Counting matching models…
Rlaarlo Gladiator ROG1 Dumbo RC X10F(G) Receiver Tray Adapter. This is a reworked tray to house the X10F(G) receiver that allows the larger receiver to fin inside the stock chassis. I used PLA at 100% for the stiffness since this part…
Unser Sky Q Receiver ist immer so heiß geworden habe mir solche Standfüße konstruiert. Habe eines mit 50 mm höhe oder 30mm gemacht.
Tanq-S conversion to analog with cradle for an ELRS receiver module with enough space to route cables and antenna.
I printed it with 0.16 mm Layer height. No supports needed. You may need to add a brim to prevent the pieces from falling over.
I really like that you can see if the mic is connected and muted or not on the USB receiver, but the blinking when not connected is very annoying. This simple sleeve can be pushed over to cover it and pulled up to view it again.…
Based on this model: https://www.printables.com/model/280117-radiolynx-holders Designed to accept a 3/8"-16 to ¼"-20 threaded insert. Then you can attach any sort of clamp that works with ¼"-20 studs. I'm personally using a “magic arm”…
Hardware Needed: (1) 1/4x28 Bolt - 1.5" or longer (1) 1/4x28 Nut
Hitch Receiver for 6mm x 6mm square feature. Hole pattern attaches directly to the 3ronco scale RC car by Casadio.
A stand for the easysmx x20 controller and its receiver. Basically like the original . I just added a cutout in the back of the stand to safely store the receiver of the controller, when not in use. I printed mine on a CoreOne. The sides…
I had to make smaller for the duboRc reciever.
This will make the inside of the box bigger so that way there is more room, will also allow for the ability to flip the receiver 180 incase you have wires that are too short to reach like my case with the steering servo
A hitch receiver plug with Rialta branding. A Winnebago Rialta is a small Class C motorhome that Winnebago built mainly from the mid-1990s through about 2005 . The Rialta was built using a Volkswagen Eurovan chassis and is a classic…
Falcon SRx2 v4 Receiver Board – 3D Reference Model (STL) This is a 3D mechanical reference model of the Falcon SRx2 v4 receiver board , intended for enclosure design, mounting layout, and fit verification . The model focuses on external…
Falcon SRx1-PSU Receiver Board – 3D Reference Model (STL) This is a 3D mechanical reference model of the Falcon SRx1-PSU receiver board , intended for enclosure design, mounting layout, and fit verification . The model focuses on external…
These adapters will allow you to screw a Max8 esc with no modifications to the top of the receiver box. If fitting a long motor such as the Hobbywing 4278 to an Arrma Kraton 4s, there is limited space to fit a Max8 esc in front of the…
This antenna mast support bracket is designed for mounting telescoping fiberglass antenna masts to a standard vehicle 2" adjustable drop hitch receiver . The adjustable drop hitch pictured is from Harbor Freight, although this will likely…
Enclosure for FPV receiver. 20×20 mounting. Protects the receiver from dirt, impacts, and other physical damage.
Wall mount for Tuya Zigbee Garage Door Receiver, https://www.aliexpress.com/item/1005005622553564.html . Should be a press fit for easy insertion and removal. Wiring: Connect one wire to NC (normally closed) and the other wire to NO…
"waterproof" box for the spektrum sr315 receiver. The wires should fold over the top and flat down the front of the case. The Cover will pinch all of the wires. Add a bead of sealant below and above the wires where they fold over the box…
Trailer hitch cover fits 2026 Honda Passport or similar with OEM trailer hitch and 2" receiver. Recommended Print Settings: Material: PETG or ABS recommended for outdoor use (PLA okay for short-term use) Infill: 20–40% for strength Layer…
I designed a stand for the Telekom 5G receiver to use it without the wall mount. Print Settings Printer Brand: Prusa Printer: MK4S MMU3 Rafts: No Supports: Yes Resolution: 0.2 Infill: 20%
For single Avatar VTX Antenna and RC Reciever such as ELRS module with antenna. mounts at the rear, slides over pillars
I designed this alternative case for the "1Mii B06Ultra" Bluetooth 5.3 audio receiver based on the original case, but with antennas moved to the opposite side. This way, the antennas can point upwards, while audio and power cables are…
Without the riser, the cage's cold shoe mount blocks the DJI receiver's aux cable output. With the riser, there's plenty of room for the aux cable to clear the cold shoe.
