Counting matching models…
CLICK HERE FOR THE ASSEMBLY GUIDE Available for $119.99 CLICK HERE TO BUY DELACK AT 3D SOURCERER.COM CLICK HERE TO BUY DELACK ON OUR AMAZON STOREFRONT AVAILABLE IN THE USA ONLY! MMU3 COMPATIBLE
CLICK HERE FOR THE ASSEMBLY GUIDE May 28, 2024 Update Added a self-threading bolt hole for the LED MIDDLE SUPPORT to allow for a bolt attaching the LED MIDDLE SUPPORT piece to the top piece of plexiglass to keep the LED attached to the…
Add extra space to your DELACK with this skirt print! Contains an option for an external LCD mount! PLEASE REMOVE ALL OF THE ZIP TIES FOR THE LCD CABLE UNDER THE PRINTER, OR THE CABLES WILL NOT BE LONG ENOUGH TO REACH THE LCD! If you are…
CLICK HERE FOR THE ASSEMBLY GUIDE
Mount your 120mm fan on the back of your enclosure with a HEPA filter CLICK HERE FOR THE ASSEMBLY GUIDE
CLICK HERE FOR THE ASSEMBLY GUIDE
CLICK HERE FOR ASSEMBLY INSTRUCTIONS
CLICK HERE FOR THE ASSEMBLY GUIDE
CLICK HERE FOR THE ASSEMBLY GUIDE 2/28/24 UPDATE Increased depth of top hex cutout per popular demand
CLICK HERE FOR THE ASSEMBLY INSTRUCTIONS
CLICK HERE FOR THE ASSEMBLY GUIDE
CLICK HERE FOR ASSEMBLY INSTRUCTIONS
CLICK HERE FOR THE ASSEMBLY GUIDE
The gaps between the door and front panel of the Delack enclosure are fairly big, and if your enclosure sits with a window near its front face you may get drafts of cool air onto your model. This seal aims to avoid those. The geometry…
CLICK HERE FOR THE ASSEMBLY GUIDE
CLICK HERE FOR THE ASSEMBLY GUIDE
CLICK HERE FOR ASSEMBLY GUIDE
We have created 2 versions of the DELACK MMU3 Mount - this is the Standard Version which is essentially identical to the positioning of the buffer and PTFE tubing recommended by Prusa during the assembly of the MMU3. PLEASE PRINT THE…
CLICK HERE FOR ASSEMBLY INSTRUCTIONS
CLICK HERE FOR THE ASSEMBLY GUIDE
CLICK HERE FOR THE ASSEMBLY GUIDE
CLICK HERE FOR ASSEMBLY INSTRUCTIONS
Add a 120mm fan, HEPA filter, and a 4" duct to the back of your DELACK or SUMO Enclosure CLICK HERE FOR THE ASSEMBLY GUIDE
Add a Blink Mini camera to your Delack enclosure. Print out and use two M3x8mm bolts to hold the camera to the corner piece. 8mm bolts were just long enough. If you use 10mm, don't over tighten then because you don't want to end of the…
The “DELACK Enclosure Modular Top Corner” kit comes with a few containers, but I wanted a larger one to hold all the Prusa Mk4 tools in one place. This is the result. I've tried to optimize it by moving the tools in order of use, e.g.,…
CLICK HERE FOR THE ASSEMBLY GUIDE ***THIS PROJECT IS IN BETA - PRINT AT YOUR OWN RISK*** To be completely transparent, we DID encounter some issues with the MMU3 when using this setup. However, it was difficult to determine if this was…
CLICK HERE FOR THE ASSEMBLY GUIDE DO NOT PRINT WITH ANY SUPPORTS - THEY ARE BUILT INTO THE MODEL AND CAN BE EASILY REMOVED AFTER PRINTING!
I have only implemented the “ribbed” rear-right-hand side. If people would like, I will do the other variants ("plain"-{left,right}, ribbed-left) as well. The only changes to the assembly instructions for the MMU3 Cassette Buffer were to…
The Delack enclosure has a skirt available for boosting the height. When used with a paver or MMU3 it works fine, but with both it was a little too close for my liking. The regular skirt also does not have mounting holes for the top…
I wanted a bottom-mounted Wyze camera so the extruder would be out of the way when trying to view my prints. I leveraged the designs from the DELACK enclosure feet files and merged them with the Wyze Cam mount. Mimicking the MK4 hex…
Mount your 120mm fan and your 4" duct mount to the back of the SUMO or DELACK enclosure CLICK HERE FOR THE ASSEMBLY GUIDE
The provided link for the DELACK enclosure has everything you need to build the enclosure. However, in my remix, I decided to route some cables along the bottom instead of the top. Unfortunately, the enclosure models did not have feet…
Print orientation As imported to Prusa Slicer – mounting surface on the build plate. Variations “Original chamfer” copies the original handle's chamfers as closely as I can “Edge chamfer only” chamfers all edges of the handle instead of…
CLICK HERE FOR ASSEMBLY INSTRUCTIONS
General I just got my DELACK enclosure and started putting together a list of parts to print and wanted to use my Wyze Cam V2 so I remixed the original mount that supported the V3 to have a slot that the V2 can slide into since the V2…
DELACK Enclosure Hygrometer Faceplate v2
I loved the simple design of the Delack but mounting the LCD was one of the most frustrating processes I have delt with in a while. This module makes the LCD screen easy to attach and detach from the DELACK Enclosure Skirt. It uses extra…
Lets you mount anything already designed for the popular articulated arm system by Sneaks, onto the DELACK enclosure by 3D Sourcerer. Very useful for mounting webcams. For ideas of what it can mount look at Sneak's model and its remixes:…
This is a top corner mount for the Wyze Cam Pan v3. This part is designed to mount in one of the top corners of the Sumo enclosure for the Prusa XL, or the DELACK enclosure. The hole for the nut insert has been removed, and replaced with…
Instead of looking all over for a side cutter I like to have one handy - this serves that purpose
The is a DELACK Upper Corner Bracket with a larger Cable slot. Slot is 3.5x5.5mm. Fits the Buddy3D Camera cable. Everything else is the same.
