Counting matching models…
Spool ends for the AD5X to add numbers, shaped to the spool spindle ends. Useful to show spool number which are hidden once you mount filament. Original designer did a great job sizing the posts for the print to clip in to existing…
These are non-marring TPU endcaps that slide over the top and bottom of happymaker 's Adjustable Height Support model. The bottom prevents the base from slipping and the top prevents the part from scratching the lifted item. There is a…
Since Jevermeister's holder refused to fit my DIN rail (standard 35x7mm) I decided to remix his models. I decided to go for the following changes: widened the profiled hole for the rail itself shortened them so they will not interfere…
Don't we all know this problem? You're tying your shoes and suddenly the little plastic piece holding the string ends together, flies off into the sunset as you pull the strings tight. Oh no - the strings will start fraying and pull apart…
End caps for the MPCNC. To make the closed end caps for the frame aligned with the corners, the X and Y sliede-rails must be 4mm (2mm per cap) shorter each. Fits for 25x2mm tubes. Print instructions Print in PETG or ASA
Removed the magnet holes from the reduced height versions of the gridfinity collection for faster print times. I only edited the endcaps as those were the ones I needed. Also added two more endcaps (2x1 & 2x3). The models are very crude…
Included are custom FPS end caps for the Adventure Force Nexus Pro; previously sold on Etsy and now shared for free. Details EDIT: Newer batches of Nexus Pros appear to be using a slightly different spring supplier, so we now recommend a…
Crazy end caps for a 20x20mm aluminum profile for Nut 5 & 6 mm If you want a special version, let me know. I will create it for you Different versions: Normal, closed With hole in the middle for cable feed through Cap half round Cap round…
Suggested to me by Dave Rome of CyclingTips ( @romeandstuff on Instagram) when he noticed a similar tool in the CeramicSpeed hub bearing tool kit . The tool slips over press-fit end caps found on many hubs, especially those with 12 and…
This file is prepared for a Formlabs printer and have been tested on a Form3B+ with Grey v4 resin printed exactly as oriented in the .form-file. The .zip-file contains a .form-file you can open in PreForm.
To install, Unscrew the mag base. Then screw the new one in (super simple). The extenders are somewhat untested, let me know if there are any issues.
This is based on the very well designed Ultimate Kitchen Gridfinity - I've taken the f3d file for the solid base version to create only end caps and blank plates. Included are all combinations that with a 5x5 gridfinity space, which is…
I ordered these track lights from Aliexpress as a kit, sadly they didn't come with endcaps so I designed some up. One is just for closing off the end, the other has a hole for wiring. This is the kit I ordered:…
I wanted a custom height and solid bases for the Kitchen Gridfinity collection. I found a parametric remix with solid bases. However, it didn't include a parametric model for endcaps. To fix this, I modified the design to a parametric…
Another endcaps for 2040 extrusions. Press fit no screw needed. Printed with ColorFabb XT-CF20 4 perimeter 0,15mm. Frame from Blackfrog.PL Hope you like it
The end caps can be attached to square tube with dimensions 30 x 30 x 3 mm (edge radius 5.5 mm). Versions I have drawn two versions, one with a flat end and one with a pocket for inserting a slider pad (diameter 26 mm). without pocket:…
Endcaps for MPCNC 25mm (outer diameter) tubes with an inner diameter of 1.5mm
Specific implentation See Sune chair fix. Endless Endcaps This parametric model allows you to quickly generate endcaps, furniture feet, spacers, caster wheel inserts, etc. The sky is the limit. My own usages So far I have used this to:…
best printed in petg, or if you like it better by any means in abs no rafts, 100% infill
These endcaps fit well on a pipe with 74,5 mm outer diameter . I made them to use a tube as storage for photography backdrops. One cap is meant to be glued in place, though it is slightly tapered and was a tight enough fit on mine. I used…
These end caps are for 25x2mm tubes. They are available in a variety of hole sizes so that the control cables for the steppers can be passed through. There is also a blind plug. They are step files, so feel free to make changes yourself…
I use these to cap the handlebar ends of my flat-bar road bike. I make them out of a polycarbonate-polyethylene blend. With a shaft diameter of 17.2mm, they fit snugly inside my Deda Dritto handlebar. I use the standard-length endcap on…
Replace the stock plastic endcap on cheap RC screwdrivers with a simple cap that can be color coded or a thumb twirler cap. Uses a single M3 socket head screw to attach. I may have used a hammer on the end of my cheap RC screwdrivers, and…
Endcaps for the 25 mm stainless steel tubes of the MPCNC. Endcap if a cable should be put through the tube: Print two times the half endcap version. Endcap if no cable should be put through the tube: Print the closed version of the endcap.
This is a simple endcap for a 4S 38120 battery pack with the typical orange holder with pins. It includes egress channels for large-gauge wire as well as top and bottom BMS connections. I've included the Fusion 360 file so you can…
PSA, the thin one works great but can sometimes be a pain to unscrew. I added a hole for something like an Allen wrench to the keyhole version to make it easier. I will upload some more textured options when I have the time. lmk if you…
I added 60mm length to the drop for less light spill for my aquarium, then I created end caps to suit and joiners to stop light spill in between the 200mm lengths. Added 300mm length for 900 lights I printed with PETG on Ender 3 Max Neo…
Parametric endcap. Optional base and hole shape as square or circle. Or conical shape. Optional chamfer and rim.
