44 models
Case I designed to fit my Moondrop Chu IEM headphones. Could fit other headphones so long as the earpiece is smaller than 24 x 20 mm. I printed both standing on end to use minimal supports on the inner case and none on the outer.
Description The original case from Moondrop had an exposed top that offered no protection against losing the earbuds accidentally (while the magnets are strong, the earbuds can still fall out). I designed a case that is meant to replace…
Hard Case for Moondrop Space Travel. This is press fit case. Has notches for your fingers to easily remove the case. This is printed in PLA, but can be printed in any material any layer height. Notch also shows charging light. Print in…
Moondrop Chu 2 Wire Wrap Fits a small case like this https://www.aliexpress.us/item/3256806106169584.html Including models for the IEMs. They are not not precise, just meant to approximate the dimensions for the holder, so they are bigger…
I really wanted ear hooks for my Old Fashioned... but I couldn't find anything nice so I decide to give it a shot and design one myself. Printing Notes Make sure your printer is very well calibrated because We're printing small fine…
When I was searching for existing Models, I found bulky or full covering cases. It seems I've overlooked the version from GustyCadets, because his model is very similar to my Idea. I took a photo from the top as a reference and modeled…
I wanted a slider for my Moondrop CHU headphone wires so they would be more taut around my ears by allowing me to cinch the cables down under my chin. Took me 4 tries to refine, but the dimensions are tight enough to keep the cables in…
Moondrop Space Travel Charging Case Top Cover to avoid the IEM drop out from the charging case
Soft case designed for Moondrop DAWN Pro USB DAC. 3 versions with full cover, side opening or skeleton design. Updated: Test print with transparent blue TPU, 15mm/s, scarf seam.
See the other description for details. Since I removed the built-in support you have to add support for that part in the slicer.
Threw this together to fix the strap for a friend a few months ago. The hole for the plungers may be a bit under sized and need to be opened up slightly with a drill If needed I can work on a version with replacement ball spring plungers…
Replacement headband holders for Moondrop Para 1 The original ones have the screws going through the two posts in the center, and I did make a version that did the same, but I found that to break easily. So I changed the design so that…
I have printed this in TPU (95A) and PETG with default settings and it worked well with my material at those tolerances. It should extend down far enough that the clear plastic part of the case is totally covered. The sources are provided…
I create this model for myself and want to share with world. The axis is a piece of paper clip. And magnets with a diameter of 15 mm and a thickness of 1 mm were used.
I find it's easier to unplug the wires and store them in the included bag and then have the buds in this protective case! the magnets are 8x3x1.5mm
Use original screws to install this top Moondrop Space Travel 2 Custom Top Lid Version : Lower height than stock to make it easier to grab by stem. Snap on hinge, clip latch, no magnet. No-lid version : Very similar to the stock top,…
[No Longer Maintained] Reuse original screws for this lid The lid assumes you are using 5mm x 2mm magnets This design keeps the buds opened to reveal the sides of the buds to allow removal and insertions using the stems rather than the…
Simply slide on both pieces of the mount to your Dawn Pro and then drill two small pilot holes and screw in. See pictures for the screws to use(#4 x 1/2 inch wood screws). Updated file: V2 fixes fitting 4.4 cables better.
The axis is a piece of paper clip. And magnets with a diameter of 15 mm and a thickness of 1 mm were used. I changed the location of the magnets to open the window for the LED, and other minor changes. Inspired by the original case
Remixed model w/ thickened walls for additional strength/rigidity, and support for smaller magnet size (8mm x 2mm).
