Counting matching models…
Heavy Duty Guitar or Bass Guitar Wall mount hidden Screw Design. Fix the bracket to wall then slot mount over Comes in - 53mm(approx internal prongs) - 53mm neck slot with 5mm wall offset - 53mm neck slot with with 10mm wall offset - 43mm…
Parametric VESA Offset By Qwerm A simple offset 100mm VESA mount. Included is a SolidWorks file that can easily be modified to create custom offsets. I have also included various sizes in 5mm increments from 15 to 85mm offsets. It is…
Dough / Clay roller with various offset plates wich can be easily printed and exchanged. I have printed it, so I could create a clay slab at a certain thickness. I have used it and it works very well. For the print you need 1x the roll…
There are 3 hooks for use in a Skadis pegboard. Each has its mounting point offset by 5mm to allow two hooks to be used to support 2 uneven ends of a single tool. See the picture of the hammer for an example. This is designed to support…
Quad snaps with different offsets to fit all multiboard installations.
I didn't want to buy compass or print something more complex than I needed. These circles are in 1 inch increments from 1-9 inches. The seam allowance circles are ¼", ½", and ¾". Just place the circle size you need. Find the seam…
A 50.5mm x 50.5mm input square for shaky Lack Legs with a disc (10cm diameter) whose surface area probably helps with stability. Mostly, I used this quick thing to boost up a leg that wasn't given enough turns before permanently…
cold shoe with offset hole on them
Offsets for mounting Pegboard on a wall. Print instructions Category: Organization
FS2026-rewinder-nut with different offsets
Printed at 10% infill in PETG with all standard settings from Bambu Studio for Generic PETG and the BambuLab A1
Designed for the 2025 Festool Contest: Pimp Your Workbench. One of the most frustrating parts of woodworking in a small space is processing full 4x8' sheet goods. These sacrificial spacers give your Festool MTF table enhanced…
After I installed my screen door (and created holes in my doorpost) I found out the door rubbed ever so slightly onto my floor mat. I recreated the stationary hinge and added some height offset so the door could clear the mat. I also…
parametric model added too ig, just in case u want some special tolerances i found my vultures orings to be super tight so they did get an amazing seal but the prime was real stiff
Dm me for any questions or to request a part for me to make, thank you.
Introducing the Artillery Bed Automatic Level Sensor Adapter with 1 & 2mm offsets, and a parametric Fusion File for additional adjustments. This design is tailored for parametric use, allowing simple parameter changes to achieve the…
parametric model added too ig, just in case u want some special tolerances i found my vultures orings to be super tight so they did get an amazing seal but the prime was real stiff
Update [Feb 26]: I no longer add the nut above the thingi, because then the distance is depending on the tightness of that nut, which can be different between the two. I no just use an 20 mm bolt and either piece of plastic screwed in…
I designed these wheels to better replicate the factory wheels and offsets for my Tamiya 911 GT3 (992) RC car (affiliate link) . I recommend printing at 0.08mm layer height. PLA has been fine. Supports will be required for most of these.…
to be used to start mains with the clamp raiser (raises for 25mm) offsets to be used on crosses, to offset 50mm
These little plates allow you to free up table space by moving your rockets to the wall. It also reduces the chances of them getting damaged by moving them around or trying to use the desk space for other efforts simultaneously. Printed…
I designed these very simple offsets to make a cheap storage shelf I bought on Amazon compatible with filament spools. They raise the space between the shelves by 4cm. Will fit most spool sizes depending on where you put the rods in the…
I wanted to adjust the amount of space that the printhead backplate and the X-axis endstop had between them on my Ender-3 printers, so I designed these. Very short and low material print. There are versions for both the standard backplate…
![Ikea Lack Foot For Balance/Stability [2-4mm offsets - w/ or w/o disc]](https://media.printables.com/media/prints/241987/images/2184337_fae8be31-65f0-4f36-a89b-3fbe2961d662/large_display_enclosure_foot_3mm_241987.png)