Font and rear endcaps 2040 with groove for Y axis belt of printer Ender 3 (stock, non-pro).
I designed this for the Ender 3 S1. But it will also work with the Ender 3 S1 Pro and the Ender 3 s1 Plus
Multi-use endcaps, chair leg, rod protection. printed in tpu, layer 0.25mm, filling 100%, inner diameter 4 to 22mm.
Made these endcaps to replace the missing a broken caps on my Equipto industrial tool cabinet. Enjoy!
These are endcaps you can print to put on the end of a rolling pin which should leave a 1/4" dough height when complete. Inspired by a request from my wife for even-height Christmas cookies. You may need to adjust the center holes to…
RSEAT P1 SimRig Endcaps Foot Protector Note my other models for RSEAT P1! I printed the parts with: 0.2mm layer heights (Bambu Lab X1 Standard Profile@BBL X1C) 3 / 3 top and bottom layers 3 walls and 15% infill printed with regular PLA…
Assuming you've tapped your 2020 Aluminum extrusion, these endcaps use a M5 counter sunk screw to attach to the extrusion.
2019 Yamaha Wolverine X4 SE I made these with slots to add a wooden, painted tailgate to my SxS so I could mount a diesel heater, fuel tank, and exhaust to it. It's contoured to mostly match the trim it's mounted against, though it isn't…
The endcaps that come with the Sowilo Dotless 16 Aluminum Channel have 5mm holes, which are not big enough for the 20AWG 6-conductor cables that they provide. This is a reproduction of the endcaps for the channel with a round diffuser.…
General information At the end of 2024, I set up version 11 of Helmut Weigl's RoeTest . In the process, I created some 3D designs that I am making available to the community in this collection . You can read more information about my…
Printed in PLA, 0.2mm no Infill, no Support but used a Brim. Should also work well on PETG or similar material.
Mitsubishi Triton back bullbar endcaps, Bed Temp,50, Nozzel Temp,200, Infill,30%, No need for support.
This is a dead simple plug because I was infuriated with my set of FPVERA hex drivers only having their size etched on one side of the tool body. Additionally: I found out that the stock plastic caps are really flimsy and they just sort…
I thought the following design was decent because you can use bolts to attach the cover(s) - I am only using the front cover but you can mirror this model to use front and rear.…
I wanted to keep the EMT protruding from the RepRack bracket to a minimum, but still be secured. The existing options out there are quite bulky for my tastes, and they used fasteners I didn't have on hand. So I whipped this up real quick…
Hello, For my Roadbike with which I want to ride long endurance trips, I put on some Quick-Release Aerobars from Redshift. 22mm OD 19mm ID Since I have the SRAM Red and wired Blips, I designed some Endcaps for the Aerobars to be able to…
This is a set of two STLs to print one decorative endcap for the Aquatic Life T5HO hybrid light. The total length is just over 18" so I cut in two parts and print it on the flat end to avoid supports. You will need to drill/tap your…
This is a load tested bracket, I simulated a much higher load than filament would ever exert, my personal setup holds up to 13 rolls of 1Kg filament rolls, with the addition of more brackets it can be extended , The diameter of the rod…
Front and back grills, and endcap have been modified, so it now allows inserting 6x3mm disc magnets. Thanks to use of magnets, you no longer need screws to mount endcaps, which improves look of the printer. Endcaps are also easy to…
This remix numbers the endcaps 1-4 for the (Alaskan) 2m elements. Print two of each of the numbers and fit them on the antenna elements so you can easily reassemble them in the correct order
Mount a bike with a 142x12mm thru axle (most modern road frames, older non-Boost MTBs, etc) on the old Wahoo Kickr v3 (2017) Is it strong enough? I wouldn't print this in PLA no matter how solid you make it, and don't think PETG would be…
Just like my previous remix for RepRack V1, this V2 remix includes 20mm and 20.5mm versions for standard aluminum pipes available in Europe/Germany. 20.08.26 added endcaps.
This is a collection of some endcaps I designed for constructions based on standardised aluminium extrusion profiles, widely known as 4040 etc.. I found the original plastic molded caps to be too loose and far too expensive, so I…
I Had some holes in the end caps of my table that needed to be filled, so i decided to make them usefull! I made it modular, incase one breaks over time or i wanted to add something in the future. I plan on designing a holder for a set of…
The purpose behind this project is a hanger for filament spools. The end caps are needed to keep the PVC pipe on the hooks and the spools on the pipe. I've created 2 versions The first endcap version hangs on by friction. The second…
I designed these to provide a padded end cap for the SOTAPOLE 10 - protecting the mast sections both in transport and in the event of unexpected collapse. Printing with 0.4mm nozzle, 3 walls and 10% infill should give a tight fit and a…
Over-engineered end cap for a generic Roller Stand. I designed it to match the original caps, but that was probably not necessary. A much simpler design would probably work just as well. I printed it in TPU for flexibility. It squeezes…
A simple ruler hook for muliconnect systems
Front and back grills, and endcap have been modified, so it now allows inserting 6x3mm disc magnets. Thanks to use of magnets, you no longer need screws to mount endcaps, which improves look of the printer. Endcaps are also easy to…
This is based on the very well designed Ultimate Kitchen Gridfinity - I've taken the f3d file for the solid base version to create only end caps and blank plates. Included are all combinations that with a 5x5 gridfinity space, which is…
To install, Unscrew the mag base. Then screw the new one in (super simple). The extenders are somewhat untested, let me know if there are any issues.
