Counting matching models…
standard o-27 insulating track pin, inspired by another user who made the same. However I made this myself so I think original is okay??? correct me if im wrong. Sorry for the bad photos PLA 0.08mm layer lines default support type Make…
Edit: After doing this mod, I did some math and realized that it is really the width of the airgap that drives the effect of this mod. Therefore, the impact can be doubled or tripled by upping the gap from 1mm to e.g. 3mm or 5mm. I will…
This allows to screw a Suction cup with a M4 Screwterminal to other things. Either my insulating blanket as shown on the pictures, Or just use it as is, you can tie a rope to it. You will need: A suction cup with M4 thread. I used one of…
As we're expecting an unusual freeze at home my sweet, beloved wife pulled way too hard putting on a hose bib cover and broke the rubber retainer cord, rendering it useless. I drew up a pretty close replacement for it and shot a few out…
If necessary, you can scale it in the slicer. As a first approximation, the rule of three can be used. The model is designed with an inner diameter of of 58 mm. If, for example, an inner diameter of 70 mm is required, the scaling factor…
Replacement insulating boot for a 10mm (3/8") diameter steam wand. Filament: TPU 98A shore hardness Layer height: 0.2mm Infill: 100% NO SUPPORTS REQUIRED Note: if the ferrule on the end of the steam wand restricts the boot from pushing…
Insulating Tape Holder With Razor Blade is made for those who needs scissors to cut tape. Just put everything together with tape inside and enjoy easy cutting of the tape! Tape should have: Inner hole : 26mm or more Total tape thickness :…
Air Insulating Can Holder A comfortable and lightweight holder for a 500 ml can – perfect for barbecues, parties, and long summer evenings. It helps slow down the warming of your drink. I have tested the insulating properties and noticed…
Air Insulating Can Holder A comfortable and lightweight holder for a 500 ml can – perfect for barbecues, parties, and long summer evenings. It helps slow down the warming of your drink. I have tested the insulating properties and noticed…
This model extends the GridLink Genesis ™ system with edge parts sized to allow matching the Voron 2.4, 350mm panel mounting specification. I ran out of filament about 2mm from complete on my last batch, so 4 of the pieces shown in the…
If necessary, you can scale it in the slicer. As a first approximation, the rule of three can be used. The model is designed for an inner diameter of the roll of 33 mm. If, for example, an inner diameter of 40 mm is required, the scaling…
Seitenschutz für Isolierband mit Innendurchmesser 38 mm
Insulating caps for cable lugs Note: Used before connection to prevent contact with conductive surfaces. Sizes: 16 - 4 mm Fusion file included. .step file included
The model is designed for an inner diameter of the roll of 33 mm.
25-05-03: Bugfix for lager diameter.
A side protection for Tesa Insulating Tape to prevent dust accumulation. It can be easily clicked together, though a little force may be required. The inner diameter is 32 mm and the outer diameter is 56 mm.
Insulating DUMMY for batteries (SUT - small useful things) Break the circuit Fusion and step files included.
A multiple use Insulating Tab to easily disconnect a terminal of a 21700 or 18650 battery (select the correct model) from the holder. I hope you find this useful!
standard o-27 insulating track pin, inspired by another user who made the same. However I made this myself so I think original is okay??? correct me if im wrong. Sorry for the bad photos PLA 0.08mm layer lines default support type Make…
This is a replacement part for the Fontini insulating base plate (part no. 30-952-. ). Dimensions: 62mm x 1mm. Fits behind surface-mounted switches and sockets from Fontini. Print settings Filament: ASA/ABS/PETG Infill: 100% Layer height:…
This is a model for printing differently sized washers. The outer diameters and inner diameters are as listed on the files. It should be thin enough to flex for lots of materials. I HIGHLY RECOMMEND HAVING A SCRAPER TO REMOVE FROM PRINT…
Edit: After doing this mod, I did some math and realized that it is really the width of the airgap that drives the effect of this mod. Therefore, the impact can be doubled or tripled by upping the gap from 1mm to e.g. 3mm or 5mm. I will…
Works with RonCo stackable food dehydrator Model: 187-04 but I am sure it would work with some other stackable dehydrators. With the lid closed and fully stacked I was able to get to just under 78c. If you were to remove some levels and…
I was working on an upgrade to my Core One and lost one of the insulating inserts for the vent. I could not find a file for it so I made it! I used default setting with PETG and them seem to be working fine.
This allows to screw a Suction cup with a M4 Screwterminal to other things. Either my insulating blanket as shown on the pictures, Or just use it as is, you can tie a rope to it. You will need: A suction cup with M4 thread. I used one of…
Just the thing for hot days. With this insulated beverage can cooler, your drink stays cold for longer. Three internal air chambers running around the inside provide effective insulation. The cooler is designed to fit 0.5 L / 16 oz…
I originally designed this for TPU, but ended up printing it in PETG HF with excellent results. 0.16mm layers with 3 walls and 5% gyroid infill. The sleeve features internal relief ribs that provide a smooth sliding fit and reducing…
This sleeve for soda and beer cans provides insulation comparable to a foam holder, but much cooler (figuratively), keeping your drink cold but remaining warm to the touch. It's designed in OpenSCAD and extensively parameterized with 19…
Ham Radio Operators may appreciate this: This is a very simple print which I designed because I needed to put a UHF/SO-239 barrel through the wall of my metal trailer. The trouble is that the trailer has a lot of electronics in it, some…
This is a connector for the isolated connection of two H0 rails for the purpose of digital control.
Keeps can colder for longer This two-piece model is intended to provide a significant, insulating air space between your can and the warm ambient air, keeping your beverage cooler for longer. This can be achieved by eliminating infill, so…
Isolierkappe zum Isolieren von Blindstopfen an Pufferspeichern. Die Isolierkappe zusätzlich mit Isoliermaterial füllen und an der Isolierung des Pufferspeichers ankleben. Insulating cap for insulating blind plugs on buffer storage tanks.…
Model in Fusion 360 The cutting edge is made from an old hacksaw blade Print Settings Rafts: No Supports: No Resolution: 0,2 Filament: PM PLA red Category: 3D Printing
I didn't like the designs that were already present, so I made my own!
Insulate a M5 nut. The nut must be dropped in during printing. Used as part of my power distribution box . When the print is about 70% done. Pause the printer and drop the nut in place. You can inset a color change at the appropriate…
