Counting matching models…
My garage door keypad, an 877LM, can close the garage door just by pressing the enter button, no code needed. When I walk the dog, or take a car not parked in the garage, I want to easily close the door on the way out, and was annoyed…
Bei den Chamberlain Fernbedienungen für Garagentore bricht sehr leicht der Hacken für den Schlüsselanhänger. Daher habe ich mir die Rückseite und den vorderen Clip gezeichnet und Gedruckt um diese Teile ersetzen zu können. Sparrt einem…
SkekSil, a character of Dark Crystal series.
Recommend printing with support
I have a Craftsman garage door opener from about 2006. To change the battery you have to open the remote case, which is held by tiny flimsy plastic pins… which broke over time. That means both half won't stay together and the battery…
Decided to mount my garage door openers on the wall next to my door openers in my garage to easily find/give to someone when needed
this is toolless sun shade for Chamberlain garage door safety sensors Print Settings Printer: Voxelab Aquila Rafts: No Supports: Yes Resolution: .2mm Infill: 20%-50% Filament: Sunlu PETG Category: DIY
Made this replacement gear for my Sears 41A4315 but should fit a lot of older garage door models from the 90s or 2000s.
A clip for your visor that fits the Chamberlain (liftmaster) garage door remote. 2 sizes here for thick and thin visors Print in PET-G as PLA will likely soften in the heat inside car. Support is required. Sliced versions for both the…
This wall plate allows you to neatly place two Chamberlain (Or LiftMaster, or Sears since they are all made by the Chamberlain group) wall control panels side by side. It has channels on the back side to hide the wires. You can use a…
The purpose of this is for it to be placed near the door or wherever you might commonly have to open the door that not near the actual opener without running a wire. I used small drywall anchors to hang it on the wall. One hole is taller…
I just changed from a 20 year old Genie to a new Chamberlain B750 with a quiet belt drive so here comes a new shield design. I looked around and didn't see any commercial units that I couldn't think of a way to get around so I made my…
This is a clip that slides over the remote and then can be clipped onto the sun visor. Printed in Hatchbox PETG
Chamberlain wanted me to use double-stick foam to mount this to my garage door... I don't think so. Disappointed that no-one created one yet, so here you go. I added a ridge around the top and bottom to secure with a tie wrap, should it…
This is the door sensor for a Chamberlain myQ smart garage door kit. Great way to add smart controls to a garage door for just $20. Could be tighter on design for sure. But for 15 minutes in fusion it works as I intended. Four 6mm x 3mm…
This is for the newer chamberlain myq hub (MYQ-G0401-ES) I wanted to be able to velcro mount or use command strips to mount my Chamberlain myQ hub on the wall rather than drill, so i created this backplate that fits with the stock mount.…
This is the coupler that connects the motor and the screw rod for a garage door. it should fit all Liftmaster Screw Drive and Low Profile Screw Drive operators (1995-current), models 1000SD, 2000SD, 1000SDR, 2000SDR, 2110, 2220, and…
This remix shortens the original Garage Door Sensor Sun Shield by 20mm to better suit the Chamberlain Group LiftMaster 041-0136 safety sensors. The adjustment ensures a cleaner fit without interfering with alignment or mounting, while…
NOTE (Nov. 1, 2023) : See improved versions here : https://www.printables.com/model/633299-safety-cover-for-chamberlain-remote-control-garage This “safety cover” is for the model 953EV-P2 Chamberlain 3-button remote control for garage…
Gehäuse für die Funkfernbedienung am Chamberlain Garagentor. Ist für die alte Version mit 433 Mhz, ob es für neueren Versionen passt kann ich nicht sagen. Wenn ja, dann bitte Rückinfo ;-) Die Knöpfe sollten vor der Montage noch ein wenig…
"Please... please... hmmmm?" Bring the most complex antagonist of Thra to life with this high-fidelity representation of skekSil the Chamberlain. This sculpt captures the internal duality of the character: the outward projection of a…
Some time ago I made a “safety cover” is for the model 953EV-P2 Chamberlain 3-button remote control for garage door openers(see photos). That cover clipped onto the remote to prevent accidentally pushing either of the two smaller buttons;…
