55 models
Accurate CAD files of the Rekon7 drone frame parts created from measurements and reference scans. Not 100% perfect, but close. You can use these files to create your own parts to fit on the frame. Files provided in .f3d/.f3z format for…
These TPU landing feet are custom-designed to mount under each motor on the Rekon 10 Pro frame, providing durable skids for smoother landings and protecting the frame during takeoff and landing. Each foot/skid has 4 mounting holes to…
This custom 3D-printed tray is designed to house the Radiomaster DBR4 receiver in the dead center of the Rekon 10 Pro frame , positioned just below the 30x30 flight stack. The tray fits securely in the battery strap section, maintaining…
Remixed the mount for a smaller GPS Category: 3D Printing
This TPU front-end camera mount for the Rekon 10 Pro frame allows you to mount an O3 or O4 camera far enough forward, thereby removing propellers from view. It also provides an integrated finger mount, allowing you to attach an action…
The original 3D printed part that came with the rekon 5 did not fit my Vifly Finder 2. So I made my own based on the design of the original. Can be printed without supports in TPU. You might need longer mounting screws. Print Settings…
RX mount to place diveristy behind fpv cam Category: 3D Printing
This custom 3D-printed tray is designed to house the Radiomaster DBR4 receiver in the dead center of the Rekon 10 Pro frame , positioned just below the 30x30 flight stack. The tray fits securely in the battery strap section, maintaining…
This custom 3D-printed mount is designed for the Rekon 10 Pro FPV drone frame , offering a secure and optimized placement for iFlight Albatross V2 antennas and the Matek M10Q-5883 GNSS module . Perfect for enhancing signal performance and…
This custom TPU mount is designed for a vertical T-style antenna and attaches directly to a standoff on your FPV drone. While it was designed specifically for the Rekon 10 Pro frame, it may also work with other FPV drones that use similar…
I didn't like the quality of the printed parts of the Rekon35 frame I got a few weeks ago. Still have to build it, but first made the parts I needed. Nicer GPS mount Caddx peanut mount The frame/battery mounts are done with spacers…
Mount for a Matek Systems 3901-L0X Optical Flow and Lidar Rangefinder sensor to fit flush on the bottom of the Rekon 7 drone frame. The mount requires 2x M3x4 and 4x M2x8 fixings to assemble. Route the wires up through one of the holes in…
Remixed so it can be used with the original screws. Attached a crude STEP file, so you can modify it further if needed. Tried it out and worked very well now :)
Please check @MagicAerials_514389's upload for best printing instructions: https://www.printables.com/model/1225007-rekon-10-pro-o3-and-action-camera-mount It's a tight fit for the O4 camera so make sure to clean up any excess filament…
Simple Mount from the original design to 14x14x15mm runCam Nano Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Doesn't Matter Supports: Yes Resolution: 200 infill: 20 Filament: SainSmart TPU Black Category: R/C Vehicles
15 degree angle camera mount for O4 Air Unit Pro for the Rekon 5. Antenna mount for the TrueRC Singularity antenna w/tube.
Unfortunately, the standard camera of the Walksnail Avatar digital FPV system does not fit in the HGLRC Rekon7 frame. In order to be able to install the system anyway, I designed other mounting plates and an adapter for the VTX. I have…
Rekon35 is a cool concept, but I had issues with the battery tray not maintaining contact and the model would reboot mid flight. remix flattens out the battery tray to allow use of the original 2s battery holder as intended and adds…
meant to be paired with https://www.printables.com/model/218336-runcam-thumb-model-fpv-mount this model replaces the mount that attaches to the quad. Custom resized. Mounting bracket to hold a runcam thumb action camera.
