27 models
trg3dp published a SCAD file to create custom caps for beer growlers and gallon size jugs. I printed one of trg3dp's caps and found it could not seal fluids into the jug. I stated with trg3dp's scad file and provided further…
The Boeing EA-18G Growler is an American carrier-based electronic warfare aircraft, a specialized version of the two-seat F/A-18F Super Hornet. The EA-18G replaced the Northrop Grumman EA-6B Prowlers in service with the United States…
My Cura settings (settings with * are ones I've found to have a large effect on the quality of the print) Hatchbox Light Grey PLA *Temperature: 200 C Build plate temperature: 60 C *Layer height: 0.09 mm Line width: 0.4 mm *Support line…
Dive into modern electronic warfare with this 1:265 scale model of the EA-18G Growler, the specialized electronic attack variant of the Super Hornet. Built on the robust F/A-18F airframe, the EA-18G is equipped with advanced radar-jamming…
The uKegs from GrowlerWerks use CO-2 Cartridges of 8g and 16g but different cartridge sleeves are needed. If you have a 16g cartridge sleeve this adapter will allow you to use an 8g cartridge in the same sleeve. The hole makes it easy to…
Dry out those growlers without getting dust and crap inside them!
The frame is for The Float Life Drop-Top Fender for Pint. It fits right onto an XR Growler (with the official TFL Growler rails), and then the Drop-Top fits right into it. The frame should accommodate most common tires, though I’m…
Fairly simple cap, with dimples to help tighten/loosen. Also, for those folks who need it, a cap/pour spout combination. The reason I made it is that I flavor drinks with fruits, and didn't want the fruits coming out during a pour. With…
I took the super-useful original design (made by TheCase) and scaled it down - with some trial and error - to fit around a half-size growler (32-oz) mouth. Original (64-oz Growler size): https://www.thingiverse.com/thing:1122092 Print…
Where I live growler lids are not accepted for recycling. One evening I sat enjoying my beer while playing with a lid, and thinking about some way of reusing it. The first thing I came up with was this waterproof case, which is just a…
Printing this with higher layer heights (0.28mm) yields better fitment. My tests have shown this to be somewhat capable of holding pressure, and it is decently watertight. Category: Kitchen & Dining
M1161 Growler Internally Transportable Light Strike Vehicle Wall Art SIlhouette model. Adjustable size.
This is a simple drying stand for the ½ gal growler from homebrewing.org . Although the geometry requires supports to print, the stand is very stable and should provide a reasonably secure fit. It's great for drying after sanitization!
Did you break the handle on that great 64oz growler / water bottle you got at ALDI or maybe on Amazon? Use this model to print a replacement. The handle is attached to the growler's lid with a metal pin you can poke and pull out using a…
Designed these half fenders for a growler build they may fit the regular xr but I haven’t verified that. They were intended to be used without a fender delete and fit perfect with stock pads and 2mm ignite grip. print them solid with…
I purchased a 64oz Pressurized Mini Keg Growler, Portable Stainless Steel Home Keg Kit System from Amazon. It came with a bag to hold all of the accessories, but I felt it needed more. So I designed this case to keeps the tap components…
I was sick of my Growlers rolling all over the car when transporting them to and from breweries to get filled. This modular system can have as many growlers as you want, in any configuration. There are also stabilizers to go on the…
I picked up this growler from Amazon a couple of years ago and have never been able to pour my beer with 1 hand and hold my glass with the other so I either spilled the beer, ended up with too much head or both, so I made a handle for it!…
Prints ready to go for all your bottle-carrying needs. Just print it out and insert the wire part of the bottle into the groove (as pictured). It should snap into place. The model is designed to be printed on the side opposite the groove…
I got the Manna 64 oz growler with 4 cups from Costco and its great to be able to have 4 cups together with a large thermos. However the cups are quite thin and get a bit hot to hold without the handle so this solved my problem of burnt…
This tool is meant to help loosen the lid on Craftmaster Pressurized Growlers. Fits perfectly over the grooves of the lid. Print .2mm layer height, and increase perimeters to 4 or more for extra strength.
I wanted to use the growler fill tokens from a local brewery (Phillips in Victoria, BC) but couldn't find a parametric spinner that would let me use different sized weights instead of just identical bearings. I may have slightly missed…
Use a standard fermentation airlock with a 64 fluid ounce growler. Spaces for two o-rings, just use whatever you have on hand, ideally around 20mmx2mm
New and improved handle for the old, squat 64oz Hydroflask growler. My original was cracking at the corner of the ring so it was time for a new one. Required hardware: 4x M3x25 SHCS, 4x M3 square nuts Changes include: Thinner ring band…
I got the Manna 64 oz growler with 4 cups from Costco and its great to be able to have 4 cups together with a large thermos. However the cups are quite thin and get a bit hot to hold without the handle so this solved my problem of burnt…
M1161 Growler Internally Transportable Light Strike Vehicle Wall Art SIlhouette model. Adjustable size.
This tool is meant to help loosen the lid on Craftmaster Pressurized Growlers. Fits perfectly over the grooves of the lid. Print .2mm layer height, and increase perimeters to 4 or more for extra strength.
