Counting matching models…
I wanted a dead simple top mount for my Sturdy Bunny v2 ERCF without using any 2020 extrusion. Taking inspiration from jeoje's Sturdy Handles I made two platforms that mount to the frame using a single M5 roll-in nut and M5x10 bolt.…
I got sick of trying to use an adapter so that my Waterbox aquarium return pump would work with ½ inch locline fittings. The original ½ inch adapter that I got from VCA broke, so instead of making a new adapter, I decided to design a…
This is something I made for my Biocube 32 Gallon aquarium. I got tired of looking for something that would fit and where the connections were actually strong and not fall from just touching them. This is what worked for me and it fits my…
Designed a stand for my new Minilab 3. Has been holding up well and fits like a glove. Put rubber feet on the bottom to prevent sliding. Very sturdy print Prints without any supports or brimming. .20mm layer height PLA If there is any…
For my use case, I needed a stand with a steep angle to see the floor in one of my rooms. It fits really snug, so depending on your printer and settings you might have to experiment with the step file a bit.
Inclined Base for the Eureka Mignon Series The Stand is tilted forward by 9deg to decrease retention just like the new Eureka Mignon Single Dose Grinder. It precisely fits on a Prusa i3 MK3S (with skirts turned off) The front is designed…
Make sure your walls are thick and consider printing slightly hotter than usual for better layer bonding. The top rim can be a little temperamental, but holds firm once the grinder is in place
Large Waterbox aquariums (like Reef 220.6) have DN220.6 return nozzles. Metric locline components are hard to find. This part replaces the screw in locline adapter with an adapter with M20x2 threads to ¾" locline.
Simple riser for 14 inch M1 Macbook Pros. Only difference between the models is width and I think 15mm is plenty strong.
This is a simple angled mount, it's made of 2 pieces just for versatility since the first plate is a flat one made to just rise the whole assembly higher. The second plate is the one that angles the mount, you just need long M5 bolts that…
Inclined Pedestal for Busts Elevate your miniatures to their full glory with this inclined pedestal. Print or decorate it to suit your preferences. Pedestal Dimensions: Width: 3 x 3 cm (excluding decoration) Height: 7 cm Rod Diameter: 3mm
Like it says in the intro. . . The powertrain and basic sheetmetal of Dodge/Ram vehicles tend to outlast the plastic components. Having a ready source of replacements is key to really racking up the miles. . . . The “Repair” contest…
This stand has a 25 degree incline. Print it with supports. On the bottom there are 2 recessed places for a rubber sticker. If you don't want to add this, just don't remove the supports.
For this lifter, the shape was created that uses as little plastic as possible without losing strength. There are also two areas where non-slip material can be inserted if needed. If you print this, please leave a like or share a make!
When introducing Newton's laws in physics, defining forces acting on an object on an inclined plane and drawing free-body diagrams are important skills. Students often struggle with the correct angles. This hands-on model demonstrates how…
This cylindrical timer rolls down the inclined plane very slowly, at a rate of 20cm per minute. It is inspired by traditional Inclined Plane Clocks and is very similar to the popular clock mechanism Tourbillon , except that in this case,…
My recliner sofa handle broke so I modelled up and printed this, you will need to run a 5mm drill down the hole once printed but otherwise works well on my chair. I've included the fusion file so dimensions can be changed to suit your…
This is a remix of the 25 degree stand. This stand has a 35 degree incline. Print it with supports. On the bottom there are 2 recessed places for a rubber sticker. If you don't want to add this, just don't remove the supports.
A replacement for the stock seat recline knob in the Hyundai ix35. The original one in my car was getting janky, so I modeled a new one. It's comfortable to grip, holds up well, and you can print it in whatever color suits your interior.…
Fan duct for the E3D V6 hotend Print instructions Category: 3D Printer Extruders Summary Fan duct for the E3D V6 hotend
UPDATE: currently finished the project these tracks were used for vid here on my yt channel check printables comments for updates Another UPDATE: modular bridges are now supported, take a look in the onshape link to download them, they…
This reduces ¾ inch locline down to ½ inch locline
My Ekornes Stressless recliners were not holding in place well any longer. The issue was that the “pads” were worn out. Printer to the rescue. I designed these pads to bring new life to my recliners and I am so glad they worked! I printed…
Originally sold by BaristaByDesign on Etsy (that's me), I've decided to pack in making and wanted to release the model for everyone to use. Make sure the walls on your print are nice and thick and bond well to one another. Consider…
Print it out on its smallest face or however you want. There are recessed grooves on the back for 10mm 3M VHB tape to stick it to the Lovesac Angled Cup Holder.
