Counting matching models…
This easy-to-print broom holder uses a rolling gear and the broom's own weight to securely clamp it in place. Just lift the handle slightly as you push it in place to lift the gear, and then let it settle back down to lock in place. To…
Print approx. €0.36–€0.44 excl. taxPreliminary estimate for one variant
Uses a snap-fit system to hold the handle firmly without the need for assembly. Versions -> Updated version with more grip: The model is available in multiple sizes to fit different handle diameters: Ø25 mm Ø30 mm Ø35 mm Function The snap…
use low infill if possible on this, the broom end can get heavy for the default stand. print with supports.
I have not tested with the rubber sweeper. I printed with 2 walls and 15% infill. I used 3 X 1.5" deck screws to attach to my mounting board. If flush mounting to the wall a spacer may be required to increase the standoff otherwise the…
A simple replacement for a broken broom handle cap for sticks with a diameter of 21.5 mm. It is printed with Fiberlogy Fiberflex 40D, which is a bit tricky. No support was used, but an outerbrim of 3 mm to make sure that the object is…
Broom Handle Holder V2 The new broom handle holder comes with significant improvements over the previous version. The design has been optimized to be more compact , while maintaining excellent strength and practicality. On the sides,…
My broom didn't came with a clip so I made one. The clip fits on handle with diameter 21-22mm. I printed in PLA, but I suspect it'll deform over time. Easy fix with a hairdryer. Use tight fit model for better grip. I used 0.26mm layer…
This is an upgrade….. this broom has a bigger pin. the other type was far too flimsy…! here is a pretty witch on a broom. I wanted her big enough to see some detail but then the broom was too big to fit on the build plate. the pix show my…
I liked the Broom Holder - Portascope from @Emanuele and I wanted to mount 4 brooms on the wall. But since we use bricks and mortar in my country for buildings instead of drywall, I felt it a bit too much to drill 8 holes in my wall. So I…
A simple clamping mount/hook to store a broom or mop hanging from a door. Can be printed without supports in PLA or PETG. My version is printed using 0.2 layer height and 0.4mm nozzle
A connector for 3 broomsticks in a perpendicular placement. Print 2 identical units and connect with a 35mm long M5 bolt with wide washers on both sides. The connector can be mirrored if you desire a left handed axis placement.
I have an older Subzero brand extendable snow broom that finally broke during a spell of bad weather. So I made a new part for it. Maybe it's useful for someone else as well. May fit other brands or have other use cases. I printed it in…
Allows mounting of 2 meter moxon antenna by DL2MAN direct to a painters pole or broom handle.
This is a modified version of the excellent print-in-place broom holder by fns720. In this remix I removed the side screw holes and added them on the top , allowing the holder to be hung as close as possible to a corner . Toto je upravená…
Mini Broom 🧹 This compact 3D printable broom is designed as a fun, functional, and highly detailed model. The sweeping surface is formed by ~7,500 fine bristles , giving it a realistic look and texture. Dimensions Broom head: 120 × 40 mm…
I managed to break the plastic bracket on more than one broom so I modelled a new one. The size refers to the minimum diameter between the 'teeth'. Please see screenshots for a better explanation. Holes are modelled at 4.5mm for…
Designed for hanging and retrieving potted plants originally, but could be useful for hanging Christmas lights or bird feeders. Print on the flat side with the long hook for strength, this is is intended as a friction fit, not a screw…
Socket/mount for broom handles with a size of 85 × 56 mm and a handle diameter of 28 mm. You can use FreeCAD to customize measurements. If you ask nicely, I might add your size for download. Keep in mind that the handle will change its…
This is a pre-supported miniature from Armoured Up Minis designed for use with Pathfinder, Starfinder, D&D and similar games. It is scaled for 32 mm, and ideal for resin printers. All models we produce are totally free. Each month we…
A simple broom holder hook which fits on a metal rod screwed to a wall. Allows easy movement along the rod. The STL assumes a 6mm rod positioned 16mm for the wall. The F3D source is fully parametric so allows modifying positions. The…
Uses a snap-fit system to hold the handle firmly without the need for assembly. Versions -> Updated version with more grip: The model is available in multiple sizes to fit different handle diameters: Ø25 mm Ø30 mm Ø35 mm Function The snap…
Latchable broom holder (print in place). STL is for a shaft of approx 24 mm. This design is very easy to modify with the included CAD filles. Modify the files, and update the assembly. Then save the assembly as a single STL (or STEP…
Model for broom handles from 18 to 26 mm with new system to avoid gear leakage. If you like it, a like would be appreciated Thanks.
