Counting matching models…
I designed this tool to make it easy to lift a silicone liner basket out of the air fryer. The liners came with little mitts that are awkward to use and tongs are no better. With this, you tilt it a little and slide one side into the…
A simple knob replacement for the Philips HD9200 Airfryer. Designed to fit the timer knob, but I think it would also fit the temperature knob. I used a sharpie to put marks at the 10-minute intervals. With the knob installed, the 0-minute…
Replacement handle for InstantPot Air Fryer Vortex 6. Printed using PLA on a MINI. Instructions for replacement. Remove the 3 screws holding the basket to the front cover. Remove the 3 screws holding the handle to the front cover. Change…
The 3D printed air fryer knob can be designed to fit a specific brand and model of air fryer, such as the Melissa air fryer. The design typically features a knob-shaped handle with a grip surface that is easy to turn, and a base that fits…
This is the knob for an air fryer model common in Brazil and that have poor default knobs that keep breaking.
Play Kitchen Ninja Air Fryer 2 Piece. not AI. Zero ai used in generation.
Pretty easy print. Take the silver ring part off the original knob and can insert it into the printed knob.
Knob do Timer Fryer Cadence FRT-555 FRT-560 FRT-600
The ribs on the circumference make the knobs less slippery. The original knobs are easy to remove. Help with a spatula. The steel leaf springs of the original knobs must also be used in the printed knobs. Fit the knobs so that the leaf…
Best to print this flat and use supports on the pegs that the screws go in.
The Instant Pot Air Fryer Lid includes a rack to add a second level for frying. Halfway through cooking, the lid tells you to rotate the food. Because the rack is very hot, moving it is extremely difficult. This tool lets you grab the…
The original handle cover broke due to a fall. Printerd in PETG (i think PLA could be more than enough), perfect fit. I think that this should fit other air fryer models but i didn't test it. Hope you enjoy :)
If you like, you can also peel the label off the original knob and stick it onto the replacement, as seen in the photo above
These knobs replace the factory knobs on the Farberware 45447 and may fit other similar models. The original timer knob broke and I wanted them to match so I made this set. The angle of the arrow is specific to the knob so you'll need one…
Tower air fryer timer knob. Also a shaft test print piece to check it fits before printing whole knob. If it needs to be bigger adjust percentage size in cura and export as stl binary file. Shaft hole size is 6mm d shape.
replacement air timer fryer knob
The frying basket of a kids cooker was broken so I designed and printed a stronger one. Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0,2 Infill: 20% Filament: Fil-A-Gehr PLA Yellow Notes: Use a large brim so that the…
Knob do Timer da Air Fryer Cadence
A simple replacement knob for my Ambiano Air Fryer since the original one broke. I also “upgraded” it since it was pretty hard to see the set time with the original one so I made a white indicator. It can be printed in two different…
Replacement handle and knob for Philco Black Gourmet Air Fryer - Model PFR15 . This is my first model, not perfect but fit por purpose. Feel free to modify and improve it as you please.
A replacement timer knob for the Best Buy brand Infinity Air Fryer. You can even reuse the trim ring from the original. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution: .18 Infill: 30…
Original knob started "slipping" when rotated, making it very hard to activate or shut off the airfryer. Decided to print a replacement if I could. Kudos to @Mich21050_518668 for sharing the f3d file so I could base my version off of that…
I've got an air fryer, but always struggle to figure out the timings. Someone sent me an image of this conversion, but struggle to find it on my phone half the time, plus my other half/son needs it to figure out too. So I tried making…
This model is made for the tupperware airfryer. Replacement for the original one. 2 screws must be demounted and reused. The cover has a snug fit. First unscrew the 2 screws of the original handle screw in the model Tupper_HF_Handle with…
The door mechanism broke and the company told me they could not sell me a replacement part. I would need to purchase a new unit. I tried to glue the part back together with JB Weld and a couple pins but it broke yet again. So… 3D printing…
This is a replacement handle I made for an older model airfryer. It's made in two parts to facilitate assembling the locking mechanism. Print both parts oriented upwards as in the model. Also print the button M3 inserts are needed so…
The handle on these ovens is exposed to the side and easily broken during shipping. This replacement attaches with the original M3 fasteners. Should be printed in a filament with some temperature resistance as the door gets quite hot…
This is a simple overlay for a PowerXL Air Fryer Oven and Grill. This includes a single sheet containing the Temperature, Function, and Timer dials with their markings as well as individual sheets for each. There is also a round design…
v5: added knurling to the outside Double check the slicing. Mine (SuperSlicer) had a gap between the outside and inside wall of the outer perimeter, with no filling. v4: has a smooth outside The fit should have no play but not super tight.
