Counting matching models…
Print in TPU, if its not a well calibrated print then expect very minor vignetting. This model is pushing the edge of vignetting. Install with 3 self tapping screws into the case. These screw holes were designed intentionally super small…
Screws together with M3 Screws (brass inserts required). There were other models that did similar things, but they were too flimsy and didn't have a good print orientation.
This mount is made to attach to round helmets or round surfaces, use epoxy glue or 3M double sided tape. I made the bottom surface perfectly round with a radius that matches my Smith Scout ski helmet. Print with normal supports and sand…
Created this for our training department so that they can organize our gopros
Testing. Gopro mount for saddle rail. 7mm round and 7x9mm oval rail. I modeled this to mount CO2 cartridge under the saddle. 1x M3 OD5mm heat insert 1x M3 bolt 10~12mm 1x M5 bolt 16~18mm 1x M5 nut
This is a GoPro mount adapter for a successful Chinese bike light sold under several brands. Note that the style of the slide mount has been updated at some point, this is the older style I believe. The model turned out great, it slides…
Everyone who searched for a ND-Filter for the GoPro Hero Session (4 or 5) knows that finding a good quality but not exorbitant expensive Filter or Filter Frame is basically imposible. Therefore I made my own frame for a basic glass…
Schuberth S3 GoPro Mount I have designed this mount because none of the standard GoPro attachments didn't fit my helmet. I 3D-scanned the helmet to fit the curvature around the chin vent. It is attached with 3M VHB tape cut to shape. It…
Print in a suitable material that works for you. I chose PETG, but it shouldn't really matter. I used 2 key rings to attach the flags, but use whatever you have. This was designed very crudely in FreeCAD 1.0, I've added the FreeCAD file…
This adapter allows you to mount a sliding GoPro plate to a tripod with a captive nut. Recommend printing at a bit higher resolution (<0.20mm/layer) than you normally would, in order for the GoPro plate to print nicely at an angle. I used…
Hi, I wanted to share this Adapter to mount your Zecto Front 250 on a Gopro adapter mainly to mount it under your bike computer mount like barfly in my case (see pictures). Sorry, the rough/raw design, not optimized nor aero but…
Simple PopSocket mount with GoPro mounting system. Used with this https://www.printables.com/model/185322-modular-mounting-system-gopro-arms-customizable/comments
Credit for the teleprompter goes to KatzCreates: https://www.printables.com/model/90999-camera-lens-mounted-teleprompter
Hi Makers! Ball mount is incredibly weak on El Grande Gopro pole, made out of brittle plastic which breaks at first opportunity. There is no official spare part and the head can not even be easily removed as it is molded in the tube. As a…
GoPro Mount / Webcam mount for 3030 Alu Profile / 3d Printer - Staffa montaggio per profilo 3030 / Stampante 3D Suitable for: https://www.printables.com/model/1171796-gopro-mount-extension-estensione-per-gopro…
Gopro plate head with screw mount. Ideal for accessories which offer only screw mount. Ease the change from support to support using only clips mounts. Print vertical (for better strengh with layers orientation) with 3 perimeters, 25%…
Fits around the bar of 22mm diameter. Made to fit 8mm width (1 inch diameter) steel cable ties . Made a flat side to print-in-place without supports. Made it stronger. Made it longer. 2 models. 3cm & 6cm from bar until gopro screw. Prints…
GoPro mount for backpacks. This particular design was made on request, it has a closed strap mount. There are two models Landscape and Portrait that rotate the orientation of the mount. The name is for identification mostly, it takes the…
a loop to replace tape or fastener to keep the batteries stay in the GoPro Dual Battery Charger . I need to charge the battery during riding. it helps keep the batteries falling out of the charger.
