Counting matching models…
Welcome to my first attempt at a printable kit of the Battleship Fuso in 1:625 and 1:700 scale. This model is based on the Fuso model in the game World of Warships, completely remodeled from the ground up, with many tweaks and adjustments…
You probably know all of these cheap lights that contain GU10 lamps. Most of these lights are kept very simple and can easily be converted to economical LED light sources. Compared to halogen spotlights, LED lamps not only have the…
Ein Schlüssel, für die Größen 18, 22 und 24, um den Perlator von einem Wasserhahn zu lösen oder wieder anzuziehen. Die üblichen Werkzeuge sind sperrig und nie zur Hand. Leicht verstaubar lässt sich damit schnell ein Sprudlerkopf vom Hahn…
The light of my Elegoo Neptune 4 Plus was a little to bright for my liking. So i desgned this. My recommended print settings: * 0.4 mm nozzle * layer height same as file name * 4 walls * infill doesnt matter * You dont need supports Happy…
A Diffusor for 8x8 RGB LED Matrix To be printed with two colors - Layers 0-3 with white PLA/PETG and the remaining parts using any other color you like. For best “pixels” a black frame is recommended. You can also print the entire piece…
printing with Layer high 0,08mm for best results.
A parametric LED Matrix diffusor front plate. fullcontrolXYZ based, 100%extrusion, 0 travel, 0 retractions. Extrudes at 0.8mm, which is totally fine for a 0.4nozzle. A bigger nozzle will probably allow much faster print speeds. Prints as…
A drink/bottle coaster diffusor with simple LED lighting. The goal was to construct a small housing for a LED sticker without support. I hope you like it. It consists of a lid and bottom that are held together with a bayonet catch. The…
This is a diffuser that can be used to evenly distribute the light from Philips Hue E27 LED bulbs. Other light sources may also fit inside. I originally made the diffuser for a triangular lampshade , but it also works as a stand-alone…
The Modell is made out of Transparent PLA its a Powerout LED defusor layerhight 0,3 linewidt0,6 speed 15mm/sec No Fan raft and VASEmode no Bottom and Top layer 8min of print KEEP windshielded with some paper
Wer den LED-Frame for IKEA SKADIS pegboards gedruckt hat und nach selbst geduckten Diffusoren sucht, ohne fummeln in die kleine schiene, kann die hier gern nutzen. Es werden die einzelnen Dateien wie folgt benötigt für die Skadis 36x56cm:…
Hello Makers, i wanted a bigger LED matrix with 32x32 LEDs. So i looked for a nice picture frame that fits also for the depth. I found a good & cheap one on IKEA. On Youtube there are lots of tutorials to build a 32x32 matrix out of four…
I came across this calculator for an acoustic diffusor and whipped up a basic static model of it: http://www.mh-audio.nl/Acoustics/DiffusorCalculator.asp They call it a skyline diffuser. Update 12/17/2022 : it looks like this link has…
Ein kleiner Diffusor mit Gardena-Anschluss, mit dem moeglichst viel Wasser mit geringer Stroemungsgeschwindigkeit punktuell zur Verfuegung gestellt werden kann. Nuetzlich z.B. bei der Bewaesserung von Baeumen und Straeuchern, aber auch…
I printed the Harry Potter Deathly Hallows Table Lamp ( https://www.thingiverse.com/thing:5617018 ) for my wife. To cover the light outlets I created these diffusers in TinkerCAD. Printed with 0.4 nozzle in concentric printing, first…
I want to have a led matrix to show information of my weather station. I first looked at the design from fractalnoise but one 8x32 matrix does not offer enough space. So I decide to make my own design. To have more space i make the design…
A simple and fast Solution for everyone, whose Desk or Rack is too small to reflect the RGB Status LED underneath the xLCD on the XL or the MK4. For assembly you can use the original two screws for fixation of the xLCD circuit board.…
Left some holes for magnets but mine actually fit without magnets. Not fully optimized, but it works and fits. Printed with Bambu A1 mini standard settings and standard PLA filament. Feel free to optimize material, design and print…
Another one? yes, another one… BUT! this one has a slot to slide in a (printed) diffusor, or a piece of paperstrip cut to the right specs. if you plan to use the gridfinity add on, you can print the file with gridfinity add-on, this…
Print in 99.5% size for perfect fitting. It's 0.6mm height, so it's 3 layers with .2 nozzle. Use polyester batting for non-pointing light.