I modified the Koss KSC75 adapter pin to be used for connecting MoonDrop Old Fashioned cans to this 3d printable headband. See the remixed headband for printing / assembly instructions. Since these cans are thicker than KSC75's ones the…
Use Scale + - 0.5% for better fit, I printed with +0.5% for the body and -0.7% for the cap Don't need support but you can use it for the body part for better print Here is how the thread goes (example, you can do whatever you like tho)
A holder for of the Moondrop Space Travel earbuds case. It has a hole in the bottom for the usb charging cable. The “Heatset” version has a 4mm hole in the side to allow a CNC kitchen m3 heatset insert to be used so it can attach to…
A cover for the Moondrop Block earbuds. It friction fits snuggly over the top and prevents the earbuds from falling out. Simple yet effective. :)
I rounded the edges a little bit more compared to the original model, now with a 2mm radius. This results in a better UX due to less pricking. Images: left is original model, printed in black JAYO PLA. Right is my remix, printed in blue…
Moondrop Space Travel earphones are great but the charging case is mid. The earphones rattle out when you run for the bus, they get clarted up with lint and when you reinsert the earphones they can easily go in skew-whiff. You could spend…
This minimalist cable holder is designed to secure a USB-C cable (tested with a Moondrop cable) under a desk or shelf. It keeps your connector within easy reach while preventing it from falling to the floor when you unplug it. The compact…
A quick case I designed for my new CHU2's, it has a latched lid, and even has spare room for spare ear tips. It's very simple, only requires some raw 1.75mm filament to use in the hinges. I was heavily inspired by RagingPandabear's case,…
Designed for Moondrop Space Travel 2 Ultra Hope it fits Moondrop Space Travel and Space Travel 2 also Flex filament print, recommended 5 wals print, without supports it works I printed Gembird TPE (black part) and Bambulab TPU for AMS…
The case was designed in Fusion 360 for my Moondrop Pudding, I modelled it after the official clear case sold by Moondrop I printed this out of TPU 95A and the fit is good. The wall thickness is 1.2mm so I would suggest a linewidth of 0.6…
The existing case didn't hold the earbuds well enough, so we decided to use the The charging port short-circuits when traveling. So I made a case that can hold the earphones better.
The original case of evo is not properly fixed, so the charging terminal often shorts out. You can't carry it in your bag. That's why I made this case. After printing, assemble it, and then plug it into your existing charging station.
Made due to the frustration caused by how badly thought out Moondrop Littlewhite adjustable IEM cable is. I live in a warm and humid country, so the rubber-esque cable clip barely holds the cable position; making the setup unreliable and…
Just a nicer case than the cardboard box. Still uses the original plastic insert
A 17° tilt stand for MOONDROP MM3A desktop speakers. On a normal desk the tweeters fire at your chest; this stand angles them up to ear level (calculated for ears about 40 cm above the desk and 70 cm away). PRINT SETTINGS: Print flat with…
MOONDROP Holder for IKEA Skadis !Print with the name upside down! compatible with MOONDROP: MOCA SPACE TRAVEL SPACE TRAVEL 2 SPACE TRAVEL 2 ULTRA ULTRASONIC 26.05.26 Update: New design, less material, shorter print time. Support added…
worked on my uprint, but it has near perfect tolerances, print on 0.12 layer height or .20 quality layer height
I rounded the edges a little bit more compared to the original model, now with a 2mm radius. This results in a better UX due to less pricking. Images: left is original model, printed in black JAYO PLA. Right is my remix, printed in blue…
Just a nicer case than the cardboard box. Still uses the original plastic insert
Threw this together to fix the strap for a friend a few months ago. The hole for the plungers may be a bit under sized and need to be opened up slightly with a drill If needed I can work on a version with replacement ball spring plungers…
Replacement headband holders for Moondrop Para 1 The original ones have the screws going through the two posts in the center, and I did make a version that did the same, but I found that to break easily. So I changed the design so that…
This minimalist cable holder is designed to secure a USB-C cable (tested with a Moondrop cable) under a desk or shelf. It keeps your connector within easy reach while preventing it from falling to the floor when you unplug it. The compact…
Moondrop Space Travel Charging Case Top Cover to avoid the IEM drop out from the charging case
a 3D printable case for Moondrop Space Travel! Now you don't have to worry about the earbuds hanging out in the open anymore. The lid is held by 6mm x 3mm magnets Printed recommended in ABS, ASA or PETG, but PLA works the parts consist of…
![[deprecated] [v2] Moondrop Space Travel (1/2/Ultra) Lidded Case](https://media.printables.com/media/prints/0eb21669-21e5-4a60-a970-c86c194f1866/images/12818290_feb8c55d-5d75-41c7-bb68-8843fef34426_cc379d1b-d258-45c8-b44a-bc0f8f7d9da6/thumbnail2.png)
