28 models
Looking for a solution to reliably hookup CAN devices, fans, sensors and more to your beloved 🥰 VORON with a tiny bit of 😎 premium touch ? This custom skirt for CNLINKO LP12 (and compatible) connectors might be it! Why This Mod Exists…
This is just a tiny little model for the Option Plate Mod of the 🥰 BoxTurtle's rear skirt. It accommodates a CNLINKO LP-12 💪 connector, e.g. to connect both CAN and 24V. Additionally, the design incorporates a dedicated cable outlet for…
Version 2 This variation includes slots for zipties. This is particularly usefull If you are also routing the extruder cables through the umbilical instead of using the driver on your SB2209/SB2240. Replaces the Stealthburner cable anchor…
same hardware as Nyx's linked below, CNLinko quick detach PG7 https://www.amazon.com/gp/product/B087MXNC7W/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&th=1
I just added a coutout hole in order to not have to disable the whole cable to remove it. The rigidity is good. I've been using it for more than a month now. Printed with Voron settings.
I have remixed tetsu97 's umbilical mount for G2SA with PG7 fixing point by moving it to the right. Added channels for zip-tie that is meant to secure the umbilical cable. The stl is print oriented and includes sacrificial support (in…
The original stubby mount for an M12 cable gland has an M12x1.75mm pitch. The CNLinko connectors have M12x1.25mm pitch so I re-modelled the mount to have an M12x1.25 thread. CNLinko waterproof connectors in various pin configurations can…
EBB36 Mount with CNLinko Adapter for Orbiter 2.0 and G2SA. Solidworks file posted if you wish to make some changes. Needs (5) M3 heatset inserts. I've installed this is my Micron and Trizero and havent had any clearance issues.
SB PCB/Galileo2 Strain relief mount zip tie locations that sit flush with the mount use CNLINKO M12 quick disconnect or M12 strain relief
This piece comes with Umbillical Back Cable .
Remix Details: Improved chamber seal, rear panel is now sandwiched between the cover and trim when tightened. Bowden entry threaded for a PC4-M10 fitting. Added a PG7 Key for easier tightening or removal of PG7 strain reliefs.…
remix of: https://www.printables.com/de/model/463220-voron-cw2-stealthburner-ebb-sb2240-pg7-umbilical-m thanks for the initial work! to fit plug: https://aliexpress.com/item/4001153106923.html and wire harness of one mellow Fly-SB2040…
use flathead screws
Hello! I have created an umbilical plate for the Voron 0.2. with CNlinko connectors and an outlet for the bowden tube. You still need the following things for the mod: 1x Cnlinko 4 or 6 Pin M12 (Plate Version) 1x Outlet for Bowden Tube 4x…
This is a modification to the End Cap to allow you to use the CNLINKO LP-16 M16 Connector https://www.amazon.com/dp/B0816BMDKQ?ref_=cm_sw_r_apin_dp_Z64RTF47HAMNZWPDRRAZ I had another person make this for me based on the original design
Added a cable cutout to this great design. All so added a zip tie reinforcement slot.
Exhaust cover with PTFE tube guide and 2 CNLINKO-LP12 connector outlets. Remixed the great model from @NyxCode_817344 . I have included the .stp file for further remixing or modifications.
I like it sturdy. I wanted to have the cable connection on the lateral side and a little bit lower, so I designed my own strain relief. You will need a few melting inserts and M3 screws. Enjoy.
EBB36 mount for Hextrudort-Low Plus extruder with rigid CNLinko/PG7 mount.
Thanks A1lexR for sharing. Just needed a version for threaded CNLinko LP12 terminals. So I remixed your plate. Printed with nobufil ABS+ Kind regards 3dexp
This is a remix of the original BoxTurtle part. It allows you to use a CLINKO M12 connector for the cable that runs between the BoxTurtle and the printer's main board. It's up to the builder to work out the details, but my planned…
GitHub Repository StealthMax V2 CNLINKO LP-16 Umbilical Mod This mod enhances the StealthMax V2 with a redesigned intake that integrates a robust CNLINKO LP-16 umbilical for cable management. Features Integrated Umbilical: The CNLINKO…
Per a user request, I alter the base mounting plate from my original design to work with a Hextrudort CNC Low Extruder Requires (5) M3 Heatset inserts and (3) M3x8 screws to attach the CNLinko Arm to the Extruder Mounting Plate. Spacers…
It needs 3xM3.5 countersink screws to mount.
CNLINKO LP-12 connectors offer a nice and reliable solution to connect external devices (CAN) to your printer, such as a BoxTurtle multi-filament system... For those -like myself- who connect the Voron Trident through wired Ethernet, you…
Underneath mounting LP-16 socket case. Initialy designed for a M3x20 screws.
Neu gezeichnet um Kabel bequem einlegen zu können. Es werden 2 Schmelzgewinde 3mm und 4 Schmelzgewinde 2mm benötigt.
This is a remix of the original BoxTurtle part. It allows you to use a CLINKO M12 connector for the cable that runs between the BoxTurtle and the printer's main board. It's up to the builder to work out the details, but my planned…
