Counting matching models…
To see how it works check out this video: The printing requires no special precautions, it works great with PLA. The inflator is best printed with the thick part on the plate. No support required. Please note the following tips: Use the…
I used 2 40a 4s escs with 2 5 inch fpv drone motors for power, along with a small servo for steering and a pwm reciever. The skirt is made from a trash bag and attached with duct tape, and it needs weight on the back to balance out the…
I designed this model to be large enough to work on multiple surfaces and transitions(grass, water, pavement, etc.) The hovercraft floats on water when the motors are off, thanks to the foam bumper and float assembly in the hull. Vapor…
This is a low detailed model of the SNR4 Hovercraft. The SNR4 was a type of hovercraft developed by Hovercraft Development Ltd (HDL) in the United Kingdom during the 1960s. It was designed primarily for commercial ferry use, particularly…
Hovercraft compatible with standard Lego or Lego Duplo bricks Complete your Lego or Lego Duplo collection with a new vehicle - a hovercraft! And print a cute toy for your children's - for example to make regular bath visits more fun :)…
I didn't like that I couldn't steer the original machine without it moving forward. I made these parts to fit the existing base and used a VTail mixer to get them to work properly together. With this setup I can spin 360 degrees with…
This project creates a fully functional RC hovercraft that glides over various surfaces , powered by electric motors and controlled via a standard RC transmitter . You can find the assembly guide in files. more at my Github . 1 main_body:…
There are a couple of balloon powered hovercraft disks out there. The advantages of this one are: easy operation: There's a mouth piece that simply screws off, so you can blow up the balloon through it and screw it on again without the…
To see how it works check out this video: The printing requires no special precautions, it works great with PLA. The inflator is best printed with the thick part on the plate. No support required. Please note the following tips: Use the…
This is a replacement housing to make a toy drone fly again. It works and has been tested by the children for its robustness;-) The drone's lights look even better than the original black one. The original folding mechanism to convert the…
I wanted to build a little hovercraft for fun and needed some way to clamp two of them to a bit of ply. This design provides such a design. I've added a slot for TPU to provide a tight fit. You can print this with no supports, but I…
I used 2 40a 4s escs with 2 5 inch fpv drone motors for power, along with a small servo for steering and a pwm reciever. The skirt is made from a trash bag and attached with duct tape, and it needs weight on the back to balance out the…
I designed this model to be large enough to work on multiple surfaces and transitions(grass, water, pavement, etc.) The hovercraft floats on water when the motors are off, thanks to the foam bumper and float assembly in the hull. Vapor…
R/C hovercraft with parts that can be printed easily, and mostly without supports. The hovercraft will require some basic assembly work. Below, you'll find the list of parts required, as well as some assembly instructions and some…
This RC hovercraft is a fully 3D-printed, modular vehicle designed for land and water traversal. It features two brushless DC motors—one providing vertical lift and the other driving forward thrust—along with a servo-controlled rudder for…
Tool to help marking the line for cutting the skirt which is 1.5i or 4cm away. Made for the Simple Brushless RC Sport Hovercraft made by Sir_Lancelot178.
Remix from original: https://www.thingiverse.com/thing:2783467 I've changed the motor mounts to support 0603 brushless motors (mine uses motors taken off my URUAV UR65). I have also made the holes larger to pass wires from the…
Demonstration and how to build: Small hovercraft designed for 1106 or 1104 brushless motors and 2" 50mm propellers. It was designed to be stable at high speeds with the right skirt and to be printed on a 200mm bed printer. With a 3s lipo…
Bumber stehend auf der geschlossenen / runden Fläche, kein Support erforderlich. Die Ruder ebenfalls stehend, kein Support erforderlich. PLA ist ausreichend, DRAFT oder SPEED.
I recomment a 0.2 nozzle for printing. If you want more content for Dominate & Delegate take a look at: https://dominate-and-delegate.com/en/downloads-materials Check also my collection:…
Full Build & Test hover video on Youtube: https://youtu.be/9EQT3OMNZYU Parts list: Electronics: 2x Drone Motors - Option 1 1507 3100kv: https://s.click.aliexpress.com/e/_c3gcpdFn * - Option 2 1606 3300kv:…
All the mechanism to create your very own hovercraft. Add some PVC piping for the leg structure and foam floats along with your choice of electronics and away you go!
I created an an EDF cover with the honeycomb built in to make slicing easier.