Inner diameter is 14,61mm. Sealable by o-ring with inner diameter 13mm and cross section 2,5mm.
All calculations and the idea come from HiFi Audio Design . I made 2 versions of this Diffusor: one from 688 Hz to 8600 Hz (Bass) and one from 1147 Hz to 20 kHz (Allrounder). I know 688 Hz isn't bass but to effectivly diffuse sound with…
The first version published here is a rather minimal case with a surprisingly effective diffusor for one of those quadratic LED matrices you can get on Aliexpress with 256 WS2812b LED on it, 16 rows a 16 lights, spaced in a 10mm raster. A…
A 150x150mm example is included, to generate your own, you need to have openSCAD installed on your computer. Parameters should pop up on the right.
This Lamp consists of 3 parts: Lamp Base printed in reflective color (I used silver, white should work fine too) Lamp Shade its printed in vase mode to get rid of the seams printed with 0.6 nozzle for increased thickness print in any…
A simple LED rail with diffusing cover. I use it to recycle old led stripes. Soldered JST-XH connector. Used Prusament ASA for the diffusor with 0.16mm layer height and 0.24mm for the first layer. Snap-in design for easy creation of…
Print Instructions Material: PLA/PETG/HDGlass (Clear, See Through) Layer height: 0.2 mm or 0.15 mm Perimeters: 2 or 3 Infill: 15 % Supports: No
Led Diffusor Ring for the LED Ring Lamp A full ring with a small gap printed. Printed in white more transparent pla with 2 walls and 100% infill. Bend it on the gap it will break there and you can place it into the ring. Afterwards it…
Printed with TPU 95A 8% honaycomb infill, no supports needed if printed upside down
Alternative for those who hate the cold air outlet is always in their direction. I added extra fins to the air conditioner outlet sweep fin, thus directing the air coming out of the a/c laterally and independently.
a diffusor for daylight XXL LED Bars to avoid beeing blinded by the LEDS while working in front or in the printer.
Flashlight diffuser set (German below) Lantern diffuser Ball diffuser Signal cone Diameter is designed for the LedLenser P7R Signature Ø35.1mm flashlight https://ledlenser.com/de-at/produkt/taschenlampe-p7r-signature-502190/ But you can…
Please don't forget to give me a Like. :) Replace the tiny LED strip on your SV08 with an LED Daylight Stick (version for Voron 2.4 XXL stick 370mm like this one from aliexpress). The main model is for the right side of the top frame from…
I had printed the @perform3d version on my Prusa MK4 and XL and I really loved the very bright rendering. I then changed my MK4 to MK4S and printed the version of @hachleitner_1769169 which fits perfectly on the MK4S, but I found that the…
A small and portable macro flash diffusor for the Olympus 60mm f/2.8 macro lens that attaches on the bayonet mount of the lens. It allows you to still attach filters and close up lenses. It also fits the Olympus 25mm f/1.8 lens, as they…
I made a simple Diffusor Plate which gives a nice Glow for the LEDs Print it with white pla Filament Print with at least 2 Layers ! Structured Plate is recommended
Mounts the Vifly Strobe to the base mount without tape and at same time turns the 3 white LEDs to “legal” green for night flights in Germany which is far brighter than the single green LED on the Vifly. Works as diffusor which turns the…
Parimetrar: 2-3 Layers: Top/Bottom 3 Infill: No Filament: Clear
This is a model for a pond waterfall feature. It clams the water and produces a wider water stream. The box has a 19mm or 3/4in hose connector and internal walls to clam and distribute the water, creating a wider water stream to create a…
Parametric Flash Diffusor (Diffuser) Light Easy to print - no supports, no brims Clamps lightly to your flash Size and angle parametric Print in white or transparent filament. (Off-white filament will give your pictures a slight tint.)…
LED Strip Cover / Diffusor - 30 x 100mm When you have dark computer case and you want to see what is inside. Parts are 100 mm long and 30 mm high/deep. First I tested with smaller version and light was not good enough. When motherboard…
engish verion below Ich habe einen Diffusor für meine Amy-Shisha gesucht (Durchmesser des Tauchrohres: 20mm) aber nur Silikonüberzüge gefunden und aus diesem Grund selbst einen designt. Das Design möchte ich mit euch teilen. Ich habe es…
Upgraded bumper ( https://www.printables.com/model/1277060-rear-bumper-for-tamiya-tt-02-diffusor-for-yaris-ga ) Bigger diffusor for the TT-02 chassie with Yaris body Printed in TPU 95A with 8% honeycomb infill Protects the car and…
100mm long Diffusor that can be used with a LED lightstrip. It is printed in spiral vase mode with transparent filament. I used Vanilla White Prusament PLA to print it. Other colors and materials are also possible, please share your makes.