A print in place latch to hold your Ø22mm broom handle. I made the diameter of the latch smaller to accommodate Ø22mm broomstick/handle and countersunk hole
This was actually created to hold a dishmatic brush, but can work for broom as it is fully parametric. Current screw default is for M3 screws. ---- Source code provided, so you can learn and make other similar remixes. Some ideas to…
Give your broom a new cosy home, anywhere where you can drill this hook to ;)
This is for Peggy Perfect threaded broom Easy to print, I use NoBuFil PCTG Alu Gray with 0.4 nozzles, 0.2 layers and variable heights 6 perimeters and only 25% filling gyroid Happy printing and a happy wife Dies ist für Peggy Perfect…
Broom holder replacement for the Carrefour washing flat broom https://www.carrefour.fr/p/balai-a-plat-lavant-carrefour-3270192677305. Recommendation It's recommended to print the holder in horizonal direction so that it makes the holder…
This item permits to hang until 4 brooms. It's better to print it in PETG so it's more flexible. Screw's diameter : 4mm. Distance between the two holes for the screws is 15.1cm from the center of the hole. 15% infill is enough.
Printed in petg Print settings: 100% infill (100% parameters) Supports: no This part does not need hardware to install, and does not need support to print. It's compatible with Nilfisk Neo Vacuum cleaner (The design is derivide from the…
I printed in PLA with 4 perimeters and 20% infill and no supports. I recommend printing in something better suited for outdoor use like ABS or at least PETG.
Connecteur entre la tête et le manche de balai. Diamètre manche 1.9 Impression vertical ( filetage en bas ) - sans support - Activé rendre le porte à faux imprimable Fonctionnel - Solide - Testé et approuvé
layer 0.2, first layer 0.2 at a height of 1 mm (layer 5) pause or change the material to another color. I used a combination of yellow in the background and black for the information graphics/text It is of course possible to change the…
Fully Parametric Broom/Pipe Holder Edit: Added a step file Edit: Added a new file that fixed the extrude for over 30mm diameter Print Settings Printer Brand: Creality Printer: Ender-3 V3 KE **Rafts:** No Supports: No **Infill:** 10-30%…
I made broom for dummy/ lucky 13 , there are two different brooms. Choose which one you like and get them cleaning.
Modified GavWorks work by adding extra support around where it broke for me. Also made it smaller to use less filament. Strongest if printed on its side. Save yourself the hassle and just do 100% infill. Category: Parts
outlined broom icon for use in 3D modeling, it doesn't make sense to print
1:12 Scale Broom Kid Door Print instructions Category: Buildings & Structures
Astoroth Star amulet (Bedknobs and Broomsticks prop) just as seen in the movie.
