Counting matching models…
Introduction: Electronic waste (e-waste) is a huge global problem, posing troubling environmental threats. Waste mobile phones are a big part of e-waste, mainly due to extreme demand & short product life-cycles. While older smartphone…
I disliked the original position of the little pwm hub in my fractal torrent since I would have to cramp a lot of cables in the bottom left of the case, so I decided to mount it in the center, where one 3.5" HDD cage used to be. This is a…
The Nexus 70mm fan seems to be a pretty common cooling upgrade for the original Xbox. The stock fan is a proprietary 72-ish mm job that has a specific shape and these tabs that secure it into the back of the console. However there is no…
nexus · watering can and cup this design comes in two variants, watering can (with a handle) and a smaller watering cup, in a modern minimalist style important · make sure that: your filament is dry and calibrated so that it deals…
For use with any other collet in the ecosystem (Xshot Longshot, Unicorn) Printable with no support, if the overhang is giving some problems, you can use some. This is functional with the stock barrel. The stock barrel measures (incase you…
Included are custom FPS end caps for the Adventure Force Nexus Pro; previously sold on Etsy and now shared for free. Details EDIT: Newer batches of Nexus Pros appear to be using a slightly different spring supplier, so we now recommend a…
Angled Pump Grip for the Nexus Pro X dart blaster. Hardware needed: Re-use 4 Screws from Original Grip. Optional: Re-use pin and roller from Original Grip.
Buffer Plate Sling Mount for the Nexus Pro hardware needed: 1 5mm x 20 mm bolt, with a head no wider than 8.5mm 1 5mm nut with 8mm wrench flats don't overtighten, your buffer tube is made of plastic Update: uploaded a .step file of the…
i used a m3 heat insert into the fake adjustment wheel to tighten the rear sight. source https://cults3d.com/en/3d-model/tool/ar15-m4-m16-a1-detachable-handle
cosmetic magwell. based on the one from out of darts.
Replaces stock barrel coupler and muzzle. Install by simply dropping into the blaster once the stock muzzle and barrel coupler has been removed. Intended to work with stock barrel only. This modification removes all indexing issues…
Attention: I keep seeing people selling these models on Esty and eBay: Digital files and actual prints. STOP THAT! I have already gone after a few of them and got them banned. I will pull these off here if this keeps happening. I put…
A hair trigger for the Nexus Pro and other similar platforms, since I felt that the stock trigger pull had a sloppy feeling. Added bonus in the trigger lock removal, that now enables You to safely de-prime the blaster. The safety is still…
Apple Watch stand that holds your charger, also works with AirPods Dimensions ⬝ mm ▪ Apple Watch stand - x:45 ⬝ y:60 ⬝ z:53 Print ⬝ Profile ▪ 0.40mm nozzle ▪ 0.20mm layer height ▪ 15% gyroid infill ▪ Outer walls slowed for print quality ▪…
Buffer Tube Sling Mount for the NeXus Pro X print support material strongly advised hardware needed 3x15mm bolt with head no larger than 6mm 3mm nut with 5.5mm wrench flats
Dart Zone (Adventure Force) Nexus Pro shotgun-like pump foregrip kinda a hybrid pump grip / angled foregrip note, the roll bar up front is a thumb rest. meant to be held with thumb angled upwards like a 'traditional' rifle grip, not…
I have invented a pair of adapters to be added to the sides of a NEXUS Rollator/Walker to permit the attachment of anything built with the “dovetail style” mounting. I have included a Cup Holder, a Shopping Bag Hook, a Carabiner Loop, and…
Basic spring spacer for the Nexus pro. Should be similar to the OOD Spring spacer in power. Can't test FPS as my Nexus Pro is modified with a different barrel than stock.
A Shortened Magazine Release for the Nexus Pro, Max Stryker, and Dart Zone Pro MK3 When primarily using half-darts with the magwell adapter, the main magazine release is not used. So I reduced its size to get it out of my way. prints…
A talon mag holder which fits standard picatinny rails! Best suited for side rails, specifically 5mm tall rails. Made for the Dart Zone Nexus Pro X. Easily slide or clip in and out talon mags, for quick reloads! Take advantage of new…
This is a DIY powerbank built from a Nexus 7 battery and a powerbank circuit from https://www.aliexpress.com/item/33046467419.html The board is held in place using hot glue, the battery using a strip of double sided tape. Top and bottom…
This spring spacer for the Nexus Pro makes 180+ fps possible, especially with barrel modifications.