Just put a few drops of Essential Oil on the cotton stick and voilà. I made a version for vent with horizontal flaps.
Just a small and portable diffusor for Led Lenser P7R Just printed another one and got some pretty bad overhangs with 0.3 resolution. with 0.15 everything was fine. So maybe play with the resolution if you are not happy with the result.
difusor ajustado para imprimir en pla
diffusore posteriore per modello 1/10 gt
Since the original model always broke when putting it on the lamp I remixed it. Increased size to 102% to prevent breaking while putting the shade on the lamp doubled the wall size added screws for the diffusor as a design element → use…
I use this CO2 diffusor since some years in my 120cm tank. The water outlet on the top connects directly to a Juwel Eccoflow 500 pump head. In my tank, the diffusor and pump is installed behind a edge mounted hamburger mat filter. Outlet…
Check your leds temp, if they get too warm another version will be available soonish
Dimensions Inner diameter: 20mm Outer diameter: 25mm Hole diameter: 3.5mm Print Settings Printer: Creation Ender 3 Rafts: Doesn't Matter Supports: No Resolution: 0.1 - 0.2 Infill: 10 - 20% Post-Printing coming soon. Category: Replacement…
The lantern light diffuser is designed for an iPhone 15 Pro, but can also be placed on any smartphone. I printed it with a glow-in-the-dark filament. When the light is turned off, the lantern continues to glow. Perfect for any camping…
Printed it with PLA (Glow in the Dark) Infil 20% 0,2mm Layerhight 2 Contour lines Seems to be sturdy. Not fieldtested yet.
Die Idee Einen alltags tauglichen Luftfilter (mit Filter und leisen Ansaug-Geräuschen) konstruieren, welcher optimiert ist für eine Drehzahl oder im besten Fall für drei Drehzahlbereiche (tief, mittel, hoch) um das Optimum aus einem 2…
This probably works better as a diffusor, than a Dampening Panel. I thought that it might trap sound in the small chamber. Cant test it for myself because my printer is slow af :( but Ill be happy if someone uploads a make :) The…
Similar to the original but works with generic LED strips instead of the custom PCB. The strips can be up to 14mm wide and is slid in from the back, similar to the diffusor. To mount, choose one of the clips from the original and glue…
Simple LED Diffusor for Daylight on a stick v1.2 size for 350 voron !
If you print this with a red filament, you have a dual color diffused light and a white spotlight.
I remixed the LED diffusor/separator unit to fit the SMD's on the LED matrix. I used and scaled the separator from another great project - the matrix clock.
Piccolo diffusore per la barra led, va sistemato ad incasto.. stampato con pteg trasparente
Macro Flash Diffusor A simple attachement for the Nikon 40mm 1:2.8G DX Macro Lens. It allows to use the internal flash of your DSLR to light macro shots and is mounted on the lens hood snap-in-flange. (it snaps in like the lens hood) Why…
Ein einfacher Diffusor für die Olight i5T oder i5R .
This model is an addition to the famous original Prusa Printer enclosure (https://www.prusaprinters.org/prints/17-original-prusa-i3-mk3-enclosure-ikea-lack-table-pr). I have added this passage because it was a bit annoying at the…
I made the original a little bigger and added a Diffusor. The Diffusor was printed in transparent PLA and with no bottom skins. Hope you like it, pls post a make!
I added the diffusor directly on the matrix. My paper diffusor was not sitting nice and flush on the matrix. When I saw other matrices with integrated diffusor, I made this one for the mazerunner inspired clock. (Which doesn't need to be…
Easy light solution, when you are at dark places and need light everywhere. Maybe not fit on every phones, then try to measure and print it after. Print instructions Transparet filament Zero infill
PLA/ PETG / TPU -> transparent Works all fine, no support needed Ich habe die Originaldatei (stl) nicht mit hochgeladen, da die .3mf Datei so funktioniert muss nur gedruckt werden mit den Einstellungen. Mit PETG / PLA Transparent / TPU…
I needed a diffusor for the LED lantern lightning for my kids. I placed a 14000mcd yellow LED inside and it looks great. the bottom hole fits for a 5mm LED with a shrink tube Print Settings Printer: uArm Swift pro Rafts: Doesn't Matter…
I tried printing it in: PLA PETG Both worked with my 3W Bulb. Choose accordingly to the heat development of your bulb. Make sure your lamp doesn't get too hot!!!