The GPS mount that came with the rekon 5 did not fit my GPS. So I designed my own for the Baitian BN-180T. It seems to hold quite well but in case you want it to be more secure you could add some double sided tape or wrap it with a zip…
Rekon 7 HD pro Buzzer and XT60 mounts for that https://youtu.be/TbkZb6YF4V8
This rear mount and GPS mount needed as a for Walksnail digital conversion for the 18650 Rekon35 analogue version, the mount include a type C connector location for the Walksnail VTX for updating the firmware and downloading the footage…
Runcam Thumb Camera mount for Rekon35 - this is designed as to push the capacitor up into the mount, to allow mounting the Walksnail Pro Camera. THis is to reuse the front standoff and to use 2mm self tapper screws as the rear of the mount
This is a small collection of mounts for the #NanoLongRange DIY drone project. The mounts include: Insta360 Go (version 1) Beitian BN-180 GPS module Combined Insta360 Go and Beitian BN-180 GPS module You can view my flight video using a…
arm guards vor HGLRC Rekon LR4 Frame
The Immortal T placement is not optimal if it's the only antenna you have on the quad, I use it because I use a diversity receiver with 2 antennas. This mount works well if you have U.FL to SMA adapters to attach your antennas for the air…
*anti screw slipping and detachable (designed for use with srew inserts) rekon35 runcam thumb pro mount. For rekon35 quadcopter. Visit me on thingiverse: https://www.thingiverse.com/thing:58426 *i am the original maker
These are custom TPU mounts for my specific build of the Rekon 4 LR Frame Kit . They were designed to mount the components I used but I figured I'd post this in case anyone was building a similar configuration and found these useful. I…
Every time I put my drone in a backpack, I was afraid of damage. I didn't want to draw and then print a big box for transport, so I created this simple frame that will prevent damage mainly to the props and arms. You need to remove the…
Single and double antenna mount for the HGLRC Rekon 5. Should/could fit other frames with 4mm standoffs that are 12mm apart (center to center). Made it to fit a single antenna (DJI O3) as well as the double antennas of the DJI O4. Printed…
Simple cooling for the Rekon35 drone. A simple model that uses relatively little filament. Cooling is provided by a classic 60mm fan, which you will definitely have somewhere in your workshop :) For quick connection, the model also…
Common cover for cameras on your Rekon35 drone - So: Caddx Ratel 2 and Runcam Thumb Pro. (I carry the drone on a backpack, and it's not good when the direct sun shines on the camera lenses, plus protection against damage will come in…
1.verze hradu
The Immortal T placement is not optimal if it's the only antenna you have on the quad, I use it because I use a diversity receiver with 2 antennas. This mount works well if you have U.FL to SMA adapters to attach your antennas for the air…
New GPS GOKU GM10 v3 mount. The mount is slightly extended, so the GPS is further away from the VTX antenna. Even such a little thing helped quite a bit in finding satellites. Completely plug and play Print with TPU
Common cover for cameras on your Rekon35 drone - So: Caddx Ratel 2 and Runcam Thumb Pro. (I carry the drone on a backpack, and it's not good when the direct sun shines on the camera lenses, plus protection against damage will come in…
Single and double antenna mount for the HGLRC Rekon 5. Should/could fit other frames with 4mm standoffs that are 12mm apart (center to center). Made it to fit a single antenna (DJI O3) as well as the double antennas of the DJI O4. Printed…
Same as original except that I turned the DXF file into a 2mm and 3mm STL file. Category: R/C Vehicles
Trying a few different styles to see how weight/stiffness is. Category: R/C Vehicles
This custom 3D-printed bottom plate is designed specifically for the Rekon 10 Pro frame. It fits below the bottom-most carbon fiber plate, providing a smooth and flat surface for securely bottom-mounting large batteries like the iFlight…
These are full size GoPro mounting blades crudely pasted onto a Rekon 4 base for mounting a camera onto the quadcopter. Category: R/C Vehicles
I had issues with the original 18650 battery tray after a couple of weeks, and decided to build my batteries into packs, and use xt30s instead of the spring tension mount that the quad was delivered with. This is just tall enough to keep…
This is a soft mount for a GPS (HGLRC M100). This get's the module far enough away from the motor EMF that the compass can be used for navigation. Included are the GPS holder, rx mounts for a crossfire nano rx antenna, and some soft…
- Simple stand for Rekon 35 drone. - Just print these two parts and use regular 2.5mm wire (CYKY) as a leg. You can set your own height and shape of the stand. - Recommend changing the filament in the text height layer :) or for owners of…
New GPS GOKU GM10 v3 mount. The mount is slightly extended, so the GPS is further away from the VTX antenna. Even such a little thing helped quite a bit in finding satellites. Completely plug and play Print with TPU
I made this to mount the large capacitor that comes with the Jijie (DakeFPV) H743 stack with 70amp ESC in the HGLRC Rekon 10 Pro frame. There isn't much space in the frame for the capacitor, so a discrete mount was the best solution using…
based on the original shape of the OEM part, I wanted to put an SMA antenna on my rekon35 quad.
the existing Gopro mount is a little too small to properly mount a gopro or other action camera.
For Rekon35 Walksnail conversion, this is a front mount as is to allow clearance for a Walksnail V2 VTX.
I was tired can't carry camera on this little drone so i designed 2S mod to give him more punch. Now i can do mid range fligth carrying insta go or go2. My bottom part is designed for the Mamba F411 25A AIO and the short version of the…
Fixed Mount for GoPro Mini 11 with TBS ND .. for more space für bigger lipospacks. 30 or 35° angle Category: 3D Printing
TPU parts for original Rekon 7 made to fit DJI O3 Air unit. Not exactly the cleanest job, but it fits fine and prints fine (GPS Mount requires support). Also the GPS module is 1 cm further away from drone body.
Unique features: -detachable thanks to brass srew inserts -no screw slipping since screw head gets blocked when screwed in → thight fit Visit me on thingiverse I am the original maker of this model…
A long rear GPS and SMA antenna mount for the Rekon 7 drone frame, to help promote RF separation and reduce the EM effects of your flight electronics. The GPS mount is sized for a 18x18 mm (180) sized GPS/compass module. The SMA connector…
![FPV Drone Landing Feet [19x19mm] (eg: for the Rekon 10 Pro)](https://media.printables.com/media/prints/1082369/images/8183131_8ecd968c-6b23-464b-bf70-d2fc79b6c8d3_73b21e60-60d6-45c5-a53f-c65c20a96fbe/photo2.jpg)