Designed in February 2025 to adapt GoPro-style phone mount to Fanatec Clubsport Wheelbase V2.5 for use as a dash and lap timer. Designed to be printed with no supports, prototype was made with 100% infill out of PETG. Overhangs in bolt…
🧵 Filament recommandés : PETG ou ASA 🖨 Conseils impressions : 4 parois Remplissage 10% Nid d’Abeille 🖥: Fichier STEP & STL 🛠 Accessoires utilisés : 2 vis INOX M4x14 2 écrous en T INOX M4 2 rondelles M4 INOX Support Go Pro montage sur…
This is a versatile grip mount that is compatible with every GoPro as well as any other camera that features a standard screw mount. Its design ensures a secure and stable attachment, making it perfect for capturing high-quality footage…
Support pour monter une box tools sur un sworks tarmac sl7, ceux dispo sur le site ne me convenais pas. l'angle de la fixation est parallèle au top tube. lien vers la box tools…
This is a GoPro mount designed for the Gear Photo Tripod by Thorin Oakenshield , with many thanks for the great original design. It replaces the standard 1/4 thread screw part. Required other than printed parts: 1x M5 Nut Print settings:…
GoPro 7 Rugged Case Insert - 3 Batteries - 2 Micro SD Card Holder - Extra storage space
This fan mount is designed for use with modular articulating arms, providing flexible installation for fans (e.g., PC fans, industrial blowers, or cooling systems) in various work environments. Features: Universal Mounting: Compatible…
i Wanted to attach my insta 360 go3 camera to my drone but it only has a gopro naked style mount. this mount uses 1 M5 nut and the screws for the Gopro naked mount.
This is a precisely modeled 3D printable replacement case for the GoPro Hero 5 Session camera. Ideal for restoration projects, damaged housing replacements, display mounts, or custom enclosures. Designed to match the original dimensions…
Gridfinity caddy for GoPro 11/12/13 Black and 2 batteries. There are other gridfinity designs for gopros, but I had a few requirements so I made my own: Stackable 6 units high to match other bins. It just barely fits! Can charge in place
GoPro Hero 8 Black Mount For FrameX - this has the side door closed off to prevent loss of the battery door - there is a cut out to push the gopro back out
GoPro Hero 8 Black Mount For FrameX - this has the battery side open to allow for access without removing the GoPro - Please note this can lead to losing the door in heavy crashes - ask me how i know
Print in TPU with supports from build plate only. no supports from the cleats on the bottom you can see they have a 45 degree angle to make printing easier Category: R/C Vehicles
I used TPE but any flexible material will work fine, the gopro lens is completely covered and with 10-15% infill it has come cushion from impacts. use a zip tie through the slot in the back to keep the gopro angled up. Print Settings…
Print all parts in the stiffest material possible. ABS, PETG, or PLA will likely be OK for light loads, but fiber-reinforced material (nylon, etc) is strongly recommended for any serious use. I used Polymaker glass fiber-reinforced nylon…
Fits the Nolan N60-6 helmet like a glove, you will need additional 3M VHB 4991 2.3 mm adhesive. For best results use PETG for added strenght and the following settings: 4 walls 45% Infill Enable support
Edit 1 : I have added a new support (v2), fixed between bed and spring for more stability. Original : This is a remix from ArduCam Stand : https://www.thingiverse.com/thing:1579435 I have replaced existing foot with an Anet A8 bed mount.…
Wanted to attach my phone to Gopro handlebar mount! Works great Sorry if something doesn't work its my first file
V3 OUT NOW! 21 millimeter barrel mount for any GoPro or action camera. Takes around an hour to print depending on settings used. I printed it on 30% infill, with .5mm thick top/bottom and sides. If you print it on higher infill, it will…
Wanted a simple mount to mount my Garmin Striker 4 fish finer to my boat. Was not able to find anything that attached directly to the Striker 4, so I design this. Works well and holds the Striker 4 very securely. You need to print either…
Eine Halterung um eine GoPro am Helm zu befestigen. Hierfür ist jedoch noch ein Klettband, eine Schraube und eine Schraubenmutter nötig. GoPro holder for helmet. All you need is a screw nut and a Zipper.
Loved the original model but didn't have the camera and had some unused Arlo cameras and a lot of gopro accessories so combined the two models. Fit perfect.
