P
Printables
Luckfox PicoKVM rackmount
just added a little wingaling to the side so it would bolt into a rack
Search results: luckfox
16 models
P
Printables
Case for Luckfox Lyra
Case for Luckfox Lyra, with a recess for a 2.1 power connector + hole for a USB cable.
P
Printables
Luckfox Pico Plus Case
Heres a case I designed for my Luckfox Pico Plus. Clips together and has a little push button for the Boot button. Pretty simple case but should do the job. Category: Electronics
P
Printables
Luckfox Pico plus - Sharkjack inspired case
I was looking for a case that was inspired by hak5 sharkjack and could not find anything. After no responses from hak5 after a few attempts to request official permission, I figured I would post this here, though if they ask I will remove…
P
Printables
FemtoBox - Professional Case for Meshtastic Femtofox Node – Perfect Fit for LuckFox w/ Foxbuntu – Supports I2C, Serial IO, USB-C OTG, Ethernet, and the High-Power 1W E32-900M30s LoRa Module (816MHz/915MHz) – So Stylish, Your Node Will Thank You!
This is my attempt at a very small case for the Femtofox Meshtastic node. More information on the Femtofox can be found here: https://github.com/femtofox/femtofox Some notes: Additional Components: N Female to IPX/UFL RG178 Cable - 10 cm…
P
Printables
Luckfox PicoKVM Wall or Desk Mount Shell Case
Case and wall mount for the LuckFox PicoKVM. Has cut outs for all ports and buttons. Uses 2.5mm screws for lid (Tight). Depending on the screws you are using to mount the box, you may need to use/print washers.
P
Printables
Luckfox Nova/Pico + RPI 10 inch rack, 1U
10 Inch rack for Luckfox Nova/Pico and Raspberry PI 3B 1U height Print Settings: Infill: 15% Gyroid Top: 5, Bottom 4 Perimeters: 3 0.2mm Structural
P
Printables
Luckfox Nova case and board
Luckfox Nova case. I printed it with PETG with a layer height of 0.3mm and a nozzle of 0.6mm diameter at pretty high speed; thus the look. As for the screws, I used 2x8mm self tapping screws.
P
Printables
LuckFox 7 inch touchscreen frame
I designed a frame for the Luckfox 7" HD touchscreen that mounts to the printer frame. The display is mounted on a carrier and can be folded towards the housing as well as completely removed if required. The design is intended for the…
P
Printables
Luckfox PicoKVM rackmount
just added a little wingaling to the side so it would bolt into a rack
P
Printables
Case for Luckfox Lyra
Case for Luckfox Lyra, with a recess for a 2.1 power connector + hole for a USB cable.
P
Printables
Luckfox PicoKVM 3.5 bay holder.
This is mod to allow pico kvm to be placed in a case with 3.5 bay. The size of my 3.5 bay is a bit different 103mm.
P
Printables
Luckfox PicoKVM Ext Expansion Board
A case for a Luckfox PicoKVM Ext Expansion Board including a dummy board and a lid. 4x M2x20 screws and nuts needed.
P
Printables
Luckfox Pico Pro/Max (RV1106) case & Pico Plus/Mini (RV1103)
Small cases for Luckfox Pico Pro/Max (RV1106) and Pico Plus/Mini (RV1103) You can add a piece of clear filament in the hole near the usb-c port to guide the indicator light through (for Pro/Plus/Max). There is also a version without the…