I wanted an adjustable dust collection solution for my drill press. This solution uses a 2-1/2" Loc-Line [1] mounted to the drill press with a 14" 2x4 [2]. It joins with a regular 2" shopvac hose via this thing (3D printed coupling). The…
This mousepad is 204mm wide and 217mm long. The cup part is 84mm wide and 67mm deep. Resize in your slicer as needed. Print settings: 3 walls, 3 top and bottom. 15% grid infill. Made with PLA, but PETG should work fine.
Simple Inclined Desk Organizer
Replacement block for OKIN JLDQ-12B linear actuator. Part number: JLDQ.12.109.80 After having this part break on both our chair AND half the couch... replacement actuator assemblies are $90 on Amazon, and the block is not available as a…
Parametric Tapo C210 inclined wall mount. You can change the inclination angle in the spreadsheet. I printed it in PLA with 4 wall loops and supports for critical regions only.
Expobar Brewtus Tamper station E61 for inclined portafilter UPDATE: Added a bottom and tamper holder in version 2 This is a tamper station for the original portafilter that is coming as standard for the Expobar Brewtus series of espresso…
Passenger Seat
The name and summary cover most of everything. If you have an Amia you have most likely been frustrated by being limited to being locked upright or going into full recline. This model gives you 4 options for recline in 8 degree…
I live overseas so when the driver's side seat recline lever broke on my 2015 Jeep Patriot, I decided to try making a replacement that would at least be functional until I could find a factory replacement. The factory part number for this…
I got tired of the broken clip on my power recliner and the missing clip on my powered standing desk, so I made this and printed it. Isn't it fun to 3d print fixes for broken things? Due to it's small size I printed it out of Anycubic…
Model in the photo is different. The stl I provided does not have the heart extruded from the surface but is hollow on both sides.
My drawers are not too deep (70mm) and CNC milling bits do not fit the drawer if stored vertically. Also, some of my bit boxes are 14mm wide, and do not fit most of the holders. This tray holds milling bits inclined, and long bits fit my…
The idea comes from Habony Norbert. This is my version of a filament guide. Ideal if the spool is on the left or right side of the printer. It is plugged into the modified Z-top of the MK4/MK3. The angle can be infinitely adjusted by…
Replacement for Nissan Cushion Assembly Knob part 87013-7S001 . Modeled from the switch on my 2007 Nissan Titan, but should work for many other models.
This model is compatible with the lego system.
Inclined stand for the SONOFF SNZB-03 zigbee motion sensor. Printed in PLA with 0.2 mm quality. Simply fasten it with a wall screw through the hole provided, the sensor fits inside from the top and remains secure, allowing it to be…
A cold shoe receiver with 3/4" Locline connector. Includes hole for power line. Inspired by Adam Savage's light rig.
The model presents the behavior of a double cone on an inclined plane. Let's drop a tube down an inclined plane. It will roll down. It's no wonder. Now let's place a double cone at the bottom of the inclined plane. The lump will go…
I printed mine in PLA, 0.2 mm height, 20% infill, 3 walls (4 or 5 would be better). I also made improvements to make it stepless, minor improvements or adaptions to the funnel and anti-popcorn lid. Consider also printing: Stepless…
My recliner foot rest release pull handle broke. I glued it back together and scanned it. The original was designed to save materials. I just made it solid. You can purchase replacements: https://amzn.to/44Sru23 , but I just needed the…
A zip-tie mounting bracket for 1/4" locline hose
This is a first batch of my remix of Extrutim's Kurzgesagt bird fridge magnet models. The difference being that these can not be printed as separate parts and glued together, so multimaterial capabilities are a must. I have made parts…
M5 Flange for Locline Printermount for 3030 Extrusion with male connector to Locline. I have been inspired by the ideas of @cmh and his models and played around with mounting locline pipes to the prusa 3030 extrusion. For mounting the…
Replaces the block on actuator on recliner, works good on my recliner.