Quick and dirty adapter for aligning the gastro pan fryer basket in the CW1. This enables drying and curing with the fryer basket in the CW1. https://youtu.be/h2tb0qGyFAY Print instructions Printed with MK2.5 Prusa PETG 0.2mm layer height…
Da wir das Gerät nur bei Gebrauch aufstellen, nervte mich auf Dauer das Kabel. Ich habe eine einfach anzusteckende “Kabeltrommel” entworfen, damit endlich Ordnung bei Nichtgebrauch entsteht.
Original knob broke after a few weeks and before I knew about 3D printing it was fixed with some glue and heat shrink. It finally gave and whipped this up to have a proper replacement. Original knob broke after a few weeks and before I…
This is a replacement timer knob for my Daewoo 4L air fryer that I made after the original one broke. This is a quick print, taking only around 20 minutes on my AnkerMake M5C. It is quite a tight fit, so feel free to scale it up by 5% if…
Keep your kitchen neat and tidy with this simple and functional Air Fryer Rack Organizer! Designed to hold air fryer racks vertically, it frees up valuable counter space and keeps your racks easily accessible right next to your air fryer.…
Simple information plate Print Settings: Layer Height - 0.3 Infill - 20% Walls - 2
A tong to grab the basket. I burned myself a few times, trying to get it out another way. Not anymore. I also added Fuzzy skin to the handle, for the nice feeling Have fun with it
a few weeks after i bought the Farberware Air Fryer the release tab broke off, a simple enough piece. I made it out of PLA+ and no problems after 3 meals cooked in it. Category: Replacement Parts
A cute Airfryer toy. Maybe you have tou adjust tolerances to fit both parts.
Delimano Air fryer (LQ-2501) sliding clip from the basked handle. The original translucent clip was broken so I prepared this new one. Recommended print settings : Print with PETG or something more durable. Print with 0.2 quality layer…
Replacement knob with knurl for grip. Print Settings Infill: 90%+ (to prevent shaft receptacle from deforming) Category: Kitchen & Dining
This is a simple sulution to that problem that everyone has with their airfryer and downdraft vent, when you make fries or something else your intire kitchen will smell like it for the rest of the day. The FryFlow Redirect redirects the…
I've got an air fryer, but always struggle to figure out the timings. Someone sent me an image of this, but struggle to find it on my phone half the time, plus my other half/son needs it to figure out too. So I tried making this. My…
The original knob broke off, so here's a replacement for that :) In my experience the screw part is strong enough that it doesn't break off, if it does I guess just print out a new one → add superglue onto the surface of the inner…
Since my handle cover broke during cleaning, I had to get a new one. This cover fits the handle of the Princess XXL with 5.2 L. No glue is required, it should simply click into place.
I've got an air fryer, but always struggle to figure out the timings. Someone sent me an image of this, but struggle to find it on my phone half the time, plus my other half/son needs it to figure out too. So I tried making this. My…
I melted the factory supplied handle on my deep fryer, so I designed a replacement. It takes the M3 bolts and hex nuts that usually come with the Prusa i3 Mk3 kit. They are M3x10 socket head bolt and hexagonal M3 nuts UPDATE: added…
The handle broke on my 10 in 1 Ninja air fryer, so I modeled another one that uses the same screws as the original handle.