Modelled in Fusion 360. I made this lens cap cover for my replacement dive housing. I have a Hero 3 and purchased some underwater filters but later leared that they fit the newer style Hero 4 housing which has a smaller lens opening. None…
A camera canopy 3D design to mount GoPro mount style instead of the default smaller mount type. I have 3D printed using TPU but can also be printed with hard materials like PLA/PETG. There is no need for support material.
so the vision is easy, you put cymbal on the stand and than you will put some soft stuff on top of the cymbal than comes this mount. mount goes to the pin and then you can put some soft stuff on top or u just leave it as it is and put the…
as i promised i made nut for drums cymbal as a mount for gopro or any action camera. this one actually will replace original screw on your cymbal stand. it can work on gopro stuff but i used it with remixed model from @MReynolds
This is a rugged, low-profile camera mount designed specifically for the Traxxas XRT . Inspired by the T raxxas X-Maxx GoPro Mount v1.1 by JF_Chabot https://www.thingiverse.com/thing:2901055 , this remix has been completely re-engineered…
Go pro mount that suits Troy Lee design D4 carbon mitts helmet Print with PLA plus or materials that you trust to be strong. GoPro mount will print without support if your printer is tuned correctly. Orientation for print is flat on the…
Precision-fit GoPro mount designed specifically for the Nexx X.R3R helmet. The mount is attached using 3M VHB high-performance adhesive tape, providing a secure hold even at higher speeds. Printing in TPU is recommended to ensure optimal…
the M5 timelapse feature is so bad I made this jig that you need to mount on the bed. you'll get great timelapses. You need to remove the build plate mounting screws to mount it. and then the buildplate should slide in.
Just slice and print. I've used PETG for better durability, and lightning fill to reduce the amount of filament. Nothing special, fits all the items used to change angle of your GoPro Height is 9u, like all my go pro storage for…
Just slice and print. I've used PETG for better durability, and lightning fill to reduce the amount of filament. Nothing special, fits 5 batteries, with an easy fit Height is 9u, like all my go pro storage for consistency and box is…
3D-printed shock mount designed for slim condenser microphones (AKG P170-type / “cigarette” microphones). Uses elastic suspension to reduce vibration and handling noise. Designed around a GoPro-style mount for flexible positioning. Made…
Fit for RC18D RUNCAM Nano90 camera and analog runcam racer4 camera
Il y a deux versions : solid et ath avec deux versions de chaque pour pouvoir passer un strap ou non autour de la camera. Les versions "solid" sont inclinées à 25° ; 30° ; 35° et la version ath peut prendre les valeurs 5° ; 15° ; 25° ;…
An Action camera skateboard mount without holes for screws can be attached to the bottom of a skateboard using strong velco clips or you can use something else Let me know if something doesnt work and i will fix it
I have been inspired by https://www.printables.com/model/1309310-gopro-mount-for-leki-pole , however it did not work on my LEKI Trigger 3D handle, as LEKI redesigned the system for Trigger 3D handles. I have utilized…
A simpel stand for the GoPro charger and 4x Hero 13 batteries.
Use case These containers are made to hold one, two and three GoPro batteries of the size that work for GoPro Hero cameras up to Hero12. They aim to use as little extra space as possible in your baggage. They also secure that the contacts…
Go-pro attachment to mate with standard base accessories that can be blended to existing or new print models.
Box for up to 4 Gopro Hero 9, Hero 10 or Hero 11 batteries. This model is based on the "GoPro battery box" by Repoholy. I made it slightly bigger and added one more slot to fit 4 batteries instead of 3 :) Also I removed the GoPro logo on…
The semi-integrated cockpit of my new Endurace bike (CP0030) made it difficult to use some existing mounts, as the brake and shift cables were in the way. So, I jumped into Fusion 360 and designed my own solution. I’m using a Wahoo Elemnt…
Create 3D videos using two GoPro 10 cameras with this gopro holder. using two cameras mounted side-by-side (stereoscopic) to mimic human vision, or using a 360-degree camera like the
Use it with any of the original quadlock mounts (e.g. magsafe or charging heads) or print a basic one yourself. Supports needed. Printed with 0.10mm Layer Height, GoPro prongs pointing up. Pause at 9mm to add a M5 hex nut. 1/4 inch to…
GoPro Akku Box mit 3 Fächern für Akkus und 4 Fächern für Micro SD Karten.