The nexus pro is devoid of any sort of sling point and I am planning on using it as a secondary to my Aeon pro. While the Aeon pro is just as accurate (if not more during my testing) it isn't as consistent as the Nexus because it doesn't…
Simple spacer designed to fit in the Nexus Pro X and provide an extra 50mm of spring compression. NOTE: I don't recommend using this with the stock spring, which has very low frequency and will be more subject to settling. I recommend…
The Aeon Pro X is debatably the best budget pro blaster, it even has a mod pack by the manufacturer! But it turns out the mod pack is some spacers, or so it seems. I took off the stock attachment and checked out the spring one night, and…
theres a +20, +30, +40 fps spacer
Quick and simple wallmount for my old rusty Nexus 7 refurbished as Home Assistant dashboard.
.4 nozzle 4 Perimeters [walls] no supports
Introducing the Shrub Spacer, an adjustable spring spacer for the Nexus Pro X nerf blaster! This screw spacer allows for finer tuning of performance, adding between 18mm-28mm of precompression. The Screw portion features a square profile…
I believe this is the Myoho Muramasa from Scarlet Nexus. I used the cosplay guide for references. Should be full scaled. Base is 1 solid piece, The two other files are for those who want to slot in the blade. I am "pretty" sure itll fit…
Organize your gaming space in style! Introducing the NeXus Stand , a 3D-printed headset stand that blends modern design with functionality. Its robust and sleek structure provides a secure base for your headphones, keeping them within…
PTT retainer for attaching your Nexus or U-94/A PTT to any molle section. Must be printed in TPU or other sufficiently flexible filament. Simple, fast and easy to print. Two variations available to mount the PTT either horizontally or…
Seal Blowout Guard for Nexus Pro The Nexus Pro has an unusual telescoping gas tube in its breech system when modded for a tighter barrel seal and powerful spring, sometimes this telescoping piece will overextend (blowout) and leak air.…
I remixed haphazardlynamed's designs to allow them to be used with button head bolts and also added versions that use 25mm bolts (button head compatible too). I also cleaned up a few artifacts that were present in the original that would…
Remix of the Nexus Pro skinny pusher that adds extra length to remove a lot of the slack during priming. As a result, this pusher can no longer feed full length darts. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No…
Pump grip for the Nexus Pro X Nerf blaster! Re-uses the screws, pin, and roller from the stock grip! Extensively battle tested at the Ragnaroktoberfest 2024 competitive tournament!! I recommend printing with at least 5 walls and 10…
Simple Tablet stand for my Nexus 7 but will work with any tablet (even an iphone) I guess, wedge shaped so that it can be used to position the Tablet in different positions.... Category: Other
I made some more simple parts that will work on both the Nexus and Aeon Pro X. The Safety does have a thin bottom that can be glued to the shell. It can be printed with a brim, trimmed off and glued. Either way works. The spacers can push…
Nexus from Star Craft 2: Legacy of the Void. Disclaimer: This model is the intellectual property of Blizzard Entertainment, Inc. Reproduction for personal use is not explicitly prohibited under the Blizzard EULA but attempting to profit…
Allows unprimed reloading on your Nexus Pro!
Hello Everyone! This is my replacement grip for the Nexus Pro. It is a bit larger than the stock grip, both in width and the distance from the trigger. It uses the same screws as the stock grip, and can be swapped with the stock grip…
Dock designed for Xiaomi Mi A2 and stock USB-C cable but should fit others phones. Print on the side. No supports required. Once printed break the support on the hole for the cable adapter. Warning the STL for the cable should rest flat…
EXPERIMENTAL / WIP Remix of the skinny pusher. Eliminates slop, and the telescoping piece, to decrease areas of air leaks. ONLY WORKS WITH A MODIFIED BREECH
This is a remix of a remix of the 3-speed cover so it fits on my sparta amazone. I made the gap where the cable should go through wider so it fits the 7 speed shifter of my Sparta Amazone better
I made several variations of the original design by haphazardlynamed. Also, it requires an M5 nut and M5x16mm bolt (the original post says 10mm but that was too short). I've added versions that are Aeon Pro compatible Made for 17/32"…
Have a Stream Deck and an iCue Nexus with too little space on your desk? Look no further that the Stream Deck Nexus Dock! (Any USB Extension cable required for Nexus) Compatible with Stream Deck MK1
Hardware required and install instructions are same as the original
Attach with double-stick tape Print face down. Supports needed.
Really this is a way to add a better or longer barrel 16mm od to your nexus pro. in addition you can put silly nstrike attachments to it.