This is a case for the DrokBT Bluetooth audio receiver module the following features: Antenna through hole Hole in the lid for LED light (put a clean-cut 11 mm transparent piece of filament into this hole to act as a light channel) Hidden…
A compatible replacement in case you lose the original blanks that your wireless Shure rackmount hardware comes with. I print these out of PETG, but flex filament may also work well. Print in the orientation provided (flat side down) with…
I image a lot of machines, then ship them out. This clip allows me to attach a keyring to the USB so I never again forget to remove it.
I need a way to mount a Hollyland receiver to a wall. I found this model that I used for mounting an NPF Hollyland Transmitter to a stand, and modified it to allow for mounting it to the wall with screws.
Relocation for receiver box off of servo onto angled center brace rails
This is an adaption of SadSnifits 3D shell for the WavePhoenix receiver remixed to fit the E104 module.
It's a simple no-frills stand for the Malahit DSP2. Receiver fits perfectly, and all controls and buttons are easily accessible. The radio on its own makes its own controls akward to access unless you're holding it on one hand. This stand…
Project Overview: 2S LiPo High-Current Power Box with two Sbus inputs This circuit is a high-performance power distribution system designed for large-scale RC models. It manages power from dual batteries to drive up to 16 High-Voltage…
I use 4 M3x8mm bolts for the Falcan Smart Receiver and 5 #6 1/2 screws for the CG1500. The mount can be placed either left, right or centrally at the bottom of the CG1500, you could install 2 of them in the left and right positions if you…
I built a bunch of modular audio gear boxes for rackmount equipment. I designed these feet and "feet receivers" to be installed on the boxes so they would stack securely. You'll find the files for the feet, receivers for the top of your…
MJX Hyper Go 14209 receiver box print with TPU, supports from build plate only
Fits the common “RTL2832U ADS-B” ADB receivers found on various sites that come with a metal enclosure (e.g. https://de.aliexpress.com/item/1005005466363998.html)
I made this to mount an actual watertight receiver box in the boat since Proboat couldn't be bothered. This keeps the receiver from going haywire if/when it gets wet. Mounts using the factory screws to the boat, and then the Traxxas 3628…
This is a remix of a parabolic reflector in which I modified the receiver holder mount to accept an ultrasonic ~16 mm diameter receiver. Used Cyanoacrylate glue (Krazy Glue) to glue the 2 halves and hot-glue to secure the receiver to the…
I hated the look of the lightspeed receiver and the cable on my desk, so I decided to make something useful that gave me the option to charge the mouse with the cable when I needed it. The receiver fits on the print and the cable fits…
Two part design to make it a bit easier to print without support. The lip needs to be glued in place. The holder is meant to be stuck to any flat surface and will hold your remote. Very simple :)
Volume knob for Yamaha rx-v340rds receiver. No supports or raft is needed. 16-minute print.
