328 models
Some time ago I built a radio with a microcontroller and an FM-IC. I used an ordinary single-turn potentiometer to tune the frequency, but this did not work as intended. It was really difficult to tune in a specific frequency since the…
Print approx. €0.10–€0.12 excl. taxPreliminary estimate for one variant
Knob for Potentiometer 3296 print with brim and disable detect thin layers.
Print approx. €0.08–€0.09 excl. taxPreliminary estimate for one variant
Knob for rotary encoder or potentiometer with 6mm shaft.
Print approx. €0.22–€0.27 excl. taxPreliminary estimate for PETGSource material: PET
One and two-color knobs with an inner diameter of 4 mm on the axis of the potentiometer. It is perfectly suited to a music mixer, for example the DELTA AVE type. The original buttons fall out, these are a bit tighter. Tightness can be…
Print approx. €0.18–€0.22 excl. taxPreliminary estimate for one variant
Print some cool 2-color knobs to replace the stock one. Will fit on pretty much any potentiometer dial Share your makes, let's see some color Print instructions Category: 3D Printer Parts Print Settings Printer Brand: Prusa Printer: i3…
Print approx. €1.36–€1.67 excl. taxPreliminary estimate for PETGSource material: PET
Please note this model has been designed for and tested with a 0.25 mm nozzle. It contains small, precise mechanical elements and text that greatly benefit from smaller diameter nozzle. While it should be possible to print it with a…
Print approx. €0.04–€0.05 excl. taxPreliminary estimate for one variant
Just a simple box to encase a potentiometer in and run a 5mm cable through. The lid is held in place by 4x M3x10mm screws ¹. The design is tailored for a layer height of 0.15mm. The holes for the screws are designed to be printed upside…
Print approx. €1.84–€2.25 excl. taxPreliminary estimate for one variant
I designed a large knob for a 6mm shaft potentiometer to have better control in adjusting our ventilation system. You need one 3mm square nut (5.5 x 5.5 mm) and a 3x12mm hex screw to tighten the knob to the shaft. I have included the…
Print approx. €0.72–€0.88 excl. taxPreliminary estimate for one variant
Simple and small textured knob for potentiometers with 2mm hexagonal axle. Supports needed and draft recommended. I recommend printing it with as high quality as possible (small layer height & nozzle).
Print approx. €0.41–€0.50 excl. taxPreliminary estimate for PETGSource material: PET
I wanted a better, cooler-looking knob for my printer's LCD so I fiddled around in OpenSCAD and came up with this awesome design ! OMG I love it! It took me like 10 minutes and yet... Wow! I can't believe how well this worked out on the…
Print approx. €0.74–€0.91 excl. taxPreliminary estimate for one variant
Inspired by the cap of my 3D Connexion Space mouse, i decided to design a knob with the intention to mount it to a PWM dimmer. It should fit any potentiometer with a 6mm toothed shaft and be a pressfit. The knob is approx. 45mm in…
Print approx. €0.46–€0.56 excl. taxPreliminary estimate for PETGSource material: PET
Just a remix of the original model so it works as a knob for typical potentiometers and encoders. The internal diameter is 6mm, height is 8mm and a chamfer of 1mm on the backside is added for ease of assembly.
Print approx. €0.12–€0.14 excl. taxPreliminary estimate for one variant
Basic cover for electrically isolating the backs of Alpha potentiometers. Designed particularly for the RV16AF-10-15K-XXX-3LA with a diameter of 16.5mm, but might fit other models.
Print approx. €0.06–€0.08 excl. taxPreliminary estimate for PETGSource material: PET
Dieses präzise konzipierte Gehäuse für ein Schiebepotentiometer-Modul wurde entwickelt, um das Modul sicher zu halten und sauber in Ihr Elektronik- oder DIY-Projekt zu integrieren. Das Modul wird einfach mit Platinenschrauben in das…
Print approx. €3.18–€3.89 excl. taxPreliminary estimate for PETGSource material: PET
Print settings : 20% infill 3 walls
3D Model made for CAD. STEP/STP and STL provided. Model completely designed by me.
A Knob with knurled surface for Potentiometers with 6mm round axle. Slim 15mm diameter design. Prints well on an FDM printer with 0.1mm layer height. Ironing for the top surface is recommended. Print with shaft side downwards and colour…
Knobs to use on a potentiometer to make it easier to use and give it a better look
-Material: ~ 2gm -Printing time: ~ 0.2 hrs -Recommended quality: 0.2mm -Dimensions: 22 x 22 x 12 mm If you like my work, don't forget to buy me a coffe ☕ You can also follow me on my social networks: Linktree: https://linktr.ee/Alitaria
Basic knob for a potentiometer on a MIDI controller or any other device. Has an inset slot on the top that you can paint. Dimensions: Inner Diameter: 6.5mm Outer Diameter: 18.37mm Height: 20mm
D-Shaft Knob for Potentiometer/Rotary Encoder. Please remember to press Like if you download.