Safety Delete for the Nexus or Aeon Pro Replaces the safety lock, so you can disable the function but not have a hole in the side of the blaster prints without supports Category: Toy & Game Accessories
This turns the mag adapter on the Nexus Pro into a detent system allowing for mag swaps without needing to touch any levers. I kept hitting the Maxwell release instead lol ENJOY! :) INSTRUCTIONS: Print the parts in the orientation shown.…
Trigger Safety Delete mod for the Nexus Pro X. covers the hole in blaster after removing the original safety. Snap-in. (print 2, one for each side)
Spring Guides for the NeXus Pro X. If you take your blaster apart often for tuning, you'll find that the Small Springs for the magazine and catch like to ‘sproing’ very easily and get lost. these small guide parts help to retain the…
Print at 20% infill 0.15 layer hight Normal supports
The Adventure Force Nexus Pro X Spring Tuning Spacer Set uses a series of spacers to fine-tune the performance of the Nexus Pro X with the installed spring. This set includes three full-size spacers and one half-spacer to add…
Matches this male portion: https://elementrimming.com/products/itw-nexus-16mm-5-8-pom-helmet-side-release-buckle-a9hsb-1 Works for Giro Tremor helmets (and others) Printed in PETG with supports
This is an adapter to use a SCAR for 16mm barrels on your Adventure Force Nexus Pro. I used it to add a Tenacious Twist ( https://www.thingiverse.com/thing:3906599 ) to mine. Still trying to figure out if I like the tight or loose fit…
Locks out the adjustable stock on the Nexus Pro One annoyance I had with the Nexus Pro adjustable stock, is that you it can slip if pulled (like when picking up the blaster from the stock) (pushing on it when shouldering is fine tho) This…
Prints the same way as the original back facing up with touching build plate supports. I'm sure with a little bit of time, the original creator will get the sizing straightened up and make this superfluous.
This is a DDU/Dashboard Mount for a Nexus 6P. It will likely not fit anything else, that's why I added also the Fusion file for you to adapt it to other measurements. If you think about using a phone as a Simhub Dashboard, consider the…
This is a simple replacement for the new Adventure Force Nexus Pro X designed by Dart Zone. The front cap of the Nexus Pro is held in by two screws on each side. Remove the screws and then the front cap. Replace the front cap with this…
use with stock spring 15%infill with no supports Please download, like, and/or share
This is a cable protector for the USB-C cable that comes with the Nexus 5X. Print wit 100% infill, no supports, It's intentionally a very tight fit, I recommend inserting the cable immediately when the printer finishes when the plastic is…
If you’d like to get this model or explore even more of our work, including full figurine collections, exclusive designs, commercial licenses, and other great perks, you can find everything on our Patreon—see you there:…
I completely redesigned the supports to make the tube hold the load and not the zip straps. This project is a two-piece tubular holder for a cane or umbrella. It is fastened to the side of a NEXUS 4-wheel walker/rollator. The tube has…
Replacement magazine release lever for the Nexus Pro short magazine adapter I didn't like the original curved lever since it kinda snags my thumb when pulling the magazine, made this straight one for smoother operation UPDATE: added short…
The original model did not have enough overlap where it widened to the N-strike attachment portion. This resulted in the print snapping very easily at that point. I have thickened the design slightly at that point. It still works just…
This barrel grip replaces the stock orange muzzle and will allow for extended barrels to be installed in your Nexus Pro X. Cosmetically, I wanted this barrel mount to be less “chunky” that the stock muzzle or other “collet” style barrel…
This is a Nexus 7 tablet 2012 wall mount holder for installing Home Assistant dashboard. Back plate piece permanently attaches to wall via screw(s), while the top base piece is possible easy remove and attach again. A 90 degree charging…
Replacement shifter rubber grip. Compatible with Revoshift Nexus 7, not sure if others. For best results, print from a flexible filament. I've had great results with Fiberflex 40D, I think Flexifill 98A would do too. Print with the wider…
This is the missing lower piece to a 70m Nexus fan mod for the OG Xbox. It goes at the bottom and fills in the 2 holes, then the other mount holds the fan over it. The 70mm Nexus fan mod is here:…
Nexus Bowtie 3D Printable bowtie, with a connector for 20mm straps/bands. There are 2 versions, a flat version ideal for a flat top finish, looks great with ironing on top surfaces, and a version with inclinated faces to highlight the FDM…
This mount has room for two pins, that will charge the nexus when you put it in the mount. You will need: An usb cable A small peace of conductive metal, like a nail or similar. Preferably cobber. Iron will do. Sodering equipment Wire…
A simple Nexus 7 (2013) mount that you can fix with 2 M3x8 bolts and t-nuts. I use it to have a display for my Octoprint server with the Touch UI plugin. The mounting holes are on the right side with 1cm distance so it mounts flush to a…
this is a Nexus Pro grip (remixed from EnderSavesTheDay's tacticool nexus grip V3) inspired by FoamPro Shops hex grip. Print Settings Rafts: No Supports: No Resolution: 200 Infill: 20 Filament: PolyMaker PLA Category: Toy & Game Accessories
If you are like me and end up tossing the stock spring cap for your Nexus Pro or Max Stryker this will get you approximately stock FPS. It is a guesstimate as I don't have the exact measurements of the original.
