Counting matching models…
RC102 and mobile phone holder. Necessary material: Selfie stick from Aliexpress - Ulanzi MT-58 120CM Mobile phone holder - any suitable Threaded rivet M5 - 2 pcs Screw with collar head M5 - 2 pcs Threaded reduction tripod thread 1/4" to…
Upgrade selfie stick v2 for Radiacode102/101. This spacer-joint allows a smooth change of the RC102 mount. https://www.printables.com/cs/model/552255-radiacode-102101-selfie-stick-v2 Installation: if I already have version 2 printed and…
This is a very robust and practical selfie stick holder for the Radiacode 10x radiation detector / gamma spectrometer. For easier storage and transportation the detector can be folded against the stick to make the package as small as…
Having recently acquired a Radiacode RC102 portable radiation detector it became necessary to fabricate some fixtures and accessories. This kit is comprised of: a shell to hold the Radiacode sensor which is wrapped in 4.8mm of shielding a…
I've printed it with PLA, 20% infill. PETG would probably be better, but have not tested it. Sized to allow Radiacode 110 with silicone cover. Have not tested it without the cover. This is a pretty rough and basic model, and not an exact…
Depending on just how much of a nuke-nerd you are, you might want to bust out your copy of Knoll, turn to page 122, and measure certain parameters of your PSRD. This model can hold credit-card sources in a couple of orientations with…
Modified Version of https://www.thingiverse.com/thing:6639714 (Made by Scanner73) Additional Bumper. Fits an Radiacode 10x MUST BE PRINTED WITH TPU, OTHERWISE YOU CANT PUT THE RADIACODE IN I've used Bambulab TPU for AMS (68D) Printer:…
Designed and build this car window mount/belt holder for Radiacode103 radiation counter/detector. You can mount this to your car window (max window thickness 5mm) or simply hang it of your belt, backpack loop. There is a bit of play when…
Print it using 30% or more , can print without support also You can optionaly also seal it with candle wax later.
This 1-liter Marinelli cup achieves the maximum possible efficiency through its optimized geometry, perfect for low-level measurements. The seal must be printed from TPE. To make it completely watertight, you may want to coat it with some…
My take on the RadiaCode selfie stick holder. Folds flat to the stick, to reduce the footprint in your backpack. It's a tight fit to avoid shaking off your device. I printed it standing upright, to have layers perpendicular to the flex of…
I've had trouble arranging samples in my lead castle so that the sensor is close but not making contact. This simple jig allows you to place small samples in a well under the device - and should make arranging things inside the castle…
A semi rugged case for the Scintillator spectrometer by RadiaCode. Use TPU as the seal PETG for the case PCTG for the window* *my best results for translucency were using the following settings: 0 top layers 0 bottom layers infill:…
You will need: A window cut to size! M3 bolts! Use TPU for the seal. Use PETG/PCTG for the Clip and Case. If you use PolyCarbonate remember to scale the model in the slicer to compensate for shrinkage ( Not PCCF )
This stand allows a Radiacode 110 Gamma Spectrometer w/Silicone Case to be held in place with the detector facing upwards so that the official Marinelli Beaker from Radiacode can be placed on with the seal upwards to facilitate liquid…
Rugged case meant for the Radiacode 110 with silicone case . I'm not sure what to use the lid size for yet, two versions are included, open and closed. Hinges 6 M3*30mm Remix The model was made with OnShape and should be available to all…
This 1-liter Marinelli cup achieves the maximum possible efficiency through its optimized geometry, perfect for low-level measurements. The seal must be printed from TPE. To make it completely watertight, you may want to coat it with some…