The Delack enclosure is great but my printer is placed on a concrete paver and then raised on noise isolation feet. On top of that I am using the Delack light which skims a bit of the top space. So I needed to set the enclosure higher, so…
While printing things with higher bed temps, my enclosure gets a little too hot for my Prusa MK3S+'s liking, so I like to keep the door open. However, mine swings straight out and gets in the way. This clip allows the door to stay ALL the…
Merged the DELACK Enclosure Skirt and the Wyze v3 Holder together to have a bottom-mounted Wyze camera with the DELACK Enclosure skirt.
Remix of DELACK front LCD skirt wall that fits the "3x12sT" special screws. Main changes are the enlarged screw holes in the back to fit the special screws head used on the MK4S xLCD assembly. Use print settings as suggested by 3dsourcerer.
A basic adapter with two parts to allow for a PC4-M10 quick connect fitting to be mounted on the DELACK enclosure using the ports on the top cover. Useful for bowden tube setups when using the DELACK enclosure. Screw your quick connect…
I really like both Sneaks' articulated arm system and the DELACK enclosure. Coops combined the two for a top corner bracket mount. This is my attempt to adapt his model for a corner foot mount to have a platter level view for my camera.…
Just a modified version of the original that is mountable on the outside of the case so you can mount 2 hygrometers to monitor and compare inside and outside conditions. Got sick of my spare just sitting on top of the case and wanted it…
I've been using a Razer Kiyo connected to a raspberry pi as the camera for my MK4, and got the DELACK enclosure and saw the mounts for other webcams. Decided to quickly whip up a remix that would work for my Kiyo. The center hole didn't…
Mounts a Noctua PWM fan controller to a 3DSourcerer's DELACK enclosure.
2 files one file is the corner joiner and the other is the unifier (vertical side supports) block to unite each piece of plexiglass and reduce vibration sounds. Bonus file USB extension holder moves access to the USB port to the side of…
This is a replacement corner wall piece for a DELACK enclosure skirt which adds a small cutout for routing accessory cables. In my case I wanted to route a webcam cable at the front lower corner of the enclosure skirt. Print instructions…
This is my first attempt at a 3D model. I combined the Delack TP-Link Tapo Camera Mount with the Tapo Cam Mount for the C210 Pan & Tilt camera. So this should allow the C210 to be mounted inside the Delack Enclosure. I printed it out but…
No supports required. These corner covers are installed from the top down, so there is no need to move your enclosure to install them.
This is a simple plug for the LCD hole on the front of the DELACK enclosure skirt. Good for blocking air drafts through the hole when using an exhaust system and when not mounting a Prusa LCD on the front of the skirt. Leaves the option…
Delack Enclosure Feet Made these feet to raise the enclosure up about 3mm total vs the original rubber feet. Wanted to do this so that I could use a compressed air can to blow out the fine pieces of filament that build up over time.…
When I first printed the nameplate with color change, the first layer was not enough to hide the color behind from bleeding through. I deepened the recess of the letters to get at least 4 layers of the first color on before the DELACK…
This door handle is an upgrade to the base handle for the delack enclosure. I wanted something larger that I could easily grab when opening/closing. This fits the same bold hole and fits the M5 nuts that come with the enclosure. I suggest…
This is the middle bracket on a DELACK enclosure with a cable holder for the Buddy3d camera cable.
Keeps your Alcohol close and convenient - for cleaning the build plate of course
I liked the idea of the dorsal mount for the MMU3 buffer on the Delack. It nicely organizes things in my limited space. The Delack MMU side mount just didn't work for me. This top mount is nice and I really appreciate how the tubing is…
Hole Filler for DELACK Enclosure on the top.