This mount allows you to mount this TaoTronics Bluetooth 5.0 Transmitter/Receiver Bluetooth device (model number TT-BA08) with the magic of magnets. I don't know if this will actually be of any use to anyone as the device appears to be…
Befestigung um den sky Q Receiver an der Rückseite der Fernseher an den VESA200 Verschraubungen anzubringen. Eine Version ist horizontal, die andere vertikal. Die Öffnungen und Schlitze lassen die Betriebshitze sehr gut abstrahlen. Die…
This device allows you to send audio from your PC, mobile phone... to an amplifier, sound system, headphones... in a comfortable and simple way, therefore we don't need an annoying wire. I have designed this custom case to be able to…
Simple TPU ring retainer for SpaceMouse receiver. Keeps mouse and receiver together and fits nicely in 3DConnexion carry case. Print Settings: Material: TPU Layer height: 0.2mm (could go coarser if desired) Wall loops: 2 Infill: 15%…
Receiver Mount Futaba R304SBE for RC Car Category: R/C Vehicles
Three parts, Box, lit and seal. The seal glue it in the lit and use a small piece of foam on the front/top of the box. Use TPU for the seal
Weather station case for an esp32 D1 mini and a RF receiver. Project repository for the hardware: https://gitlab.com/raupulus/esp32-weatherstation-bresser-read-868mhz-cc1101
A simple desktop stand for the Dexcom CGM Receiver that may be weighted. It is a smooth fit for me without gripping the receiver. The menu buttons remain usable while in the holder. I like having mine on my desk at work, but did not like…
This is a simple holder for the FRSKY D8R Plus Receiver. It can be mounted anywhere in the model to establish a secure position for the receiver. You can mount it with four small screws or just glue it in place.
A light weight holder for a small vtx or rx (receiver) or anything that you might need to add to your build.
Rlaarlo Gladiator ROG1 Dumbo RC X10F(G) Receiver Tray Adapter. This is a reworked tray to house the X10F(G) receiver that allows the larger receiver to fin inside the stock chassis. I used PLA at 100% for the stiffness since this part…
Replacement for lost knob. Print instructions Category: Audio Print Settings Printer Brand: Prusa Printer: Prusa Mk2 Supports: No Resolution: 0.15x0.4mm Infill: Octagone Filament: esun PETG black Post-Printing A tad white color to see it…
The goal was to keep the original placement of the receiver box and provides an addition 10mm clearance for the larger 4274 motor. BOM m3x20 2 m3x30 2 5x3mm foam m3 inserts 6 Print Support: Yes Material: PLA
This custom 3D-printed tray is designed to house the Radiomaster DBR4 receiver in the dead center of the Rekon 10 Pro frame , positioned just below the 30x30 flight stack. The tray fits securely in the battery strap section, maintaining…
This is a custom bearing extractor and bearing receiver for 8 of the 12 bearings used in a Norco Fluid rear suspension. The other 4 bearings will require you punch them out or use a sliding hammer bearing puller sadly. Additionally, the…
Simple housing for a KY-022 Infrared Receiver Module The hole for the actual receiver is 9x9mm This was modeled off a module measuring 15.4 x 24.18 x 15.69mm. (This includes the pins and receiver) Print Settings Printer Brand: Creality…
Mini Receiver Unit! A replacement receiver piece for Flygonial's Protean blaster, including a new cage for mini-sized flywheels (pulsar/hurricane). Assembly and wiring is the same as the original Protean, and you will need a mag release…
If you don't have a printer, I do sell them(velcro included) on my site for cheap with free shipping for those in the USA. https://shop.ke9bos.com/ This is something I made for my ham radio adventures. This has been really helpful for me…
This is a bigger version of the original receiver box top part for a MJX Hyper Go 14210, 14209 or H14BM (only tested with 14210). It has the "max" size, that's fits, without modify the shell mounting height etc..
Xbox pc wireless gaming receiver smaller case. It has a USB plug included so you don't have to untangle it every time.
I have modified the rugged box to be able to fit 4x LD Systems MEI1000G2 receivers as well as 4x AA batteries, there is a small 5th slot which you can use the metal clip at the back of each receiver to clip onto the dividing walls so they…
OpenSourceEV Parts designs, produces, and shares 3D‑printed parts for Rivian EVs. Staying true to our open‑source mission, every product we create comes with free STL files so anyone can remix, customize, or print at home for little to no…
a mount for receiver and battery also a mag mount for the frame I'm using the furitek unity
The USB receiver for the Logitech G535 is small, easy to lose and non-replaceable. I created this adapter as a travel companion for the headset to keep the USB receiver safe by mounting it to the inside of the headset when not in use. The…
scx24 meus battery tray i used a unity brushless motor
The most common complaint that I got with the Manticore project is that the receivers are just too big for most printers. I've split them up into smaller parts to make it more doable for most people. You will need ten 1.5 inch 8x32 screws…
This is intended so that the pin can be kept safely stored with the hitch, and this cover could press into place with the TPU round nubbins popping into place on the hitch receiver's pin holes. If you use the 3mf… I probably chose the…
A simple and lightweight holder/mount for small radio receiver. Designed to suspend the receiver and keeping it from touching other conducting parts of the drone (You should still use proper heat shrink and insulation though). Print with…
2024-12 UPGRADE Improved design, the lid closes more tightly. It depends on which PLA manufacturer you print with, sometimes the lid opens normally and with another manufacturer it is very difficult. Filament - standard settings, 0.2
Unser Sky Q Receiver ist immer so heiß geworden habe mir solche Standfüße konstruiert. Habe eines mit 50 mm höhe oder 30mm gemacht.