Voici 2 versions de poignées pour s'adapter aux 2 tailles de tiroir permettant un retrait sans se bruler des 2 moules en silicone. Impression en ASA conseillée Here are 2 versions of handles to adapt to the 2 drawer sizes allowing removal…
I've included a picture of the original white part that wore down over time. This replacement is designed for easy installation—simply unscrew the existing screw, place Part 1 behind the metal piece and Part 2 in front, snap them…
Replacement timer-knob for an AEG AF 5-1-4 air fryer. The original ones unfortunately break of very easily, especially when you manually turn back the clock to zero (you shouldn't do this) I printed them in PETG, 0,2mm, 2 walls, 4 top, 4…
I resized bottom side of the handle so it will have 20cm and also added a hole in the top part to make it possible to hang it :) Original text: The liners came with little mitts that are awkward to use and tongs are no better. With this,…
Ersatzknopf für den Timer der Aldi Heißluftfritteuse. Der Teil, der beim Original aufplatzt wird beim Modell mit 100% Füllung gedruckt.
Filament: ABS, ASA or PETG Layer thickness 0.25 mm Filling 25% Support: yes
Piece to prevent movement and fall of the fryer. Check that to remove the food tray, it moves, and may fall, with this support it prevents the sliding movement, and it can be moved without any problem by going up.
normalement s'adapte aussi aux marques Moulinex et tefal n'oubliez pas de poster vos photos de vos prints ça fait toujours plaisir !
A list of how to cook different things in a air fryer
Printed in PETG. I thoroughly tested it, and the handle stays cool enough, making it safe to place the printed part there. No support and no brim needed.
✔ Características: Cestillo extraíble con asa. Diseño pensado para imprimir sin soportes (dependiendo de la orientación). Escala ideal para complementar otros juegos de cocina infantiles. ✔ Impresión: Material: PLA Altura de capa: 0.2 mm.…
Decorative ring for the knob on Philips avance airfryer XXL Original decorative ring broke and fell off, so created this one as a replacement. 2 versions: One with the 4 little pins at bottom and one without the pins. I found the pins…
Four new feet needed for Morphy Richards deep fat fryer 0.2mm, brim only, no support and 100% infill Sumlu PLA Black
I bought second hand airfryer and the handle was broken so I design a replacement. Since it is not perfect, I have attached the step in case anyone is tempted to upgrade it. Compré de segunda mano una freidora de aire princess y la…
Our dishwasher ate the cap for our deep fryer's used-oil reservoir and I wanted to quickly throw something together to keep the oil from spilling out when moving the fryer. Unfortunately I didn't have any TPU on hand, which would have…
Hello everybody. My first contribution. In advance, I apologize if I missed any procedures. I use an Airfryer a lot. And as a cleaning practice, I use disposable aluminum pans to maintain the asepsis of the Airfryer's internal chamber.…
Home Is Where The Airfryer Is Funny sign to place at the airfryer Make sure to add the layer change to have the letters printed in a different color Not For Commercial Use
A replacement handle for Tefal fryer. The metal “hook” have to be replaced. The new model i designed for slightly larger head for the screw that holds the hook Printed with pla. 25% infill.
This is the STL download for the Foamarm Fryer Mag Holder. Print Settings Printer Brand: Anycubic Printer: i3 Mega S/Pro Rafts: No Supports: No Resolution: .2 Infill: 20 Category: 3D Printing
Switch Filler with LiPO cell check port for the Foamarm Fryer.
Quick replacement, not a perfect model, but it does the job just fine. Made with OnShape:…
test fit the adapter on the air fryer, it should be a snug fit, then remove, cut off the remaining connector on the knob and glue large cross shaped part onto it, then you can put the knob back on the air fryer
Magnani Italy airfryer handle
FOR FILAMENT DEHYDRATION USE ONLY. DO NOT COOK WITH IT. Turns a non-pro model instant pot air fryer lid into a filament dehydrator. These lids are cheap and can be found on fb marketplace/second hand. a 2 gal. bucket can fit 2 1kg spools.…
This is the STL for the Foamarm Fryer Extended Muzzle. This muzzle serves the function of pushing down sleeves that might interfere with the fired rounds otherwise, if you use the blaster with outerwear. -Rotate orientation in slicer…
Da mir die Schubladen mal runtergefallen sind, sind beide Griffe gebrochen. Habe diese nachgezeichnet und mit PETG gedruckt.
