympus E-M5 III because it keeps breaking for everyone!! Remixed from @myxfit_28243 's model to fit the E-M5 III instead of E-M5 II Notches are raised by 0.5 mm to accomodate the locking lug + spring see pic 4…
A simple holder to mount V-mount batteries to the wall for storage. On the bottom there is space for cables. Step file is included if someone wants to modify it.
Print in place. Simple, easy, holds a lot of batteries
Print Settings Printer brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2 Infill: 20 ... 100
Mild remix of Virchow's battery clip design. I really liked the original, but I only needed 2 bays, and I've enlarged the dimensions slightly so the OEM Ricoh DB-110 battery slides in easily. Print Instructions ≤ 0.2mm layer height No…
Simple battery organizer that fits into 2x3 gridfinity base and can hold: 44 x AAA battery 23 x AA battery 3 x 9V battery The height of the box is 9 units. Created with Gridfinity Generator Easy to print. No supports needed. I used PLA,…
I have a lot of Zigbee sensors that use coin cell batteries, and honestly, I’m tired of constantly replacing them, especially since they’re quite expensive. On top of that, when placing the sensors outdoors, the batteries last less than…
Compact & simple to assemble laser pointer (60mm x 30mm x 20mm)
Battery mount for the Flex 24v batteries printed standing up with tree supports for the small overhang
A simple Battery holder for multiple AA batteries. I created this in MS 3D Builder as I wanted to experiment with my leftover batteries and small electronic parts. You need to buy a set of battery contacts / battery springs like this from…
skeleton Festool battery wall mount leyer hight 0.20mm infill 15%
So, this is just the battery hatch for an old JVC TV remote… I believe it's the JVC RMC384. I got one and the hatch was taped on, so I thought I'd model a replacement. It fits perfectly, best to print in PETG for strength on the tab. I…
A simple wall mount for using this USB battery charger when not in use
This is a hanger to mount to a wall to hang Milwaukee batteries. It is printed in PETG.
Summary Upgrade x20 team Parkside 2.0Ah to 6.0Ah use 10 sony 18650 vtc6 need 4x 30mm m3 bolts for replacing the original locking screws Print Settings Printer brand: Creality Printer: CR-10 Rafts: No Supports: No Resolution: 0.20 Infill:…
no suport needed, print as is ABS is better, i used Petg
no support needed battery connecting boxes check on: https://www.printables.com/model/1119580-26650-battery-connecting-box
Nothing special to add here, I gave it support enforcers with below settings underneath the protruding pins: If you would like to support me - you can buy me a coffee :) Please try to share photo of your print <3 Check out my other models…
The ultimate skadis mount for your Einhell battery. My models use a rather tight fit on the skadis universal hook, since I prefer when the hook sticks to the holder instead of the pegboard. As such you can usually take the holder off the…
i wish to abuse 18650s from 2011 and thus i needed to create this, i haven't tested it yet so not a clue if it works but i mean it should. I'll test it once i get my printer back.
ECO-WORTHY 12V 8Ah 96Wh LiFePO4 Battery with F2 terminals on 45mm center “SLA” form factor : 65.5mm(d) x 151mm(w) x 93mm(h) [ Need to scale for different batteries ; now includes: original ECO-WORTHY model with terminals set at 45mm…
The case accommodates two 18650 cells connected in parallel and incorporates a TP4056 module for charging. A JST-XH connector serves as the output interface. Assembly Instructions: Place the 18650 cells into the holder and connect them in…
Box for used batteries 9V battery style Dimensions : 91x60mm, height 160mm Need 4 magnets diam.4 x 2mm Case: Layer height 0.2mm Infill 15% Model color Black then Copper Color change at 105mm Pause at 151.6mm to place the 2 magnets (4x2mm)…
Easily store your EGO batteries out of the way and off the charger while not in use. For any modifications, here's a link to make a copy of my 3D geometry in Onshape If this helped you out, tips are welcome on PayPal or Venmo If you…
Witam! Prezentuję uchwyt na baterię 18V marki Festool z kanałem powietrznym AIRSTREAM. Pozdrawiam!