The original keyfob keyring slot is thin and weak and broke very quickly. This case snaps over the original case to provide a beefy keyring slot. This is a very tight fit on purpose. The original keyfob will snap into it with some brute…
These are replacement temples designed to fit Warby Parker Chamberlain frames. I wanted to make colored temples for my glasses, so I designed this part. Make your own funky parts, or fix your broken glasses. Enjoy. Note: I've provided the…
The chamberlain WiFi garage door opener phone app has not so great reviews (it show advertisements). The SwitchBot button clicker works as an alternative that is more reliable. Also one less app on the phone and wifi device Printing with…
There's about 0.8mm of clearance between the bracket and the remote. You could take this down a bit to get a more secure/friction fit. The hole on the bottom is not entirely necessary and only intended to make it easier to remove. If I…
Chamberlain replacement gear knob to suit Super 90, will likely suit Super 70 and other tractors. 1/2BSW thread internally (recommended to run a hand tap through the thread to clean it up once printed) Designed to be printed and epoxied…
An meiner Garagentorfernbedienung ist nach Jahren des Gebrauchs der Schlüsselring am Gehäuse abgebrochen. Alternativ zu meinem Gehäuse https://www.thingiverse.com/thing:3330457 habe ich nun noch eine Hülle zum Einschnappen der…
Overview: This is a sun shade I designed for Chamberlain/Craftsman/Liftmaster compatible safety sensors. It is tested with the Chamberlain Model 820CB, but should work with any similar Chamberlain/Craftsman/Liftmaster sensor. Why Do I…
Made this for my brother in law who had lost his original battery cover for his Chamberlain garage door opener.
Ford Maverick has an odd little cubby to the right of the screen. Nobody knows what to do with it, but that hasn't stopped any of us from all manner of wild speculation and model creation. To that end I give you this model which allows…
A Chamberlain / LiftMaster Mini Universal Garage Door Remote Holder, to mount it onto the center console. It is designed to be compatible with 3M Command Outdoor strip for secure mount and easy removal. It is designed to fit Kia Niro EV…
print fine with ASA I did 0.02mm layer height with a couple supports for stability
Light switch cover for 1 gang box for Chamberlain 1 button wall mounted garage door.
Ich habe diese Tastatur dieser Tage austauschen müssen, weil die Tastatur wohl unter der Witterung (Regen hauptsächlich wohl) gelitten hat. Es dauerte bis zu 15 min. und entsprechende Eingabeversuche, bis es endlich klappte. Das sollte…
If the Sun is stopping your IR Beams from working this might help Tinkercad model https://www.tinkercad.com/things/aaDceWmcOyn
Out of necessity I have designed and 3D printed Chamberlain Dash light rubbers for my Super 90. Print in TPU
Fits remote dimensions: 88mm, 40.5mm, 19mm Useful for either velcro or double sided tape to stick somewhere in your vehicle. Current setting is more flexible in the back for sticking to non flat surfaces.
This print is for the Chamberlain model 953ESTD. This remote control unit comes with a metal clip to use for mounting to a car sun visor, but this is not always a convenient location. These two versions of holders for the remote control…
Chamberlain IR Beam Reflector Shield. Printed in ABS. Please share your Makes 😎
Comme 2 de mes couvercles de boutons avaient cassé, j'ai décidé de les recréer sur Fusion, et je partage au cas où vu la spécificité du besoin. Modèle : Minuteur / Horloge programmable pour motorisation de volet roulant, CHAMBERLAIN…
Backplate for Chamberlain (LiftMaster) Commercial Gate Operator front access cover. Printed with PETG. Please share your Make:) Like the freebie? Feel free to buy me a cup of coffee with the link above ;)
Divide the part into objects and assign the knobs and led light into the colours of your choosing, but not necessary. I have used PLA-CF black and a see-through white like Litho-PLA Cover simply presses into the four un-used screw holes.…
This is the coupler that connects the motor and the screw rod for a garage door. it should fit all Liftmaster Screw Drive and Low Profile Screw Drive operators (1995-current), models 1000SD, 2000SD, 1000SDR, 2000SDR, 2110, 2220, and…
