Counting matching models…
For when the 1.2L 3d case isn't small enough. Important information and disclaimer (read): It only works with Deskmini x300 and the ID-Cooling IS-30. It will not be compatible with anything else. The IS-30 is not perfectly compatible with…
SmallFormFactor.net forum post Design features Smaller than original DeskMini case Increased cooling performance across all components Decreased noise/turbulence More aesthetic choices Filler options for de-soldered VGA systems (see…
Disclaimer: Experimental feature. Use at your own risk. Performance penalty of using m.2 (4 lanes) is approximately 5-10% up to the 2080ti/3060ti level . If you use a more powerful card than this, your “lane penalty” will begin to…
I remixed this model from the original Noctua design to fit into my Asrock Deskmini X600 with the Noctua NH-L9a-AM5 fan. It should be suitable for the AMD AM4 and L9i (Intel) version and Deskmini X300 as well. You just need 4x 20mm M3…
Alternative Cover with improved ventilation for your MinisForum DeskMini UM350 mini PC. Use “Cut_Lueftung” as a modifier object in your slicer to remove top and bottom layers so that the infill comes out. Use different infill settings for…
CPU cooler fan duct that forces it to draw cool external air. Created for the DeskMini h470 and Noctua NH-L9i.
The horizontal fit is rather tight, so expect to maybe have to sand down the walls a tiny bit (especially if you print at 0.2mm like me). There are also holes on the bottom to screw the Deskmini in place using the vesa threads (If…
A simple Fan Duct for Asrock Deskmini X600 with Noctua NH-L9a-AM5
Made a cover for my Asrock deskmini to look like a tiny 386 style computer. I printed in bronze (all I had at the time) and spray painted with primer and fossil satin paint from rustoleum. Category: Electronics
As asked I post my remix of the noctua fan duct for my asrock deskmini X300 case. I first added some holes so only 5mm of the original hole's depth is left and I can use 20mm M3 screws. Then I added some more cuts so I can close the case…
Asrock Deskmini (X300, A300, H110, etc) hat to install full-height (25mm) 120mm fan for better and quieter cooling. Compared to V1, hat gained 10mm but fan can be fully inserted, no side cuts to eliminate air leaks. Attention: Necessity…
Asrock Deskmini (X300, A300, H110, etc) hat to install full-height (25mm) 120mm fan for better and quieter cooling. Attention: Necessity of irreversible case modification . Fan compatibility tested: Noctua NF-A12x25 - compatible Noctua…
Introduction to this project: It is a case replacement for the ASRock Deskmini series STX motherboards. I needed a powerful desktop processor and yet in a compact form factor. The original Deskmini case was too large for my liking and did…
Modified right Side of DeskGo custom case for DeskMini Button Switch with 18mm on the outside
To optimize space on the table, I mounted my DeskMini X300 under the table. This avoids a lot of cables on the table. Simple model made with FreeCAD (files included). If you like it, please post a make and give it a rate.
SmallFormFactor.net forum post Design features Smaller than original DeskMini case Increased cooling performance across all components Decreased noise/turbulence More aesthetic choices Filler options for de-soldered VGA systems (see…
This bracket replaces the supplied VESA plate and allows the DESK Mini to be hung directly on a SKADIS board. The screws supplied can be used. I recommend printing the model upright with support for optimum layer lines. As the Deskmini…
This bracket replaces the supplied VESA plate and allows the DESK Mini to be hung directly on a SKADIS board. The screws supplied can be used. Update May 2025, after two years my mount broke when taking it of the skadis and i decided to…