Update (2025/02/01) : Minor edits to lid, specifically made the screen hole smaller and extruded a hollow box to prevent items from ingressing via the screen hole. Parts needed : 1xLid. 1xBase. 2xButtons. 4xM3x10 screws. Depending on your…
WARNING! Lithium batteries are dangerous and can easily explode if mishandled. If you don't know what you're doing, don't do it. Not only will this kill you, it'll hurt the whole time you're dying. These parts were made to be a lighter…
Had a spot to store some rechargeable batteries, this fits the space. Stores 17 AA's and 9 AAA's in a wall mounted holder. Overall size of 251mm x 44mm x 24mm. Also included copy of "holes" used in the print to add more if desired.
This adaptor converts older Einhell battery tools for use with current Parkside 20V battery. There is no difference in battery shape, as older Einhell tools use the same battery as current Parkside 20V battery. Only difference is position…
Gridfinity bin for your Osmo action 4 battery case and spare lens cover.
Combined two models so they can be printed as one, printer can bridge the gaps without a problem
Battery Box AA Battery Crate Battery Storage AA Dimensions was changed to fit AA Batteries. And new inside for AA.
Taller version which can store up to 20 AA batteries and more than 20 AAA batteries. If your bed is a bit too small for the hight of the butler, turn it 45°. I did a little modification on the lever which will reduce or avoid the AA…
Originally made for a friend of mine, this pop-on cap is designed to fit onto a NERF N-Strike CS-18 blaster battery housing. My friend upgraded his Nerf gun to use a NiMH battery instead of the stock battery set up, however the stock…
I did 5% infill with no issues with elegoo's pla+.
This holder is designed to hold the Bosch 4A Standard battery charger for eBikes. It features a cutout at the bottom to route the power cable as well as little standoff feet so it can be mounted on top of surface-mounted cables.
No supports required. No assembly. Just Print slide in the charger and the use. Hope you like my remix.
Gridfinity coin battery holder made for a set of batteries from Lidle, the square space is to hold something like a toothpick or a sim card tool to help you get battery out.
This holder is intended for use in 600 series Roombas to convert them from using Ni-MH to Li-ion. This holder is intended to hold 10 18650s in a 5s 2p configuration. Fully charged this pack is at the upper limit of the Roombas voltage…
battery cover for gilera stalker/ to be completed, not tested.
Two handy belt clips for Olympus camera batteries types BLS-1, BLS-5, BLS-50. I use three different PEN camera's which are just great for street photografy but the batteries do not last very long. So I designed these belt clips to…
Slice using arachnee wall generator, use brim and go slow. Use 0.12mm layers Secure using M1.4 screws
This is a simple and functional AA battery holder designed to attach securely to an IKEA SKÅDIS pegboard . It allows easy access to your batteries while keeping them neatly organized. The model is optimized for 3D printing , requiring…
A friend asked me to model a battery plate for his AIWA discman. In case anyone is looking for the same replacement part. Model XP-V310. I recommend printing in a vertical orientation. it will require supports Did you like this project?…
13S6P - 18650 48V Battery Tray with 20.3mm space. This is a 48V battery for any Ebike. Cell holder with cell stopper.
Wallmount battery holder for the 12V PARKSIDE Performance ( Bauforum24 Edition) cordless screwdriver AND the battery. Is it also available for screwdriver ONLY . Made especially for users who won't let their cordless screwdriver rest with…
Hold 2 M12 batteries at an angle for easier removal on the multiboard system
Parts list: Battery contacts: 100 stücke Batteries chrapnell aa oder aaa Batterie feder 5 Nr. Positive und negative Metall batterien Feder kontakt platte ersetzen - AliExpress 13 Power outlet connector: ( Male and female) 1 Stück 5,5 x…
Cordless tool battery adapter. AEG Battery to Xfinity\Ferrex skin tools Extra hardware wire female fuse terminal x2 two types M3 x10mm bolt & Hex nut x3 Assembly should be self explanatory, reach out if you need further clarification If…
This minimalist wall mount holds a Dewalt cordless battery powered pruner. The screws go through the mount point so the tool is secure, can print with petg / pla doesnt matter as long as your screw is into something sturdy.
Link to Battery Tester: https://www.amazon.com/VTECHOLOGY-Universal-BT-168-Electrical-Equipment/dp/B07KJLBN2H Used the BOSL2 Library as well as Gridfinity-Refined-OpenSCAD for the design
a loop to replace tape or fastener to keep the batteries stay in the GoPro Dual Battery Charger . I need to charge the battery during riding. it helps keep the batteries falling out of the charger.