Simple 2D wall art - A Witch on a Broomstick If necessary, you can set your own size. With a layer height of 0.2, you only need to respect the height of the Z axis (0.6 mm - 3 layers - only 0.4 mm - 2 layers is also possible). Feel free…
This remix allows you to mount @LoboCNC's great Gravity Broom Holder on a Gladiator wall system . Build instructions: Filament: PLA or PETG Infill: 15% Supports: Yes, use tree / organic supports on the broom holder only. The gear can be…
Designed this to move and/or flick leaves out of my gutters. In particular it is good for moving leaves away from the gutter down spout to stop water overflowing the gutters. You are working blind with this tool so it is definitely not a…
Cutout style witch on a broom stick flying over the moon. Witch and Moon are seperate on this one but I was able to print them together on my printer with no issues. I'll be uploading an additional separate option soon tho. Thanks
The stick of my workshop broom has come loose. Then I realized that I don't have a matching Prusa design broom yet. Due to the filament consumption not cheap but a must for a Prusa printer Der Stiel meines Werkstattbesen hat sich gelöst.…
I had the original grip design break when using it as a pump grip on a nerf blaster, so I made this version where the neck is solid and it uses a bolt to secure it to the rail, and the inside becomes a storage container. Hardware: M5 x…
broom and handle made fully in plastic
At first, I didn't want to publish this model. It's too simple and everyone can make it themselves. In addition, it is suitable only for those who have such a set of a broom with a scoop for the lazy. And then I realized that the Chinese…
TPE-83a eSun Layer High 0.2 Layer Widht 0.4 Temp 240 Speed 20mms Ready in 7 Min
This model is able to connect the Dyson accessories (heads of aspiration) to the Handy Force Ariete 2761. Print is easy and not so strict with tolerances.
use low infill if possible on this, the broom end can get heavy for the default stand. print with supports.
Mesiac som vytlačil z PLA žiariaceho v tme a čarodejnici z čiernej PLA. V tme pekne svieti.
This is broom table can used for various occasions and parties especially for hallowein party. The chocolates decorated here are for illustrative purpose only you can decorate and cater your creativity on this accordingly. This is a…
Magical Broom and Bucket It would really help me out if you could “like” this model and download it. Thank you in advance for you support. Also, if you could post photos of your prints! Semper Fidelis.
Pole holders mountable on wall or any other straight surface. I use it in my chicken coop for roosts or perch that are easily removable for cleaning purposes.
Diseño para acoplar un churro de piscina de 90-100mm de diámetro a un mango de escoba para quitar agua después de la Dana en Valencia. Hay distintas opciones de impresión, para mango de 22mm (mango típico de escoba) o 32 mm con un…
I have not tested with the rubber sweeper. I printed with 2 walls and 15% infill. I used 3 X 1.5" deck screws to attach to my mounting board. If flush mounting to the wall a spacer may be required to increase the standoff otherwise the…
This 3D model is a custom-designed standing dustpan head, created to fit a standard 22mm diameter broom handle (handle not included). Designed for use in a standing position, this dustpan model features a vertical handle socket to provide…
A simple replacement for a broken broom handle cap for sticks with a diameter of 21.5 mm. It is printed with Fiberlogy Fiberflex 40D, which is a bit tricky. No support was used, but an outerbrim of 3 mm to make sure that the object is…
Very simple wall mount bracket to suit a 21mm broom handle. Spaces the broom far enough off the wall so the head just touches the wall. Printed in TPU 95a with 35% infill. Should be easy to scale the model up and down to suit different…
This thing is a remix from AndreaSignoretto's original handle. As an improvement ot his version, I added a rotating handle in order to better reach corners as well as a hole to fit a broom at the end to reach high corners. For those who…
Simply sleeve for Screw that includes hooking feature to retain broom / mop on wall. Need a 2"+ screw and proper wall structure / anchor to mount. https://www.swoptcleaning.com/collections/brooms-brushes
A wall mount designed to hold a broom, mop, or I guess anything that has the ‘standard’ sized broom shaft. It holds it off the wall to keep the broom or mop part from touching the wall to help keep it from being beat up. The bottom of the…
You know those broom clips that mount on the wall? I've never liked them. Not just the fact that they often break, never seem to be the right size, and that you've got to drive screws through perfectly good drywall to mount them, but what…
modified the original file to allow 2 objects to be held only using 3 screws
A simple clip broom holder. Designed from 21mm pole, but parametric fusion file allows easy modification. Print on side for maximum strength.