This is a gopro compatible mount to hold an Exposure Diablo 15 bike light
I switched from GoPro to Insta360, and found that there were no organizers that would nest my camera well. So I designed one. Here it is.
The holder attaches to a desk or table. You can attach anything from the GoPro mounting system to it. I personally use this for a disc-shaped photo light or the DJI Osmo Action 4 camera. To print, you'll need an additional M5x20 screw…
Good to at least 50G shock with a 200g GoPro (100N), use at your own risk. Printing with 6 walls and 6 bottom layers, 8 top layers with ABS. Hardware: 3x M5x20 CSK 3x M5x20 washers
Ultra-low profile 3D printed mount built for action camera setups, including GoPro and DJI Osmo Action . Weighing an incredible 2.93g , it’s ultra-light without sacrificing strength—rigid, durable, and ready for real use. Its tiny…
Originally designed for Smelt dipping nets you can now mount a water proof Gopro to your smelt dipping net and capture high resolution 4K video of fish netting. Always be sure to use the Gopro clip expander to prevent any accidental…
Just a 45 I made really fast, print with any settings! (Preferably 0.2mm default) If you need to get a M5 Nut and heat press in!
Austauschdeckel, damit die Blue Bird Mini 25/15 Lux USB an einer GoPro-Halterung befestigt werden kann. Die Blue Bird Mini 25/15 Lux USB ist eigentlich mit Lenkerhalterung konzipiert. Replacement cover so that the Blue Bird Mini 25/15 Lux…
This is a reimagination of the "BrushRig" from stjame. I respect such creators but the price tag of the model was too high, considering this can be designed within two days. So consider this a free, less polished alternative. The freecad…
The Cover for the GoPro HERO4 USB ports will easily get lost so this designed cover will fit perfectly and look very much like the original. Designed to be printed in TPU and pressed into the USD ports on the side of the camera. Perfect…
use this gopro mount to quickly make an adapter for your camera or any other accessory use 2 part potty epoxy and mold the mount into it and the other side to what ever surface you wish
Basically a cover to keep your GoPro from scratches and dust. I have a GoPro 9 and 12 black which fits well.
Le modèle est gratuit, vous pouvez me soutenir ici : https://taap.it/nepty <3
print it in the orientation it imports in each hole will take 2 6x2 or 6x4 magnets make sure the magents are oriented in the same polarity
Hello tout le monde ! Voici un support pour la DJI Osmo Action 6 compatible pour avec les fixations GoPro. N'hésitez pas à me soutenir ici: https://taap.it/nepty <3 Hello everyone! Here is a mount for the DJI Osmo Action 6 that is…
You can print this on any 3D.Printer, just use UV resistance material like ABS or ASA PETG or so 3 walls 25% infill Use support just for the edge
The GoPro Mount works with an older Manfrotto tripod; I assume the newer ones use the same connection. It should also work with other tripods. Seeing that the camera mounts are universal. The step file is included, so if you want to edit…
Version 3 of the beloved barrel mount. Now low-rise to be sleeker and work better with newer action cameras.
To print rotate the front model upside down. Then it does not need any supports. Should be printable with any material if ~0.2mm tolerance is enough. Specifaclly made this to be able to mount a bike bottle holder to my archery bow stand.…
Hardware needed: 2x M5x9.5 Heated Inserts The Screw holes are 2.5" apart from another. Should fit most bottle cages and other stuff aswell. I printed it sideways, so some supports were needed.
This is a make for a typical GoPro mount for your bed plate. Made in a Flashforge AD5X, but compatible with mostly bed plates. Just slide the piece to insert it into the bed plate holder. Must be tight and stable. Printed with supports.…
Remix of https://www.thingiverse.com/thing:6401198 The beauty of this mount (as well as the original design) is that it mounts to the bed, keeping the print itself in a static frame of reference so you can actually get stable timelapse…
tip a tener en cuenta cuando lo laminemos es aconsejable poner el 100 % de relleno en los extemos que es la parte donde se une con la camara y es donde se le puede poner una correa y en el resto del cuerpo dejarlo con un 5 al 10% de…
