Counting matching models…
I was in need of a second Lily58 low profile keyboard so I order a new PCB kit but to my surprise this time it did not fit my old case. So I adjusted it to fit it flawless. with this new version the Keyboard is 0.4mm lower as the previous…
Print approx. €0.43–€0.53 excl. taxPreliminary estimate for one variant
A travel “case” to let you take your Lily58 on the go! Fits 3D printed cases such as Lily58 Pro High Profile Case , Lily58 Case with 7mm standoffs , and Lily58 Case Requires 1 Plate, 4 Legs, and 1 large rubber band
Print approx. €0.76–€0.93 excl. taxPreliminary estimate for one variant
For the past year and a half, the Lily58 has been my trusted daily driver, delivering a gratifying typing experience. As the first mechanical keyboard I built, it holds a special place in my heart. However, most kits out there disappoint…
The 3D model is a case for the Allium58 GLP keyboard. The keyboard is modified from Lily58 Pro. The bottom case can also be used with other plates with 1.2mm thickness. Parts to be printed Allium58 bottom case Allium58 bottom case…
Uses any 1.5mm plate, including the 3d printed one here. Designed for the 3mm heat set inserts from McMaster.
I created for my Aurora Lily58 PCB Kit with MX switched from splitkb.com thie case. I used for the Oleds this Model: Aurora Lily58 Oled Housing PCB Hardware that I used Aurora Lily58 PCB Kit from splitkb.com with: RGB Underglow, RGB…
Required Hardware: Lily58 PCB kit & plate from any vendor (there are a lot) 10 x M2 heatset inserts (any should work) 10 x M2 screw 8 x 10mm rubber bumpers I screw my PCB to the case from above the plate, so I have I think 10mm M2 screws…
This is a remix of @Joshckb_190777 's excellent Lily58 case adapted to fit the Typeractive.xyz Lily58 Choc kit, which uses a more-compact switch spacing than the original Lily58 board. This only fits the Typeractive version of this board…
This replaces the bottom case of the Lily58 and Lily58 Pro to give 15 degrees of tenting. Uses the original standoffs and M2x5mm screws to secure the top plate to the case. Stick 5 6mm diameter adhesive rubber feet to the indents in each…
Lily58 Case with 7mm standoffs Print instructions 4 layers top 4 layers bottom 20% gyroid infill support as you wish
I was inspired by Coumbaya's Corne case to design this similar case for my Lily58. It acts like a bottom plate so you will need standoffs and a top plate to hold the whole thing together. I got my PCB and top plate from worldspawnkeebs on…
I recently built a Lily58 keyboard from Boardsource.xyz and wanted to print a case. I found the design done by Josh and really liked it. I ran into an issue where one of the holes did not line up with a hole on the PCB. It was close, but…
Aurora Lily58 Oled Housing to protect oled and customise your look. Should also fit the Lily58pro model or any other model that has an oled right above the rp2040 board. The housing gives more strength instead of flimsy floating piece of…
I couldn't find a 3d printable cover for the lily58's MCU. Which is … weird. But here's one now. IMPORTANT: The cover is not symmetrical. The hole placement on the board itself is strange and a symmetrical plate interferes with the…
Travel case for Lily58 Pro kit from mechaboards. Boards are facedown to protect keycaps, and held up from the bottom with small pillars. Made to be stacked on top of each other, so back of the boards faces each other. Held together with…
Acrylic Case for the Lily58 Pro. Specification 2x plates + oled covers 2x bottoms (optional) 6x walls for a low profile case or 10x walls for a high profile case 4x M2x9mm standoffs for oled covers 8x M2x6mm screws for oled covers…
This is a remix of the top plate of https://www.printables.com/model/93298-lily58-case to be compatible with the Lily58 kit from Typeractive.xyz as the screw posts do not fit the Typeractive variant of the lily58. This is strictly for the…
PCB Hardware that I used Aurora Lily58 PCB Kit from splitkb.com with: RGB Underglow, RGB Backlight Choc Hotswap sockets Microcontroller: Liatris Microcontroller Case hardware Aurora Lily58 Low Profile Case from splitkb.com : Top Plate /…
This is a case for the lily58 keyboard found on typeractive.xyz . It should probably work with other lily58 keyboards as well, but the USB port might need to be adjusted. It is based on another case that I use for my corne, but I don't…
remixed from Lily58 Case by waxpoetik and use pro micro covers from Lily58 Case by Josh Parts m2 countersunk screws m2 round head screws 7mm m2 spacers
I liked the case because I didn't had a plate for my Lily, but the legs were too much work for me and I also didn't had the screws :D So I removed the legs and pulled down the edge to act as a stand (including 4 degree tilt) Print…
Tenting base with M5 tenting holes to attach to the low-profile top piece of @Joshckb_190777's Lily58 Case Printed on my Flashforge A5M with Flashforge Burnt Titanium PLA using the Archimedes Spiral pattern for the top and bottom layer
This is a case I designed for the lily58 with choc spacing. I sourced mine from holykeebs (not affiliated). This case is designed to match (heights and design style) with a case I designed for the chocopad rev. 2 . There are two versions,…
This case I design houses the Aurora Lily58 from splitkb.com and has space for a 103040 Li-Po battery with 1200mAh. You will need 12mm standoff from the Plate, through the PCB to have enough space to clear the battery. I attached the…
Here's a remix of Josh's excellent Lily58 case.