My cosori lite 3.8l air fryer needed to be cleaned, so naturally I spent my time designing and printing a jig to hold it when upside down in a convenient angle. This came out pretty nice. If you want to print one you have to mirror one of…
This is a replacement rotary knob for the Tefal Oleoclean deep fryer for setting the temperature.
This is a flexible anti-slip cover designed for the timer knob of the Midea Airfryer Oven , compatible with models FFA20P2 and FFA20P1 . The original factory knob has a smooth surface. In real kitchen use, especially after handling food…
This is a stand for the basket of a Taurus Air Fryer. I found it hard to store the basket other than inside the fryer. It has a square for the “basket-bar”, which makes it possible to place it on a shelf.
Replacement handle for airfryer. Consists of two parts. The first part is inserted into the handle lock and then screwed in using the original screws. The second part is then attached using 4x40mm screws. The dimensions of the lock are…
I needed a replacement knob. The old one was lost somewhere. PLA, 5 minutes print on Flashforge 5M. Infill: 15% Ghyroid internal print. No supports needed, brim advised 5 mm.
The release knob that allows you to detach the basket from the tray of our airfryer broke. I designed and printed a new one in ABS; 4 walls, 4 top and bottom layers, 40% infill. This is specifically for the Philips HD9252 airfryer, but I…
Voici 2 versions de poignées pour s'adapter aux 2 tailles de tiroir permettant un retrait sans se bruler des 2 moules en silicone. Impression en ASA conseillée Here are 2 versions of handles to adapt to the 2 drawer sizes allowing removal…
The original knob broke off, so here's a replacement for that :) In my experience the screw part is strong enough that it doesn't break off, if it does I guess just print out a new one → add superglue onto the surface of the inner…
Replacement timer-knob for an AEG AF 5-1-4 air fryer. The original ones unfortunately break of very easily, especially when you manually turn back the clock to zero (you shouldn't do this) I printed them in PETG, 0,2mm, 2 walls, 4 top, 4…
Original knob broke after a few weeks and before I knew about 3D printing it was fixed with some glue and heat shrink. It finally gave and whipped this up to have a proper replacement. Original knob broke after a few weeks and before I…
I needed a replacement knob. The old one was lost somewhere. PLA, 5 minutes print on Flashforge 5M. Infill: 15% Ghyroid internal print. No supports needed, brim advised 5 mm.
The release knob that allows you to detach the basket from the tray of our airfryer broke. I designed and printed a new one in ABS; 4 walls, 4 top and bottom layers, 40% infill. This is specifically for the Philips HD9252 airfryer, but I…
normalement s'adapte aussi aux marques Moulinex et tefal n'oubliez pas de poster vos photos de vos prints ça fait toujours plaisir !
Taller and wider than the stock part a more comfortable grip. Printed in PETG. Includes an inset hole for a hex nut. Sized to the nut that came with the fryer. STEP, 3MF, STL, and FreeCAD files availables Print Settings on Prusa Mini+ |…
The original knob is breaking when turned the wrong way. This is a common problem. This is a durable replacement that's not going to break either way you turn it. I printed it with supports on the bottom. Even if I'm not sure if they are…
I print with PC, seems a lot like the other knob, but I'm not sure they are the same.
The model works well printing in the exported orientation with tree supports. The photo shows the main body printed on it's back but I ultimately didn't like that. Might need to resize the drawers slightly depending on your printer's…
Best printed from ABS , PETG or similarly durable material resistant to higher temperatures as the heat from the air fryer creeps towards the handle a bit. My assumption is that PLA might get warped from the heat, but I haven't tried it.…
My air fryers keep slowly moving backwards on my counter whenever I close the cooking basket. These simple stoppers keep them in place (as long as I don't “shove” the basket). I have quartz countertops and just used some 3M command strips…
My air fryer stopped powering on, even though the basket was properly in place. When I opened it up, I discovered that sliding the basket in actuates a lever, which pushes in a normally-open switch connected to the mains. The part holding…