This model is based on a maze of mysterious origins located in Chartres, France (and maybe a few other places across Europe). I made it small enough to accommodate a small BB sized bead. This one prints without supports in your resin or…
Recliner Actuator Block Replacement - MotoMotion / MOTO / HHC Power Recliners What is this? A 3D-printable replacement for the arched actuator moving block (also called "slide block" or "traveling nut") found inside the linear actuator of…
Three-piece stand that angles your Eureka Mignon coffee grinder 15° forward. Print in any material, PLA may deform with time but has held up for years for me in this application. Use four M3 screws and nuts to attach the feet to the base.…
The whole VAG seat recliner knob, tested and working in a Seat Ibiza 6L but should work on most of the vag group cars of that era (approx.. 2002) Please don't print this before testing the mechanism alone. I've posted the mechanism for…
Remix of BigSlowTarget's model. This is a replacement part to fix a La-Z-Boy recliner if the original plastic piece that holds the footrest mechanism together breaks. If the footrest is broken but you can visibly see the motor still…
This is a replacement pull handle that fits onto a steel wire cable for a La-Z-Boy sectional recliner. The steel wire needs to have a ball end that the handle will slide onto. Included is a plug that then slots into the handle to retain…
A broken handle on our couch necessitated this build.
The cup holders in our recliner are too small for my coffee cup. So I printed this tray platform to adapt the cup holder to a flat surface. There are two options, one with a rim, and one that is a lego-compatible surface. If you're…
This is a replacement handle for adjusting the tension on a vintage Ekornes Stressless recliner. This works with the friction fitting here: https://www.prusaprinters.org/prints/82858-ekornes-stressless-friction-mating Insert a 3/8" hex…
Stressless Recliners Spare Feet to clip between the plastic and wood ring
M5 Flange for Locline Printermount for 3030 Extrusion and UNF 1/2" 20TPI Threaded Locline. I have been inspired by the ideas of @cmh and his models and played around with mounting locline pipes to the prusa 3030 extrusion. For mounting…
A few years ago an Adam Savage video showed how he made a light for his work bench using LocLine to be able to position it where light was needed. I finally decided to copy the idea. Vast amounts of babbling about my build can be found…
Replacement bracket for the front legs on some "Zero Gravity Lounge Chair" recliners. I designed this for a coworker that lost the original (somehow). Here's an example of the type it fits on:…
a recliner I made following a tutorial I watched on youtube
My father-in-law asked me if I could make him a slightly inclined support and a rain visor for his Video Intercom System
M5 Flange for Locline Printermount for 3030 Extrusion with female connector to Locline. I have been inspired by the ideas of @cmh and his models and played around with mounting locline pipes to the prusa 3030 extrusion. For mounting the…
Recording Artists - Patsy Cline
Just a small holder to allow my paints to sit 3 tall in my case, but may also be useful for being able to more easily pull them out by their cap. The case the starter kit came in just laid them flat, which isn't great for easily grabbing…
Remix of stand model by konseben. Added a hole for screw, so I can mount it to the ceiling.
My IKEA recliners actuator broke. Print instructions Print with high infill hollow end down with supports on hole rings only. I've printed with PETG and recently PC Blend.
My dad was replacing a recliner slide unit every time it broke to the tune of 90 bucks a pop when all he needed was the slide block so 3d printing to the rescue.
PrinterBox with the original Prusa LCD screen inclined https://www.printer-box.com/ only print these part, and screw the original prusa LCD.