An adapter to attach a TP-Link C101 camera to existing DELACK enclosure corner mounts for a WYZE v3 camera. I had already printed a WYZE v3 mount but shortly after replaced my WYZE camera and rather than designing and printing an entirely…
I wanted to use the DELACK Enclosure with a skirt but didn't like the options of either leaving the LCD inside the enclosure which makes it hard to use or mounting the LCD on the skirt since I wanted to be able to lift the entire…
This is a Buddy3D camera upper corner camera mount for the DELACK Enclosure. Included three models to have cable to left side, right side or straight back.
This is a modified rear cover for the Delack with holes for the PTFE tubes for your MMU. You can mount it one of 4 different ways by turning it depending on where your buffer is. Seems to make the bend in the tubes less dramatic. This…
Česky Pro mojí novou Pruša MK4 jsem postavil kryt s vlastními rozměry dle původního modelu: DELACK Enclosure by 3D SOURCERER Nevyhovoval mi držák pro GoPro kameru v horním rohu. Byl moc vysoko, proto jsem jsem jej upravil pro možnost…
As I started assembling my Sumo Enclosure I checked my Ring camera cable and the AC Infinity temperature probe cable and they wouldn't fit in the channel for the alternate top corners.
This is a Upper Side Bracket for the DELACK Enclosure with Buddy3D camera cable slot. Slot is 3.8 x 5.5mm.
Slightly narrower hinge (1mm) to fix door alignment
Depending on how you configure the enclosure, you may have some permanently-attached cables (for lighting, a camera) that make moving the enclosure a headache. This part allows for containment of the cables so you don't have to deal with…
Made this bracket to hold my hydrometer and thermometer inside my new DELACK enclosure. Here's the device I have: https://www.aliexpress.us/item/3256804164633114.html I made the bracket so I could just use a longer M5 bolt in the existing…
Loved the model by @Elan_61043 but could do without the “ribbed for her pleasure” sides. I remixed it with the smooth corner covers as well as removed the extra hole on the bottom so it looked cleaner. I have the light bar attachment for…
Modified the DELACK design for a smoke alarm to be better for the type of alarm I wanted to use. I wanted a small, low profile alarm for my case so picked up this one: Smoke Alarm,10-Year Smoke Detector Battery,Photoelectric Smoke…
Made for this very nice bowden splitter >>----> https://www.printables.com/model/300273-bowden-tube-y-splitter-with-pc4-m6-connections/files Print in whatever you like with supports for the nub and holes. Installation: Simply remove a…
Print in whatever filament you like with supports for the holes.
These models are for those who want all of the features available from their Delack enclosure and MMU. If you are in a position where you have a need for your enclosure and want the maximum height I hope the files help. The assembly is…
This is a smoke alarm/detector corner mount for the Delack enclosure if you are using Photon's top skirt riser. It replaces one corner. All I did was combine two parts and cut out some area so you can get the smoke alarm in and out. I…
This is a corner container for DELACK Enclosure. Dovetail interlocking container to cover hold parts together. Container inside dimensions: 70 mm wide, 67 mm deep and 83 mm tall.
Started with the concept for the PTFE guide bracket from the Prusa MINI Enclosure, but remixed to go in place of one of the side corner clips on the DELACK enclosure. Just moved my Mini into the DELACK enclosure and am testing various…
Modular corner attachment to hold E3D Revo nozzles on the DELACK enclosure. Removable labels to indicate nozzle size. Storage slot for tweezers or skinny wrench. Used 0.25 nozzle to print the labels. Mind your tolerances - I had to file…
Vedení kabelu pro / Cable routing for: SUMO/DELACK Enclosure TP-LINK TAPO Camera Mount https://www.printables.com/model/572812-delack-enclosure-by-3d-sourcerer-compatible-with-p…
DELACK Door Holder Are you sick of your face getting whacked by the door while working inside your DELACK? Ever want to spend just a few minutes tinkering in there on a warm summer day with the fan on, only to have to keep your elbow up…
I printed it in Prusament PETG with no supports. I used 0.2mm layer height with 15% infill.
Print in whatever you like, I used sunlu blue petg with the default .2 speed profile on a MK4 and it came out great.
Just as the title says, a guide for 6mm O.D. PTFE tubing to enter the top of your delack enclosure. I originally tried to modify the nice model PGold had made here , but could not get the threads to not bind up when assembling/printing in…
The Aoqee can be flashed with Thingino (RTSP and ONVIF)
you need longer bolts and you have to make a hole in the rubber plug. notice tabs are glued flush with the bottom surface of the light to make room for the rubber plug.
Decreased the opening size of the back wall skirt piece.
I was looking for a small cam that supported ONVIF and RTSP, the Wuuk Y0310 can be flashed with Thingino.
I printed it in Prusament PETG with no supports. I used 0.2mm layer height with 15% infill.
CLICK HERE FOR THE ASSEMBLY GUIDE
CLICK HERE FOR THE ASSEMBLY GUIDE
Add extra space to your DELACK with this skirt print! Contains an option for an external LCD mount! PLEASE REMOVE ALL OF THE ZIP TIES FOR THE LCD CABLE UNDER THE PRINTER, OR THE CABLES WILL NOT BE LONG ENOUGH TO REACH THE LCD! If you are…
