Counting matching models…
Front loading desiccant boxes for AMS. These slide in and out without having to remove the filament to change out the desiccant and I also added a hole for an hygrometer. Hygrometer I used is 44mm in diameter…
Revolutionize Your Seed Cleaning Process Tired of spending hours tediously cleaning your harvested seeds? This 3D printable seed separator offers a quick and easy solution that saves time and money using ordinary house hold equipment - a…
back hurt? cant bend over? try the new shoe aid remover. really if you dont like stepping on the back of your shoe to get it off and dont like untying them this might be the solution for you. The dimensions of the model are too large to…
Micro SD Card Remover. Designed for the Gopro Hero 8, can also be used for other devices. The Gopro has such a thin slot for the Micro SD card that I can't remove it with my sausage fingers. Therefore, I have modified my potato chip…
Lost most of the supplied keys, made this design in order to be able to make more when needed. Print at 0.2 (or better) layer height, slowly since there are some very small indents on the sides that are needed to unlock the blocker.
PETG infill: 15 % layers: 0.2 mm perimeters: 3 recommendation: print with the handle up
This was design to fit the very tight space for removing the water heater drain plug on my motorhome.
Deutsch pin removing tools for size 16 and 20 pins. Print Settings. Strong Filament PA ASA ABS, PETG 0.12mm or fine layer height Seam position Random Print laying down, Stronger than printing up right, Supports needed.
Simple tool I designed to unscrew my LPG cap easier when refilling car.
Small handle for removing press fit inserts from a multiboard panel. Just thread it in and push up. It prints as downloaded without supports in under an hour (33 minutes on my Voron.)
This is a tool for removing/installing center blend door actuator in 2009-2014 Ford F150 (and others). In this application, the rear screw can't be accessed from the center console, due to a frame member which is directly above the…
This is a very basic wedge design with a 6.5mm gap to allow you to get under the knob and push the wedge forward to move the knob cap upward so it can be pulled off more easily for those who are not strong enough to manually pull the cap…
36mm tool for removing the thermostat from a Grohe rainshower system. The same process as in this video: However the video above uses the 34mm tool instead. The 36mm tool can be difficult to obtain so here is a version that can be printed…
Looked at the ticks dimensions on the wiki: The size of an adult tick ranges from 2.5 to 5.0 mm in a hungry state. A well-fed tick can reach 7-10 mm, some species are larger - 11 mm. I made my own version.
Light and small spade for removing ashes from the wood stove
Tool for removing joysticks from the Xbox Elite Series 2 controller . It makes maintenance and replacement quick and safe without damaging the controller
In the motorcycle I’m restoring, I need to remove 24mm shock absorber caps. The shock absorber looks as if it has never been disassembled, so after 27 years, a lot of force is required to unscrew them. At the same time, I wanted to ensure…
This tool helps to get a little more torque on the plug in the pool deck to remove it. I found it also works on the bottom of my salt shaker with a similar finger grip! Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: No…
Soporte para tener organizados tus ganchos. Holder to keep your hooks organized.
Das Removing Tool für DT Swiss P1800 ist speziell entwickelt, um das Entfernen der Nabe bei DT Swiss P1800 Laufrädern zu erleichtern. Bei Wartungs- oder Reparaturarbeiten ist es oft notwendig, die Nabe zu demontieren, um an die Speichen…
Do it without removing the faucet! This is the ring that covers the faucet's connection point to the wall. You can easily install it without removing your faucet. Standard settings. Water-resistant filament would be better. PLA also works.
This tool is used to remove the tubes from eSpring water filter system when servicing. It's supposed to be supplied by the manufacturer when you buy spare parts but I lost it so I made it myself.
I rotate and press the screw on the supports. When it gets some grip , I move around . When I hear a crack, I pull.
You still need 2 angle profiles 200 mm x 20 mm x 1 mm made of stainless steel. The thread in the cap may need to be recut. New may 2026: base for the top step Man braucht noch 2 Winkelprofile 200 mm x 20 mm x 1 mm aus Edelstahl. Das…
Cover plate - for covering belt winders without removing the belt Replacement for the one-piece old-school covers without removing the belt Dimensions from hole to hole approx. 100mm, printable without supports, with a smooth or textured…
An arm that uses the original fan and relocates it near the laser for removing burned leftovers. how to: 1. unscrew the fan 2.unscrew the back plate and detach the fan wire 3. put super glue on the borders of the fan CAUTION : you have to…
a tool for removing apples from a tree
Tool for removing the Bar End Insert from Triumph handlebars (28.6 / 22 mm). You only need an M6 bolt (minimum 40 mm long) and an M6 flange nut. If you print the tool from a more durable material, a washer will not be necessary. I printed…
A 3/8" Allen or internal hex finger driver for removing the jaw retaining bolts from Kurt style machining vises. MK2 version has a 1/4" square drive hole to add an extension to remove bolts from extra deep soft jaws. I printed mine out of…
This is a remixe of https://www.printables.com/model/1103052-pick-tool-for-dental-aligners. I made an eye for better grip. Printed with ASA, layer 0.2 and 60% infill.
Tool for removing the Bar End Insert from Triumph handlebars (28.6 / 22 mm). You only need an M6 bolt (minimum 40 mm long) and an M6 flange nut. If you print the tool from a more durable material, a washer will not be necessary. I printed…
it was made for the machine to work, the native part broke and I made a new one based on it.
I've developed a safety knife for removing duct tape and electrical tape from surfaces. This knife can be attached to a mop extension. I've attached a link to a replacement blade:…
If you are using a third party heating element on your AD5M that has a separate 4-pin connector on the wire, this tool will make installing and removing that connector easier. Print with PETG filament using a 0.4mm nozzle, 0.2mm layer…
EDIT: Please make sure that this is the wrench that fits you blender models. Other users posted variations that fit newer Vitamix blenders. This thing is a tool I used to replace blades on our Vitamix blender. It's a remix of another…
Model to fit some Seiko H357 models, it won't fit all as they reused the movement on a number of styles. Please note this is untested as I haven't used it yet. I printed at 100% infill.
Now available in multiple versions with different offset from the nomina dimension.
The nozzle on the Bosch Advanced Vac 20 vacuum cleaner for removing dirt from storage for small parts. When it is necessary to remove dirt from the storage areas of small parts such as screws and nuts, you can use this nozzle. It allows…
English version below J'ai créé mon propre outil de démontage de capot transparent de vanne Burkert 8691. Sa référence officielle est 674077 Si vous avez besoin de plus d'informations ou quoi que ce soit, n'hésitez pas a me contacter…