Angled 40mm Cirque Trackpad Holder for Lily58
This design in based on this design and also inspired by this design. For assembly, You'll just need some 5 x M2 x 7mm screws per half and preferably a top plate and rubber feet for traction. I've uploaded with a range of tenting angled…
Simple base for the Lily58 keyboard . The STL file provided was created with the following parameters, which can be changed in the source .scad to customize it: clearance = 0.2; typing_angle = 7; base_thickness = 0.9; feet_height = 1;…
I designed this case on inspiration from profxwing 's Case for Choc Lily58 w/ 750mAh Battery (Typeractive) . This is simply a case for the Typeractive's Lily58 Wireless with space under the board for a 750 mAh battery. I have included the…
A case and plate for a handwired Lily58 split keyboard. Here is the GitHub repo from the original design. I built my version using a RP2040 Pro Micro. For interconnect I used DuPont connectors because they are very easy to find and they…
This is a case I designed for the lily58 with MX spacing. This case is designed to match (heights and design style) with a case I designed for the Tidbit 19 . There are two model files, the only difference is that one has the lily58 logo.…
This is a simple travel case for the Aurora Lily58 split keyboard. It uses magnets to hold both pieces together. Designed for my low profile choc lily58 case. You can check it out here:…
Couldn't find a display cover for the Nice!View on the Typeractive Choc Wireless set that worked. Fits well with the 3D printed Typeractive case or any alternative and just needs 4x M2x6 to screw in from the bottom of the PCB into the 3D…
Training Tool to learn columnar layout keyboards like the Aurora Lily58. Mirror it for the other side. Can be printed with some light tree supports for the overhangs, but wihout supports and some minor clipping should be fine too. Can be…
This is a travel case made for the Lily58 Pro Acrylic Case by BoardSodie. It is designed for the faces of each half to be encased and only the bottom exposed. This protects all of your precious keycaps from scratches. The two halves can…
Required hardware: 2 x M2 x 6mm screws. Fits well with this Lily58 case https://www.printables.com/model/93298-lily58-case I have not tested with any other variation of the Lily58 PCB other than Boardsource's modified Lily58.
This is a super easy print for a low profile case, with battery inset. If you want to use a bigger battery for your ZMK lily58, you can “hide” the battery in the case and enjoy longer battery life. This case also eliminates the use of…
I finally assembled my Lily58 keyboard that slept in a drawer for 4 years and I made a simple parametric cover to keep it safe when traveling. The extra room in front of the screen is for the battery cable. I use a Velcro strap to…
What you need: 4x M2 threaded nuts [ 2mm length ] 4x M2 screws [ 4mm length ] Glue [ for attaching the pad on the underside of the mount ] All parts printed in PLA with 100% infill. This is part of a project called NA_lily58 by…
Designed the case from https://www.printables.com/model/921084-case-for-lily58-with-750mah-battery . I printed these from PLA+. Listed is only one side, the other was simply mirrored. Cables from the battery are routed through holes in…
Split by Object. I used Triangle Infill, 15%
You may need to do some trimming around the screw holes to get it to fit right.