TAIYO EDGE R/C HOVERCRAFT propeller blade replacement
This is my edit of this hovercraft. I used Tom Stanton’s model and upscaled it by 200%. I designed a custom skirt in SolidWorks and sewed it myself. 6S setup, gyro-controlled. Definitely the most fun model in my RC hovercraft collection.…
This is a low detailed model of the SNR4 Hovercraft. The SNR4 was a type of hovercraft developed by Hovercraft Development Ltd (HDL) in the United Kingdom during the 1960s. It was designed primarily for commercial ferry use, particularly…
3D Benchy Hovercraft How does it work? It has a balloon adapter at the back, at which you attach an inflated balloon. The air-pressure is going to push the benchy from the ground and give it the hover effect. It also has two channels at…
this is a revision from my HoverWhoop -smaller and lighter -angled downward motors for more speed and centralized downward trust -accept both inductrix stick and eachine square battery Print Settings Printer Brand: FlashForge Printer:…
repurpose your old inductrix/e010 board to a fpv drifting hovercraft Print Settings Printer Brand: FlashForge Printer: Creator Pro Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 50 Post-Printing motor_holder.stl x2…
Motor mounts used for DIY RC hovercraft. Dual motor is with differential thrust 1804 size with 5030 props.
A simple balloon driven hovercraft, with large lip on the balloon tube to hold the balloon more securely. #Edit# I've started tweaking this in various ways. Version 2 now has separate directional fins that can be pressed in and aligned to…
This is a small sport hovercraft that is simple to build and decently fast and agile. Materials: 2x 1407 brushless motors 2x 15a brushless ESC 2x 3in prop 1x 9g servo 1x at least 2ch receiver 1x battery connector(I used an xt30) 1x 3s or…
Here is a short demo of the street glider https://vimeo.com/659992058 Note: You will need a printer with at least a print area of 290mm x 280mm in X and Y. This is the bare minimum size. Perhaps I will design some split models in the…
Update: V2 removed the impossible to print overhang on the bottom. Simple, fast to print adapter piece for building a CD hovercraft. I remixed this, due to faster printing and less filament use. Simply glue it to a regular CD and you are…
Introducing my new hovercraft print, powered by a balloon! This model is made up of two parts: the hovercraft itself and a screw with the balloon attached (you need a ballon). To inflate the balloon, simply blow it up through the screw.…
This is a Large RC hovercraft I designed because I wanted to use those cheap orange amazon motors(you know what im talking about) This should be printed as light as possible with 2 bottem layers and 3 top layers 2 walls and 5% infill. The…
Modeled after the Air Skimmer I made in middle school, I decided to recreate the model in an easily printable and reconfigurable design using OpenSCAD. Modify the OpenSCAD code and tweak the settings as you like. The hooks are used for…
Deutsch: Einfacher Tiny Whoov, es sind keine stützstrukturen nötig. Alles kann einfach zusammengesteckt werden, ohne kleben oder schrauben. English: Simple Tiny Whoov, no supports are needed. Everything can be simply put together, without…
Hovercraft compatible with standard Lego or Lego Duplo bricks Complete your Lego or Lego Duplo collection with a new vehicle - a hovercraft! And print a cute toy for your children's - for example to make regular bath visits more fun :)…
What is it? The is a hovercraft designed to be compatible with pup toy figurines from the popular children's series Paw Patrol. Big Version - Designed to fit all pups. Small Version - Fits the movie version of the pup (seen photo)…
Come support these models over on Patreon Buy my time, Not my models. Easy to print LCVP Higgens air cushion hovercraft, 1/100 scale, will want some greebling if scaled up. Some details have been changed for looks/ printability. The door…
Remix from: https://www.printables.com/model/333283-simple-brushless-rc-sport-hovercraft
Electronics I used are not mandatory pretty much anything works Motor:…
This is a large speedy and nimble hovercraft that is relatively easy to print, with next to no support material (≈50g of support). All parts are made so they can be printed on an Ender 3 or simular sized printer. The hovercraft is 580mm…
I didn't like that I couldn't steer the original machine without it moving forward. I made these parts to fit the existing base and used a VTail mixer to get them to work properly together. With this setup I can spin 360 degrees with…
Short run video: https://www.youtube.com/watch?v=K17ALo4rEuw Only the second run, getting the hang of steering. This is not full throttle as I'm still learning to keep it going straight. Another favorite toy of mine was the Typhoon…
Adapted RC hovercraft by Snowman to EDF 64. Please check his excellent details and video for more information. These are only the changed parts to fit EDF 64 instead of 70. REMARK: not tested. Waiting for parts. If you are brave enough to…
This project creates a fully functional RC hovercraft that glides over various surfaces , powered by electric motors and controlled via a standard RC transmitter . You can find the assembly guide in files. more at my Github . 1 main_body:…
Poweful Hovercraft Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Doesn't Matter Instructions Materials You will need: All the printed parts, a 2212 with it's speed controller, LI-PO battery, 9G servo, some…
Hello makers ! I would like to share with you the stl files that I modeled myself to make my RC hovercraft. It's really fun to use, it can do some nice acceleration and I had a great time making it. First of all I would like to thank…