Hello! I made a simple potentiometer knob which I used to my project of audio mixer. Knobs are designed for 6mm potentiometer (hole is 6,2mm) it is sitting tight. ______________________________________ Cześć! Zrobiłem proste pokrętła…
Fader para potenciometro deslizante Category: Music
This knob fits a 6mm potentiometer with a slotted actuator. Why yet another design? This design uses grip fins and a rib to prevent slipping and has a nice press fit that is tolerant to variations in print quality. I also include Step and…
This is a remix of the fader knob that I met here, since the original model was not suitable for mass printing, I had to simplify it a little for better adhesion to the 3D printer table and the absence of the need to print with supports.…
This is a simple potentiometer knob for diy electronics. It has a little line to indicate the value.
Just a potentiometer model, nothing more created few years ago using solidworks 2019 .step file included .sldprt file included (solidworks 2019 or newer required / can be opened with fusion 360 as well)
Potentiometer knob made for 6mm shafts. The ID on the model is 6.15mm to account for printing error.
Potentiometer knobs with a nice grippy texture. There are four internal sizes to fit most potentiometers : standard 6mm diameter standard 6mm diameter with a deeper hole to cover the fixing nut larger 6.35mm diameter (often used on…
The usual situation … the maker's solution … Weekend, shops are closed, ordering takes too long …. This time I needed a knob for a potentiometer in a front panel. Compartment for knobs didn't contain any 4mm axis knobs … so let's make it.…
The large sibling of my Potentiometer Knob with knurled surface for Potentiometers with 6mm round axle. The hollow 20mm diameter design covers the nut completely. Prints well on an FDM printer with 0.2mm layer height. Print with shaft…
I designed these to work with my home made LM386 portable guitar amplifier. They are designed for a round (with rough edge) potentiometer with a 6mm shaft size. You may need to scale up or down slightly to get a tight fit. This one is…
I never seem to have the right potentiometer knob for the job on-hand. I could keep a reserve of interesting knobs on hand, but that takes space. Instead, I custom design the knobs, as needed. Here is another of my 3D knob print designs…
A clone of the knobs Boss used on their vintage rack units, i.e. the RV-1000. I bought a non-functional RV-1000 to repair and noticed it was missing 3 of the knobs. This is an almost 1:1 replica, the top cap even fits in the same way.…
Perilla de potenciómetro: Nombre del archivo STL: "PerillaPot.stl" Esta perilla de potenciómetro ha sido diseñada para mejorar la precisión y facilidad de uso de tus dispositivos electrónicos. Su diseño ergonómico proporciona un agarre…
I remodeled Cohencos knob to fit potentiometers with a 6mm inner diameter. I really like the rugged skin - it turns out very nice printed at 0.12 layer height.
My late Mom's old Panasonic table radio needed its volume control (with integrated power switch) replaced. The replacement parts would apparently be considered vintage now, but Philmore sells an appropriate value pot with an integrated…
I made this for the SP 404 MKii (and that's the only device I tested this with) but I think it should fit most pots. Instructions This model is composed of two parts, “knob” and “indicator” (red and white respectively in the picture…
Oct 25 2025 I adjusted the design to allow for more room to add the threaded inserts, and I added a 3mm hole to make it less messy to add the M2 inserts. Here is the OnShape layout. I have created a variable table so you can really…
Skull knob, 6mm ID for splined potentiometer. 0.20mm layer height, 0.40mm nozzle Brim No Supports In my experience, thermal coefficient of expansion varies between filament types. This is a tight fit that works well for silks. If you…
Pressure fit potentiometer knob for a potentiometer with a 6mm shaft Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2 Infill: 20% Filament: 3d Jake PLA Notes: Depending on the bedadhesion you…
A different take on the compound planetary gearbox. This time, we use split sun gears, synchronize the ring and planet gears. One sun gear will be fixed to the threaded shaft of the potentiometer (or some kind of tuning capacitor), the…
Just a clamp I designed for two potentiometer I need to put inside a control box. The clamp snaps on Potentiometer so it is not really necessary to put a nut on it for fixing. I used my Top Hat Rail / Cap Rail mount base plate to glue the…
Designed to fit perfectly on a shaft with 15mm length. There are two versions; with and without a small indicator.