Wall hooks for mops in several versions. Standard model with 5 hooks. The distance between the screw holes is 245 mm. The base size is 250 x 40 mm. The second version has the same dimensions, but 3 hooks. The third version - 3 hooks, the…
This thing is a great example of something useful you can do with your printer. It allows you to hang any broom or rake like object using a convenient click in, click out latch. This youtube video shows and example of one in action…
A portable broom stand holder designed for organizing cleaning tools, compatible with various vendor products tested under CENRR 36000OPA standards. It includes adjustable slots and hooks for brooms, mops, and smaller tools, along with a…
Handles for two common sizes of Broom and Bush sets in Norway and a clip to hold them together. I printed them in PETG with support and brim because of rounded edges. A bit of filing was needed to remove support and brim and get smooth…
THIS IS NOT A FIREARM OR FIREARM COMPONENT, NOR CAN IT BE CONVERTED TO BE SUCH. THIS IS A TOOL TO ASSIST WITH PAINTING OR APPLYING HYDROGRAPHICS I needed a better way to control an AR platform pistol or rifle while painting it and…
Upcycle a broom stick into a telescopic microphone stand Standard telescopic broom handle with 24mm thread Base with 27.2mm hole for 27mm interference fit with broom handle (Remove the hook if present) Render Printing Microphone Clip and…
My fanwork to the dungeon and dragons Broom of Animated Attack. You can support me on https://www.patreon.com/Schlossbauer if you like my work. Category: Toys & Games
Adapter mount to mount the stick on the broom. My broom broke after long time of use, but a few minutes drawing in Onshape I made my own replacement adapter (24mm). Printed with PETG Check also my other designs:…
This model allows you to mount your 2E0ERO magloop antenna to a broomstick. Given that you can get a painter's pole that extends to over 20 feet, it makes a great, ready-made, telescoping, cheap mast for your antenna.
This is a replacement part for a broom handle / Brush Handle. To connect the handle to the brush. Plate is 50mm x 75mm, angle is 25 degrees I have included 4 screw holes(4mm), a drainage hole in the center of the holder (3mm), and a hole…
This 3D-printed wall-mounted organizer is perfect for holding a variety of brooms, tools, and equipment. Designed with a sleek, lattice-style backing for a modern look, it features sturdy hooks and slots to securely store items like…
Created to cover jagged metal on end of broom handle. Sized for 23mm handle. Fits snug. Handle hole ends well before top of cap to ensure metal won't eventually wear through. printed as oriented though a 45deg tilt would probably be…
The Vildea Sweeping set didn't have a clip, so the Broomstick did always fall down. Clip designed and Printed, problem solved…. Das Vildea Junior Kehrset enthielt keinen Clip für den Besen. Deshalb lag der Besen ständig am Boden herum.…
broom (mop) holder for pipe. Ideal diameter of the pipe is 22mm. You will need 2xM3 nuts and 2xM3 (20mm long) screws.
A replacement handle grip that can be scaled. Currently fits broom stick handles ~ 21mm Print settings .2 layer 3 walls 30% rectilinear infill Slower print speed Thanks for looking, Enjoy.
Simple pressure clip room holder with screw holes. I made the back plate large enough for a command strip as well. Holds standard diameter broom handles. Printed with 15% infill, 3 perimeters on a 0.8 nozzle in PETG. Should work fine with…
It has a hole for a M4 insert so that it can be mounted on a fixed shelf bracket. It was made so that I can hang my filaments on the wall. Printed in Turbo-PETG
I had trouble with the original due to it's short reach, so now i can just add however long stick i want…
Small handle for the Aquablade squeegee we use in our shower, with a loop for hanging. The threads look like a standard broom-handle thread so it may work with many other tools. PETG, 0.2mm adaptive layer height, 0.4mm nozzle, printed…
Remix of @LoboCNC's excellent Broom (or other tools) holder. I added Multiconnect slots to the back so it connects to Multiboard . @LoboCNC: “This easy-to-print broom holder uses a rolling gear and the broom's own weight to securely clamp…
This pic grip requires M3 hex head screws and accompanying nuts. If you are using the broom stick as a primer I recommend printing the handle horizontal to the table and using 5 Walls 5 Top and 5 Bottom with 20% triangles infill. ( I use…