Lily58L Case With Light Holes and PCB Mounting Points. I used the DXF version on my CNC. 3mf included in case it helps anyone. Cover pic does not have top plate, but the picture with light blue does
Header Strip Female --- ATmega32U4 + pins --- 0.91 inch OLED Header Strip Female —
Aurora Lily58 spacers for low-profile case with mx hotswap sockets. If your keyswitches are not 100% pushed into their hotswap sockets you can use these spacers to push the entire PCB closer to the top plate holding the switches. Spacers…
Simple 15 degree tenting for the all of the cases for the Lily58 made by Gabbajoe . These legs will work on all of the cases listed below. Low profile choc case splitkb Lily58 (The case i am using) Aurora Lily58 Choc low profile case…
Made based on the Choc version of the Lily58 from the typeractive.xyz store. Not sure if it fits other Lily58s. You'll need elastic straps to thread through the slots in the model, and maybe some padding for the bottom that goes over your…
This is my project for Lily58 Wireless board typeactive.
A 3D-printable case set for the Lily58 MX , a popular 58-key split ergonomic mechanical keyboard. This case was originally designed for the PandaKB Lily58 MX , but it is also compatible with standard open-source Lily58 Pro MX builds that…
Hey, i remixed the Original to work with the great Case fom @Joshckb_190777 ( https://www.printables.com/model/93298-lily58-case ) Just print 4 Legs and 1 Plate and your good to go :) Ive glued two legs onto the plate to make the handling…
This case slides over the top of the typeractive.xyz keyboard. It does not use mechanical latches, as it is tight enough to stay on the keyboard on its own the keyboard case walls rest against narrow ledges on the inside wall of the…
I took CombatWombat_72384 's model and chopped the top off and mirrored a copy so that both halves of the keyboard can be combined in one case. Just as they said in their original description, this is simply a slip fit.
Tenting Legs for the Lily58 Pro mechanical keyboard. 10x M2x6m screws and M2 nuts 8x 10mm rubber feet
A snap case for Lily58 pro. It's got a little wiggle room, so maybe it can be used for other versions? Remixed from the one by LaGarna to add some extra space for a battery and remove the hex bolts for tenting, because I personally don't…
My G13 is slowly dying so I tried to keep somewhat the same feeling of a wrist rest with my Lily58. Even if it is the second/improved version I need to test it way more to check if it needs more tweaks. Important: My Lily58 keyboard uses…
Remixed from Sungo's cover. This narrows it a bit to fit choc and low profile case builds.
Hello, Welcome! This is my model for the lily58 split keyboard, I specifially tested this with the typeractive version of the board the fitment is around the nice!nano and includes spacing for the nice!view. This is my own design that I…
Description The Lily58 is an opensource column-staggered 58-key split keyboard. I wanted a versatile and portable yet sturdy case that is easy to transport, lightweight, hassle-free operation in different usecases (e.g. in public…
I Remixed the Aurora Lily58 Oled Housing to fit the Lily58 Pro from Kriscable.
New Lily58 Halcyon keyboard
I decided to create a Skirt knob for the Rotary encoder to fit the Encoder (EC11) that i have on my Lily58 Pro from Kriscables. You have to gently make a little pressure down for it to snug fit into the square bottom of the encoder.…
This 3D-printable model is a versatile travel case and ergonomic accessory designed for the Lily58 split mechanical keyboard. Key Features and Functionality: Dual-Purpose Design: The model serves as a protective travel case for both…
This is a remodel of a nice lily58 case. I had some issues with it, so I heavily remodeled it. The top plates need to be mirrored The bottom plates cant be mirrored, because of the thread for the mounting. You need to print the left and…
Modeled in FreeCAD (attached) and latest version can be found here. Attached files use the following parameters (purple print in the photos): Parameter Value Desc HasFeet no Disables feet location on the bottom StandAngle 15.0° Tilt angle…
I took CombatWombat_72384 's model and chopped the top off and mirrored a copy so that both halves of the keyboard can be combined in one case. Just as they said in their original description, this is simply a slip fit.
PCB Hardware that I used Aurora Lily58 PCB Kit from splitkb.com with: RGB Underglow, RGB Backlight Choc Hotswap sockets Microcontroller: Liatris Microcontroller Case hardware Aurora Lily58 Low Profile Case from splitkb.com : Top Plate /…
I was in need of a second Lily58 low profile keyboard so I order a new PCB kit but to my surprise this time it did not fit my old case. So I adjusted it to fit it flawless. with this new version the Keyboard is 0.4mm lower as the previous…
Print approx. €0.43–€0.53 excl. taxPreliminary estimate for one variant
Simple 15 degree tenting for the all of the cases for the Lily58 made by Gabbajoe . These legs will work on all of the cases listed below. Low profile choc case splitkb Lily58 (The case i am using) Aurora Lily58 Choc low profile case…