A simple piece to launch a Nerf Elite Missile from the barrel of your Nexus Pro! Shoots about 6 Meters (20 or so ft) level. There is a full size (50mm) and an shorter (35mm) launcher. The 35mm one is pictured and tested by me. The longer…
These Adventure Force Nexus Pro + Max Stryker FPS Tuning Caps + Spring Spacers allow you to increase and decrease FPS on various springs by changing the pre-compression of the installed spring. Ratings are based on actual chronograph…
This is a somewhat print-optimized rifle grenade-style Mega XL launcher. I've tested this in the Max Dictator, but it should work in all Dart Zone Pro/Max and Adventure Force Pro blasters. The area that fits into the hole in the front of…
This spacer in conjunction with a stock Nexus Pro spring yeilds 150ish FPS. You can use your slicer to trim a little of the spacer off to lower the fps.
The Adventure Force Nexus Pro is among the most incredible blasters to hit the hobby! This Adventure Force Nexus Pro Top Rail Extension solves the unique rail design, making for one sleek, continuous Picatinny rail. We think the galaxy…
Wanted to create a slim wall mount for tablets which can be screwed into a lightswitch / junction box in place of a normal plate. Created to maximize the space on my smaller printer (FlashForge Adventurer 3) by printing on the side, at a…
3d printable model of a game avatar (nexus engineer) from game Madness: project nexus Supports - required
Barrel adapter for the Dart Zone (Adventure Force) Nexus Pro allows the mounting of a longer protruding barrel tube (16mm) aluminum barrel hardware needed: 5mm x 10mm bolt, head diameter less than 9mm 5mm nut with 8mm wrench flats…
Precise fit and easy to use unlike the roll bag/case the screwdrivers come with
Introducing the Stratos 200 Antenna Mounts by WrightFpv. Instagram This is a clean, durable, and lightweight antenna mounting solution designed specifically for the XLPower Stratos 200 helicopter, compatible with both the RadioMaster…
Replaces stock barrel coupler and muzzle. Merges the SCAR barrel by Eccentriclulz with the Birdcage Flash Hider (Model 08) by Becker Thorne. Reduces issues caused by friction-fit scars and creates a cleaner look. Install by removing stock…
A little mini lamp for your desk, nightstand, or as a fun side table piece. Wanted to try my hand at a tiny little lamp. This is compatible with Lamp Kit 001 and tea lights! The Assembly is easy. Choose what colors you want to print each…
Summary Hello everybody! Here is my latest project, a DIY HEAD UNIT for my Seat Leon mk1 (2004). It fits perfectly a NEXUS 7 and it is stuck on place using a double sided sticking tape. You can easily print this in two pieces or one as…
Simple cosmetic remix of this Nexus Pro X swappable barrel collet: Nexus Pro X Barrel Collet Frontend by RedCowl | Download free STL model | Printables.com Features the square design while also having a faux gas-block!
Placchette copri fori Gilera Nexus 300 / 500 - Aprilia SR Max 300 - Malaguti Madison 300 Stampa in PETG, ABS o PLA+ No supporti
Add some pizazz to you npx
In case you've broken your NPX catch, like I did, this is a replacement for it. I've run mine through at least a thousand shots(printed in PETG with 5 or more walls at 100% infill), and it has yet to break. When you open your NPX to…
Attachable on Aeon or Nexus pro, has port venting
This adapter press fits into the stock NPX muzzle to allow you to add any aftermarket 16mm __CAR you want without needed a longer barrel.
Open source FPS reducing tuning cap for the nexus pro blaster. Not extensively FPS tested at this time but should drop your velocity by 20-30 FPS. Print with supports. To install unscrew the stock cap and twist off. Remove the spring and…
This bottle opener was created to open a special lid on a bottle used with the IonTorrent S5 Genexus system used in genetic sequencing laboratories. It was printed with a Prusa MK3S+ using a 0.4mm brass nozzle. The model was made from…
Shimano nexus dynamo plug. It is male part of plug that is normally part of dynamo. 2 versions provided
Coaster/Plaque using the Nexus 6 logo.
