Counting matching models…
This custom-designed probe holder is made specifically for my Rigol DHO804 oscilloscope. It should work with any DHO800 series scope and possibly DHO900 series (need to verify). It provides a secure and convenient storage solution for…
A holder for the USB-C power brick of a Rigol DHO800/900 series or DB858(E) device to attach to the VESA mount on the back to clean up the wiring. The power brick and its USB-C cable are attached with cable ties… … and then the holder can…
This stand is a pair of parts (right and left) that snap into place on the bottom of the DHO800/900 oscilloscope to raise it about 4 inches and tip it back to make it easier to view. No screws or spacers needed, it clips firmly into place…
(English below) @vogon hat ein nützliches Modell einer Halterung für die Messspitzen der Oszilloskop-Serien Rigol DHO800/900 (S) entworfen. Mir war die Platzierung am Arbeitsplatz jedoch zu unflexibel, weshalb ich mit Zuhilfenahme eines…
Rigol DHO 800/900 Abdeckkappe hinten Jede Kappe kann separat weggeklappt werden. Filament: TPU PLA oder PETG geht nicht, da das Teil beim einsetzen gebogen wird. polymaker polyflex 95a
The new Rigol DHO800 and DHO900 series is great, especially because it can be mounted on a VESA mount. Unfortunately, this also means that the cables are often suspended without support. This provides support for all the cables, including…
I got a new oscilloscope recently and mounted it to a monitor arm on my desk and wanted something to hold the probes out of the way. I tried using NullSense's probe holder part and found that the probe holders themselves were great, but…
Rigol DHO 800/900 Abdeckkappe front Die USB Kappe kann separat weggeklappt werden. Filament: TPU polymaker polyflex 95a PLA oder PETG geht nicht, da das Teil beim einsetzen gebogen wird.
******* PCB for USB A plug temporarily removed due to an error ******* This is an enclosure for a 3 port USB extension hub to fit to a RIGOL DHO800/900 series Oscilloscope allowing three devices to be used with the single USB port whilst…
Description This is a slim mount for a 92mm fan on the back of your Rigol DHO800/900-series oscilloscope. It reduces the noise compared to the internal fan significantly and even lowers the temperatures by a few degrees. This made a huge…
This is a universal probe holder for the RIGOL PVP3150 passive probes that come with the DHO800 / DHO900 series oscilloscopes. The probes are held securely in place with a satisfying snap. Other probes with a diameter of around 10.5 mm…
The adapter helps improve airflow and device cooling under prolonged use or high ambient temperature. Designed to be installed without modifying the oscilloscope — it uses existing screw points and aligns with the stock vent grid. Fan…
4.3U 19 inch rack front panel mount for Rigol DHO800/DHO900 oscilloscopes These panel mounts require the DAP 2U MP-1 bracket. This bracket must be cut in half, with the two halves moved 4.3U apart. Print the two halves of the front panel…
This model is a VESA spacer/adapter designed to be placed between an oscilloscope and a VESA mount plate . Its primary purpose is to restore free airflow around the rear ventilation and fan area , which can otherwise be partially or fully…
This model is a VESA spacer/adapter designed to be placed between an oscilloscope and a VESA mount plate . This is modified version of this model . Both models have the same mounts VESA75->VESA100 and look similar, but I tried add more…
This custom-designed probe holder is made specifically for my Rigol DHO804 oscilloscope. It should work with any DHO800 series scope and possibly DHO900 series (need to verify). It provides a secure and convenient storage solution for…
This is a universal probe holder for the RIGOL PVP3150 passive probes that come with the DHO800 / DHO900 series oscilloscopes. The probes are held securely in place with a satisfying snap. Other probes with a diameter of around 10.5 mm…
This model is a VESA spacer/adapter designed to be placed between an oscilloscope and a VESA mount plate . This is modified version of this model . Both models have the same mounts VESA75->VESA100 and look similar, but I tried add more…
Wall arm mainly for Rigol DHO800/900 but you can use it to hang whatever you need with vesa 100x100. You need just 4 bearings 608 and 2 screws M3.
Inserts for mounting a 92mm fan at the back of DHO800/DHO900-series oscilloscopes. The four pieces are just inserted into the hexagonal cutouts of the enclosure, from the inside. M2 bolts must be used, together with an appropriate M2…
This adapter can be used with fans having a body diameter of 21mm or less. To use it, cut the fan from the frame, trim the existing supports back to the body, then glue the body into the printed part with a dab of superglue (or your…