Ok, this is my version of one more potentiometer knob. I made it on FreeCAD, the file is available for download, feel free to customize as you need.
Knurled potentiometer knob measuring 21mm tall and 22mm diameter. Fits a standard potentiometer keyed 6mm shaft.
This is a replacemet knob for the Synths: Yamaha AN1X Yamaha CS1X Yamaha CS2X No extra Hardware is used.
I needed to mount the potentiometer that came with a power supply rigidly. The back of the potentiometer says “Cosmos Tokyo RV24YN 20S B502 127C 3 2 1”. It came with this Genmitsu air cooled 300W spindle:…
Couldnt find anything to quickly mount a poti on a wooden board for prototyping. This is for potis with a outer thread diameter of 7mm. This is a 5min design and not rounded / polished / optimized or anything. Feel free to…
I made my own model of the potentiometer knob for the mixing console, it is great for restoration, the two models presented differ only in the tightness of the fit in the seat Category: Music
These are potentiometer knobs originally designed for Korg Synthesizers (Minilogue, Monologue...) but will fit on any other standard potentiometer. There are 2 designs to choose from: design 1 resembles the original knobs design 2 is a…
Knob for encoders and potentiometers with D-shaft 6mm Fusion model included
These knobs make it is easier to turn the potentiometer with your fingers, and it makes it obvious that these are to be turned to adjust something. Without the knob, you may be using your fingertips and accidentally pushing out other…
I needed some simple knobs and no time to get to an electronics store, so here is my 3D print design. The knob is designed to fit a 6mm potentiometer shaft. The knob has a 12mm base and has a height of 13mm, not including the indicator…
This is v1 of my pot box, this is to use a mechanical throttle cable with a potentiometer for electronic conversion of go karts, bike and totrods ect. I printed mine in black ABS but other materials would be suitable. this uses a 270…
WORKS ON REPLACEMENT SHORT SHAFT POTIENTIOMETERS Example: My 1980's OPTONICA TURNTABLE RP-4705 Optonica was Sharp's high-end audio brand and its attempt to make inroads into the audiophile market. This vintage direct drive turntable had a…
The knobs on my oven broke so I designed three different knob designs. Printed the chunky one in Blank eSun PETG.
I reverse engineered the stl files from DraftYeti's knob in OnShape so I could make some changes. The knob is more or less the same on the outside, with some minor tweaks, fillets and chamfers, that sort of thing. I noticed the original,…
Modified the LCD cover so you can fit one to three switches there to control lights, a raspberry or something else. I used the following switches and potentiometers:…
This is a part designed to fit snugly on 24 spline (fine splined) potentiometer (CTS, commonly used in electric guitars, unsure of what other, if any brands use this format.) There are any number of replacement and customized knobs but…
Its not perfect but it works ;) 8 Slider Version here: https://www.thingiverse.com/thing:4514085 UPDATE: I added Fader Knobs that look better than the stock ones This enclosure holds 5 slide potentiometers and one arduino nano. In my case…
Voici 2 versions de bouton pour potentiomètre 3296 avec un diamètre de la tige du potentiomètre de 4mm une version avec une gorge de 7mm et une version sans gorge Here are 2 versions of knob for 3296 potentiometer with a potentiometer…
A large potentiometer knob styled off a TC Electronic guitar pedal. This is suitable for a 6.35mm round shaft but could be scaled to fit other diameters, the overall diameter of the knob is 23.7mm. Category: DIY
2+ perimeters and 0.2mm layer height recommended, but should function with just about any settings. No supports needed. Should be a reasonably tight push fit over pots with toothed shafts.
I never seem to have the right potentiometer knob for the job on-hand. I could keep a reserve of interesting knobs in my parts bin, but that takes space. Instead, I custom design the knobs, as needed. Here is another of my 3D knob print…
Drehknöpfe für Einbaupotentiometer an Platten oder Gehäusen. Montage per Gewindestift M3 x 5mm
Print Tips Material: PLA Layerheight: 0.15mm (STRUCTURAL) Perimeters: 2 Infill: Grid Support: No
A highly customizable set of caps for any potentiometers in use on DJ equipment. Specifically designed for the D pots commonly found in mixing gear. The customization options allow for a simple switch to round pots. The design comes in…
customizable flat top knob, 6mm ID for splined potentiometer. 0.20mm layer height, 0.40mm nozzle Brim No Supports please give credit for remix, I'm interested to see what you creative folks come up with In my experience, thermal…
A replacement 4mm shaft for a potentiometer (Variable Resistor) that had broken in some old electronic equipment, this item has a shaft length of around 12mm, also uploaded is a longer 25mm length version. Even printing at high quality it…
Mount and shaft extender for rotary switch, now with PCB for LEDs. Base printed in Black PLA. Light Pipe Upper and Shaft Extender in transparent PETG. All printed with 100% infill for strength. Base and Upper are glued together and then…
Compound planetary gears with 11:1 ratio to achieve 10 full turns from a standard (almost) single turn potentiometer. Shown with 18mm guitar pot. The cap is glued on, either to outer ring or to the central gear for a slowly rotating dial.…
The first and the last 3mm 100% infill. Or just use the .3mf file.
