Counting matching models…
Like my other two versions (the picture shows actually the TBS SourceOne version) an antenna mount for the 2.4GHz ExpressLRS T-Antenna. The holes have a diameter of 5mm and the distance (center-center) is 24mm. Should fit on the standoffs…
I designed this adapter since I wasn't satisfied with the online available ones. I am using a Nazgul5 V2 with its XL5 V5 frame and an ExpressLRS 2.4GHz T-Antenna by HappyModel. To get the antenna into the printed part you might have to…
two types of antenna mounts ExpressLRS
Printed template for DIY small 868MHz / 915MHz antenna. Total size 26x6mm alternative to 160mm dipole. Use 0.7mm wire to make the antenna spring. Use coaxial IPEX4 antenna cable, solder active, central wire to the spring (no passive part…
Basic mount for the T style 2.4GHz dipole antenna that comes with the Radiomaster RP1 & RP3 ExpressLRS receivers. This design uses M3 heat set inserts with a hole spacing of 29.5mm & is designed to mount flush against a 3mm thick piece of…
elrs vertical mount hole is 6.1mm length 25mm you can modify it
A small and lightweight mount for the 2,4Ghz Happymodel antenna on the BabyApe Pro.
This is a collection of antenna mounts for the ExpressLRS 2.4 EP1 receiver from Happymodel that I designed to use in my TBS Source One frame, but I guess they work in any frame with 5mm diameter spacers. There are three options: Rear Vert…
It should fit for the frame. Couldn't try it myself, so I hope it works. ;) There are two versions. Their only difference is the orientation of the hex stand-offs.
ExpressLRS Vertical Antenna Standoff Mount for Betafpv or AxisFlying antenna 4/5/23: Added a slightly shorter version Category: R/C Vehicles
This is an antenna mount for the 2.4Ghz ExpressLRS antenna for the GEPRC Smart35. It can be used on the back or the front, depending where you mount your receiver and the length of your antenna cable. It may work on other frames but it…
This design is a combination of the front and rear bumper for the TBS SourceOne V3 integrated with my antenna mount design for the Happymodel ExpressLRS ep1 antenna. This design is also a remix of the TBS Source One Accessories but this…
The hex-holes have a distance (center-to-center) of 32mm. Apex Evo Update(2023-01-05): I uploaded a new version of this design which has 30 degrees turned hex holes. (Especially for Mark and of course everyone else whose stand offs are…
Happy Model Express LRS JR module enclosure. Clear Plastic LED 5V fan from Amazon . https://www.amazon.com/gp/product/B087Q8SDHB/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1 I used a 5v voltage reg for the fan to avoid magic smoke…
This design is a mount for the small 2.4GHz T-antenna of an ExpressLRS receiver. Similar to my other design: TBS SourceOneV3 ExpressLRS The holes for the standoffs have a diameter of 5mm and the distance between them is 22mm.…
Holds a VIFLY Finder 2 Buzzer and Betaflight 2.4GHz ExpressLRS receiver between the 5mm standoffs (32mm apart). There are two versions, with and without 2.4GHz antenna holder on the side. Optionally there is a bottom part which allows to…
For two SMA connectors and one ExpressLRS antenna on the back. Snip the two small parts on the ExpressLRS antenna pipe to insert it.
This is a remix and I wanted to have some protection for the antenna especially the vertical placed one. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.28 Filament: SaintSmart TPU RED…
For the AOS 7 frame, holds a 2.4GHz ExpressLRS antenna. Print with the arms upwards to avoid supports. Cut the small parts on the cylinder to insert the antenna.
There's a few other ELRS antenna mounts out there for this frame but none of them fit so I had to design my own. This one fits the 6mm standoffs that come with the frame. The beveled cuts on the top allow the mount to sit flush with the…
This TPU part holds the ExpressLRS receiver, beeper and vertical antenna on a iFlight XL10 frame.
868Mhz / 915MHz Antenna Dipole cover and mounts To get different angle mount and have antenna 10-15mm below bottom plate use lighter to gently warm-up printed handler . It will be much stronger then print of angled mount due to filament…
This is a simple expresslrs ep1 rx antenna mount for cidora SL5 V2.1 frame. And its a remix from https://www.thingiverse.com/thing:5341070 , as the original was not for cidora. So i combined the mount with cidora back bumper. Category: 3D…
Mounting frame for ExpressLRS RX for the Tron 80 whoop. Designed to fit the small square receiver such as the HappyModel PP, EP1, EP2 or BetaFPV ELRS Lite and so on. Plain cover if you have a separated antenna like on the PP or a flat…
A version of my ExpressLRS antenna mount design. Should fit for the TBS SourceOne V5 frame. I don't own one, so I had to rely on specifications and other uploaded designs for this frame.
My ExpressLRS R9M Fan Mod Cover https://github.com/ExpressLRS/ExpressLRS/wiki/R9M-Fan-Mod-Cover Print the ELRS Sticker!…
This TPU part holds the back antenna (2.4GHz ExpressLRS) on a iFlight XL10 frame. Print on the side (see pictures).
Requirements : Bandit Micro ExpressLRS 915MHz RF Module Tango 2 Antenna (you can buy it separately on TBS website among others) PLA/PETG Small file 1 - Assembling the foldable Antenna Remove the Tango 2 antenna original hinge : Tap on the…
GEPRC Vapor X Pro XR4 Gemini Xrossband Dual-Band ExpressLRS Receiver Front Antennna Holder
This is for the Happymodel EP1 and EP1-Dual antennas. As shown in the picture you can make a small cut to make inserting the antenna easier.
Hello guys, Kudos to @deft0nes for his design, I just modified it a bit to fit the v4 frame which has a different spacing. Category: R/C Vehicles
Didn't had much time so I've not tested it, yet. But it should work. ;) Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution: 0.2 mm Infill: 20% Filament: 3DWarHorse TPU
VTX: https://de.aliexpress.com/item/4000938942385.html RX:…
VTX: https://de.aliexpress.com/item/4000938942385.html RX:…
To securley mount an https://flywoo.net/products/0-4g-flywoo-2-4g-expresslrs-elrs-el24e-el24p Flywoo ELRS RX receiver on top of a Caddx Wlksnail VTX with a 20x20mm mount
16x16mm tray for EP1/EP2. I included a version with antenna protection for the EP2, but it is untested. Feed wires through the tray and solder. Wire guides on bottom route 2 directions. Print Settings Printer Brand: Prusa Printer: Prusa…
Quick and dirty remix of my dedicated 16x16 "gem" tray for HappyModel EP1 and EP2 receivers found here https://www.thingiverse.com/thing:4879612 Follow the link for more details that are also applicable to this design. I made this on…
This TPU part holds the back antenna (2.4GHz ExpressLRS) on a iFlight XL10 frame. Print on the side (see pictures).
![ExpressLRS R9M Fan Mod Cover [Official]](https://media.printables.com/media/prints/641774/images/5068867_89fee088-6a1b-4a2d-acd9-be35b766fc64_298d5351-09fc-415a-b94e-e283424284e4/large_display_r9m-fan-case-cover_641774.png)