Two of my kids have this drawing tablet (https://www.amazon.com/gp/product/B07GNK18VJ/) but it lays flat to the desk, which isn't great for drawing on or using as an extra monitor. One of my kids requested a 20-degree incline for it so I…
For cultivating mushrooms by pouring an agar medium inside and sterilizing it. These are so-called "slants". Sample photos are from ordinary PLA. The final version will be made of HTPLA or Nylon - it must survive 121 degrees of Celsius…
This is my first draft of a set of twelve piers for a very gradual incline for TGauge (1:450 scale) track. The pier heights increase by 2mm each. The smallest is 2mm and the tallest is 24mm (measured at the point where the track sits on…
I modified the original Heater Stand for PTC Heater design by @indymusician_238719 because my PTC heater measured 80x80mm and I wanted to keep it slightly tilted to direct the heat more towards the center of my Original Prusa Enclosure.…
Printed flat on it's back without supports 100% infill and 4 perimeters, 0.2mm layer height. I used PETG for my print and expect it to last a while. It fit perfectly for my chair without any modifications to the part after printing.…
A simple block model showing inclined bedding. It has a removable core for stimulating additional discussions during the class. We use them in our GEOL101 labs and Geological Field Techniques classes. This is one of eight models used by…
The white handle securely slides onto the Speediance bench. (btw orange handle was first version) I also used JB Weld to attach 2 wheels to the bench. You can effortlessly move the bench around using the wheels thanks to the handle. Given…
Well this recliner is aging, but the other day when the handle broke I didn't worry a bit, as I knew Prusa would come to the rescue. Without the handle, the recliner is just a chair as turning the mechanism without mechanical advantage is…
Stand for the Börner/Boerner V1 ClassicLine Hobel/Slicer Dimensions: (H)123mm x (B/W)124mm (hinten, vorne: 103mm) x (T/D)96mm
Handy door handle inclined for an egnonomic operability. Nozzle 0.4mm and layer height is 0.2. Use 3 perimeters.
25 degree drop in case for the 15 key stream deck; screw holes and slot for cord, flat bottom easy print
The reclining handle cover was missing from my SF Forester so I printed one Note: in the photos it shows a hole, however it was misaligned from taking inaccurate measurements but I found that it fits on good just with a friction fit
Just a simple recliner handle/lever replacement for when yours inevitably goes missing. Designed for a Ashley Furniture Rocker Recliner, but will work with most recliners with a square pegged leg riser handle. Print Settings Rafts: No…
Mini wheel blocks with incline and grip. Also has handy hole for rope so you dont forget to remove them. Work great as motorcycle tire blocks but you can scale them to your size.
Printed in Elegoo PLA+ 3 Wall Loops, Top and Bottom Shells Pattern Rectilinear. Sparse infill Density 15%. Infill/Wall Overlap 85%.
I needed something to hold my pens and pencil in front of me and because I have a 3 monitor configuration and thee's not much room left on the desk. I designed this specifically to fit under the monitors. Print it with the back laying on…
Modification du guide-filament “quick connect” de Printer Box qui permet d'incliner le tube PTFE pour réduire la friction lorsque le Spool Tank est posé sur l'imprimante et surélevé (par exemple grâce à ces pieds intercalaires (…
A simple block model showing a sinistral fault. It has a removable core for stimulating additional discussions during the class. We use them in our GEOL101 labs and Geological Field Techniques classes. This is one of eight models used by…
Need to organize your spray cans with style? This inclined spray can holder is the perfect solution for your workspace, garage, or workshop! Designed with both intelligence and modernity, it provides easy and immediate access to your…
This is an add-on which picks up on two of the three threaded holes on the feet for the XL base and allows the user to attach LocLine based helping hands for soldering/small fiddly jobs. Designed to use M8 x 20 SHCS to lock in place.…
L-track inclined at 45°, held by M6 screws from below. I use this model to secure bags in a van. Printed in PET-G with 3 walls and a giroïd filling, it seems solid enough for my needs, you be the judge ;) To be printed face down, with…
Hello, this is a replacement for the plastic grip found at the tip of the Trabant P601 Seat Recliner.This is a replacement for the plastic grip found at the tip of the Trabant P601 Seat Recliner. Its not a perfect match for the original…
Recliner Tablet Mount These tablet mounts are designed to fit into recliners that offer a cylindrical accessory slot (but that part is printed separately so if your recliner has a different form factor for accessories you can print an…
I could not find a mug holder for my recliner that I liked so I designed my own. I needed it big enough to fit various sizes of mugs as well as fit my recliners existing cup holders. Hopefully it fits others too but if not, please let me…
I prefer to hardwire my phone for Android Auto. I wanted a designate place where to place phone and storage cable slack without compromising other features. So, I modeled this part, see picture for reference, I used double sided tape to…
The plastic protective floor protectors on the feet of a recliner/rocker in our den have started to crack and come apart. We have wood flooring, definitely needed replacements to protect the flooring. These protectors are triangular…
Don't know what it's called but if you have one of those vintage chairs with the vinyl straps an the part that let's it reclines breaks, you can print another one. I printed in white PET with pretty thick walls and low infill and it…