Just a potentiometer knob, inner diameter is 6mm. Two versions, one with a round inner, the other with a D-shape inner.
Customized version of http://www.thingiverse.com/thing:1072393 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=1072393 Instructions Using the following options: Axis_Lenght = 7 Knob_Diameter = 20…
A Knob with colored Inserts, so that you can simply get different indexers on the Knob, and different encoder shaft sizings. Mine are for a 6mm encoder for a Hercules RMX Inspired by…
It is a simple potentiometer know with 6mm hole
A simple potentiometer knob I needed to fit a in a small space. Print without supports, with the hole facing down.
Knob for a keyed 6mm diameter potentiometer (trim pot). Keying includes a notch on one side and the slot typically used by a screwdriver. Snug fit and fine details. I printed at 0.12 mm layer height and with a brim to help with bed…
M7 nut for the common WH148 potentiometers that are everywhere. Intended to be printed as is with a 0.4 nozzle, no scaling required on a MK4. The model already includes a bit of clearance for a good fit. To make your own use an M7 hole in…
For potentiometer with 6mm axle. Mask included so you can mark buttons easy. Horizontal expansion applyed during designe for snug fit.
Dust Cover for Alpha 16mm potentiometer, was tired of ordering theses parts. Print Settings Printer Brand: Prusa Printer: i3 MK2.5 Rafts: No Supports: No Resolution: 0.2 Infill: 15% Filament: PETG PETG Category: Electronics
Knob for slide potentiometer 1x4mm tang used on DJ and audio mixers. Picture is of the ones on my controller and have my logo embossed into them, but the model included does not (keeps them universal for every one to use). Enjoy!
Simple potentiometer knob variants. Nothing too complex, just functional.
String Uses 8 of the 10 available turns of the potentiometer Printed on Prusa i3 MK3 in Black PLA with no support material For any modifications, here's a link to make a copy of my 3D geometry in Onshape If this helped you out, tips are…
With M2 nut for both versions and M3 for the bigger one
The knob model is very similar to the original and fits perfectly onto its shaft. I also made the knurls to rotate it better. You can print even without using supports
Just another stock-standard potentiometer knob, designed to fit the aesthetic of my electric violin Print Settings Printer: TEVO Tarantula Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.1 mm Infill: 15-30% Notes: Supports…
A Knob with knurled surface for potentiometer with standard 6.3mm round shaft and D-shaft. Slim 16mm diameter design. Prints well on an FDM printer with 0.1mm layer height. Ironing for the top surface is recommended. Print with shaft side…
Slim knob for a 6mm diameter shaft potentiometer. Two examples of fitting potentiometers are shown on the pictures.
Potentiometer knob for a knurled (press fit) knob with a 6mm ID and 42mm OD.
🚀 Support My Work🚀 If you enjoy my designs, you can help me keep the creative spark alive: Post a Make: Seeing your prints is the best reward! It also helps me earn Prusameters to keep the filament flowing. 💎 Like & Download: Your…
A replacement slider for DJ turntables like numark and pioneer
Ce volant permet de remplacer le bouton d'un potentiomètre en lui donnant un aspect SteamPunk. Print Settings Printer Brand: Creality Printer: CR10S PRO Supports: Yes Category: Decor
Smiley Face logo knob, 6mm ID for splined potentiometer. 0.20mm layer height, 0.40mm nozzle Brim No Supports In my experience, thermal coefficient of expansion varies between filament types. This is a tight fit that works well for silks.…
A knob for ɸ6mm potentiometers inspired by the 1982 Aston Martin Lagonda steering wheel (see photo), which has a strong vibe of 80s SciFi machines. Due to its special design, the knob is longer than normal. There are two lengths to choose…
and associated text is in no way sponsored by or affiliated with any company, organization, or real-world good that it may purport to portray. Speedo track Gear Box with Potentiometer Rownak Rayhan March 21st, 2023 The Speedo track Gear…
Dimmensions: 30x4mm height 4 or 6 mm Layer: 0.2 Infill: 20%