Spacer for a double UK socket (2 gang) to hold your Aqara G4 doorbell receiver / chime with pegs to wrap the wires round too.
FrSky Tandem TDMX dual-band receiver Case (new version, not soldering required)
This is a peg grasper / peg receiver for ninja warrior training. IMPORTANT. When creating ninja holds with 3D printing, the printables have natural weaknesses which run between each printing plane (i.e., the layers themselves can separate…
Tanq-S conversion to analog with cradle for an ELRS receiver module with enough space to route cables and antenna.
This is to mount a Milwaukee Packout Magnetic Bin to a Multiboard using MultiConnect. Get the connectors here: https://www.printables.com/model/716558-multiconnect-generic-connector-for-multiboard
Protective case for the receiver "ATS25 max decoder" with a stylus slot.
Stronger if printed on its side with supports. Gcode file is 50% infill. Files include with and without antenna tube mount.
Like the title says this plate moves the ESC / receiver box forward to make room for the installation of the 540XL motor.
I'm not a fan of gluing the electronic components in the rc car. During maintenance or replacement, removal is very tedious and may no longer look nice. To get around this problem, I designed a holder for my current setup that can hold…
QLS plate for mounting anywhere. 3 Screw holes are provided. Remixed for even less supports and material! Printed flat on bed w organic tree supports Made and tested with PLA - .3/.6 - 2 Walls -4 Top/Bottom -
To assembly you will need two M2.5x5mm socket head screws and two M3 threaded inserts NOTE: The Receiver Box Lid will require support material.
Simple replacement for original. Mountinghole not as deep countersunk for added strengh since its printed in such orientation.
Wall mount for ParemTech PTLevel Home Receiver. Attached using 2 3M Command Strips. I designed the height to cover the status LEDs. I consider it a nuisance light :) Please Rate and share your Make! :)
Needed a higher feet for the ONKYO 746 receiver for a better air flow. This has fixed the overheating issue within the cabinet.
Case for RF Adapter, using Xbox 360 Slim RF Board. Sources: https://github.com/ginokgx/xbox360slimRF https://github.com/wiredopposite/OGX-Mini
Print at 100% infill so it wont crack under some vise tension (1) ¼-20 x 1.5" Bolt is the only hardware needed
A mount for an FrSky ArcherRS receiver with antenna guides designed to fit on my SoXoS 550 RC Heli. I soldered the leads to the ArcherRS and wanted to have it mounted nicely and the antennas guided, nothing too fancy but maybe useful for…
Simple mount for ELRS Receiver with the "Flat" antenna. Sized to fit a 25mm x 25mm stack. Sized to fit the BetaFPV Lite Receiver with the Flat Antenna (Roughly 12mm x 12mm). The small box is built in support that is designed to be…
This is a receiver shelf for the Freewing T-33 Shooting Star. It is designed to go under the cockpit / hatch between the EDF inlets, behind the Blue Box and above where the wing connectors enter. Placement is not too far off CG and if…
Print in an upright position for increased groove stability. Check out my other fischertechnik compatible parts .
I recently had to go on insulin and had to move to a CGM. The receiver is so small I needed a better way to keep track of it. So here we are. Model prints with no supports. Model has some tight clearances. Printed on SV06 plus .3mm…