A diffusor that can be used with the NiteCore MH12GT or any other flashlight that has a head of 25.4mm wide.
Made a simple Diffusor for a LED RGB Candle-Light in Tinkercad so it looks better in the modded little Halloween Pumpkin I also made. Easy to print. Maybe you must print it in 38mm (X/Y) size to fit better. Depends on how good you set…
To attach to fairy lights. With a head of 5 mm diameter.
Remix based on model from Stuff Maker
PLA / PETG / TPU -> transparent Works all fine, no support needed Update: Ich habe die Decke oben nochmal bearbeitet. Sie ist jetzt oben etwas Dicker. Der Druck hat sehr gut funktioniert mit TPU Transparent. Und sry ich hatte einen Fehler…
printed in PETG Transparent - only 3f filament needed 100% infill Mounted to the original LCD casing with double sided tape
I wanted to have a diffusor on my BOSCH GLI 12V-80 for better illumination of small rooms and spaces. Was a bit tricky to get the right shape and fit to make it look consistent and not to fall off. The protective cap was just a logical…
When trying to mount the original injection-molded housing of the MK4S xLCD to the original prusa enclosure there are several issues: the holes for the screws do not align the position is to high, the xLCD would block the doors. the…
Essential Oils Diffusor for AirCare Evaporative Humidifier Model 836000HBCN For the diffusor pad, you can use a small piece of felt or several layers of paper towels.
Soporte para colgar los difusores de pelo. el diametro interior es de 59, aprox todos son parecidos, en todo caso medirlo y aplicar la escala si fuera otro diametro. esta laminado con ideamaker con la funcion de textura Print Settings…
Turn your penlight or flashlight in to a handy camping light. Great for ambient light when camping or as a tool light for working on cars etc. Could probably be user for signaling as the “baton” lights upp pretty bright (depending on…
This is a stand with a diffusor for Neewer 176 (RGB) Lamp. It's a good and cheap light to take pictures of your 3D-printed projects. You need only 20mm bars (1.6mm thickness). Everything else is 3D-printed. This stand with diffusor can be…
Adding a diffusor cap for the Olight Perun. I used a (manual) color change after a couple of layers.
Empfehle rotes PETG im Vasen-Modus.
Its an easy to print adapter for your convoy S2+ or every similar lamp with approx. 24mm. The diffussor seperates the light to the side, so you can use it as a light on a table. When you print 2 of them, the lamp stands stable. When you…
Diffusor for the BLF Q8 flashlight. Printed with bq transparent filament, 0.1mm layer height & 30% infill for better diffusion. v1 is ~60mm high vs. ~110mm for v2
new diffusors for christmas https://www.printables.com/de/model/64058-spotlights-lampshade-v2-gu10-or-12-v-led-diffusor- You probably know all of these cheap lights that contain GU10 lamps. Most of these lights are kept very simple and…
Este modelo es un difusor del fleso de IKEA grande
Empfehle rotes PETG im Vasen-Modus.
This is for the following product from Action: https://www.action.com/de-de/p/3217439/led-pixeltafel/ I didn't liked the look of the display so I designed a thin diffuser an a thicker frame to make it look like a picture frame. The…
el difusor el tamaño va a gusto cambiándolo a escala va con regulación en el archivo puse los tornillos pero lo ideal cuando se imprima a escala ponerlos de hierro
I needed dual color led and the stock RED diffuser was replaced with one printed from transparent PET-G.
you can put leds inside or tape it on a alredy existig lamp. To the print: the difusor box must be printed in vase mode and in white or gray fillament. the on air sign must be so thin that light can get trough if you want you can use my…
Probé otros difusores ya compartidos por la comunidad, pero no me convencieron al 100%. Noté que el flujo de aire disminuía mucho y no era parejo en la mayor superficie de la cama caliente. Por lo tanto, decidí diseñar mi propio difusor,…
Sorgt beim Zehner Luftauslass für eine Ablenkung der Luft zur Seite. Rechts/links frei waehlbar. Unsichtbar zu verbauen.
designed for Zebralight SC600, but can probably adjusted for a lot of flashlights. printed with 15% infill. Recommend material: PETG or TPU
