Counting matching models…
I love my P1000f pedals from Simagic for many reasons, but the original pedal plates are not one of them. I found them too slippery and small, and the curvature is not precisely “sporty”—at least for open-wheel racing. My take on the…
I had downloaded the long throttle plate for the P1000 pedals from this post here: https://makerworld.com/en/models/456344#profileId-364175 and I wanted to make a brake pedal that matched. I have the Simagic P500 pedals, and the mounting…
Half height pcie bracket for NVIDIA Quadro K1200 NVS510 P600 P620 P1000 T600 T1000
i have redesigned the spacers because the original ones don't fit perfectly. if you're unlucky, the spacer in the cover breaks the first time you operate it. On the cylinder side, the spacer does not fit into the aluminum ring. i have…
This brake modification increases the usable space in the brake piston by freeing up unused space in the original design. This allows up to 3 springs to be used at once, significantly increasing pedal travel. Also, longer spring and…
Full height pcie bracket for NVIDIA Quadro K1200 NVS510 P600 P620 P1000 T600 T1000
I made this Lens cap for my friend. Lens diameter 77mm. Fit to Nikon CoolPix P1000. I used multicolor print. I changed the filament during printing. This is first version. Maybe I'll improve it later when it loses this cap again. Very…
You can add haptic feedback to the Simagic P1000 Pedals using the official peripheral or you can DIY by using some relatively inexpensive components. You'll need: Nobsound USB Amp (about 45eur at the end 2023) two “resonance speakers”…
Hardcase fits for Nikon P1100 and P1000.
(Universal) 15mm Rail Mount fit (12&20mm) red dot sight scope Hot Shoe adapter UFO Hunters or Mother Nature Spy will Love This... ;-) Print Settings Rafts: No Supports: Doesn't Matter Category: Hobby
You can adjust the path of the pedal precisely by increasing the size in the slicer / height. The Top is rounded so it dont caught by the Spring. The Spring has an inner diameter of 14mm. Print should be around 20 min. Printer Settings:…
There are a few brackets already out there for installed Nvidia Quadro P1000 or P620 graphics cards in the Lenovo M920q but I found them to be weak. Most of them attempted to keep the look of stamped steel and thus were too thin. They…
This 3D-printable adapter is designed for the Maxwell MP1000 vacuum cleaner, allowing the use of hoses of different sizes. It supports outer diameters of 32 mm, 35 mm, 38 mm, 40 mm, and 50 mm, with corresponding inner diameters to ensure…
I wanted to build a programmable mechanical keyboard without an unfamiliar layout requiring me to re-learn how to type all over again. There are a few commercial options that almost fit the bill, but the only fully-programmable one isn't…
Print in place (no hardware needed) clip-on pole saw pole accessory clamps are designed for easier transport of an EGO POWER+ PS1000 pole saw and two accessory 3.3' Carbon Fiber Extension poles between trucks, storage, and job sites. The…
A external powerbank holder for any cage/camera! I created this because my Sony a6300 really bad battery life. With this i have a LOT more recording time, better temps and better top grip! Needed parts: Adata AP10000QCD power bank, is…
A simple link plate designed to align and secure multiple Panasonic AK-HRP1000 panels into a clean, unified desktop setup-without modifying your table or rack mounting. This bracket connects units using their existing mounting points,…
Print in place (no hardware needed) clip-on pole saw pole accessory clamps are designed for easier transport of an EGO POWER+ PS1000 pole saw and two accessory 3.3' Carbon Fiber Extension poles between trucks, storage, and job sites. The…
Printed in PLA with 0.2 mm layer height. Add a pause command at the beginning of the bridging layer and insert the key. The printer will print over the key, connecting the opposite sides of the sleeve, holding it in position. I'm using…
There are a few brackets already out there for installed Nvidia Quadro P1000 or P620 graphics cards in the Lenovo M920q but I found them to be weak. Most of them attempted to keep the look of stamped steel and thus were too thin. They…
SFX PSU Mount LIAN LI SP1000P, made to mount the PSU under my desk.
Inner hole dimensions are 47x28mm, length is not so important. Model consist of cube with smaller and larger hole that you can just “plug” the WP1000 and inner wall will keep it where it should be. Theoretically you can resize this to fit…