The Wixey WR700 digital readout for saw fence positioning uses a an extruded rail for sliding the readout. The ends of the rail are open, so this design is for left and right endcaps to give it a finished look. It can be just pushed into…
Print two end caps, one grid. Inital assembly requires melting the corners of the grid to the outside the endcaps, to give a smooth even edge. 1 - for clearance in the pipe, 2 - to hold it together. 3 - I used hot glue as an additional…
I needed to fix my gutter and raise the downspout a bit. this is a random collection of items i designed for it. hopefully it can help somebody else the pipe is a PVC 1 ½" pipe with thick walls (48mm OD, 40mm ID) printed in PETG fusion360…
I needed a storage container for some carbon rods I bought, and the easy solution was to print end caps for a cardboard tube I had. After cutting the tube to the length I needed I inserted the caps in the ends. I made the bottom cap flush…
I printed mine in white TPU but every other filament should work fine.
I created these endcaps to enclose diffuser track that was cut to custom lengths that didn't perfectly match the cut lengths of the LED strips. These also afford more flexibility in dealing with the wiring side of the strip since the…
Remix of Cascadable Filament Spool Stand / Kaskadierbarer Spulenständer with tabs removed for fitment improvements.
Like the original author of this idea the basis was to avoid trips to the hardware store or purchasing expensive aluminum rods online which can be hard to find the exact dimensions. However, this version has screwable end caps. It is…
About this model I was helping a friend assemble some of these shelves from King's Rack when I accidentally broke one of endcaps, used to cover the sharp edges of the vertical beams at the top for safety protection, while using a rubber…
This is a remix of sn4k3's design . Main Features Increased height to support BMG direct drive setups Added encaps for Smokyjoe's Led Bar Cut holes for cable management on both ends Screw holes for M3*12mm bolts What to print 1x Left 1x…
Hi, wanted to remix a file that looks basically the same but as i seen that the fit was just horrible, i decided to redo it from scratch, so not a remix anymore :D the fit is perfect for me ! There is multiple left side: one with a hole…
I inherited an Origin8 MT-3100 hub, which is a front 15 mm thru-axle hub. Interestingly, this is a "flush-axle" hub, meaning that the hub axle is nearly flush with the end faces of the hub. The effective "OLD" is 78 mm, making it…
This is a set of endcaps I created for a Meanwell HRP-300-12 power supply. The terminal endcap was designed to accommodate an AC power entry module I sourced from Mouser that provides an all-in-one plug+switch+fuse solution. Additionally…
This is a set of right and left endcaps for the LED light strip bars, They go with the AO-10x / Mendelmax bracket set that I designed, but may also fit Flurin's brackets potentially. Uploaded a 5mm wider mount and 8mm longer endcap module…
I wanted a endcap for my HEX screwdrivers from Aliexpress. First I printed model https://www.printables.com/model/418521-hex-screwdriver-cap but Unfortunate, my screwdrivers are a bit smaller. I could just have scaled it down,but instead…
The rings can be scaled to fit the Inner Diameter of the PVC pipe (currently scaled to 103.8mm to fit 104mm ID PVC Pipe). This provides a larger support surface for the dome to sit on, instead of trying to glue on the thin edge of the PVC…
This is a quick follow up to my earlier design for 22mm tube. I've just been donated some 15mm, chrome plated, copper plumbing pipe. Roughly 6 Inches, to be exact! So I decided to see if it would work as well as the 22mm tubing. Plus...…
Extended version of endcaps with covered back with M6, M5, M4 size
Hey! Look! Endcaps! Comes in Radiused and Square Corner Versions. Want only a center peg? We got that! Want 2 T-slot pegs? We got that! Want ALL 4 T-SLOTS PEGS!? … Yeah, we got that to! Description There are 2 faces available: square and…
Uploading because of request in comments for original file This is endcap for pipes / rods that are smaller than those suited for Filament Shelf Bracket model (https://www.printables.com/cs/model/556080-filament-shelf-brackets) This one…
The “Gothic Spaceship Wreck” terrain set by Terrain4Print is an amazing set, but for some pieces, I wanted end caps for pieces of wrecked hull section that, while still looking natural, weren't as long and tapering as the ones provided.…
About Hex Screwdriver Endcaps Upgrade your Hex Screwdriver Set with these stylish and functional endcaps. Designed to streamline your workflow, these endcaps feature a color-coded system for quick and easy size identification. Key…
