Counting matching models…
I needed a mount for my scarlet 2i2 to declutter my desk, so I drew up this design, intended to mount wit 4 countersunk screws. The audio interface slides in and is held in place through a tight friction fit, sturdy enough to not move…
I found several existing mounts for the Focusrite Scarlett Solo (3rd Gen), but all of them had some fancy locking mechanism and/or required supports to print properly. More importantly, it looked like all of them were too close to the…
Remix of @Christoph_79778 's Scarlett 2i2 mount, widened to match the dimensions of the newer 4th Gen.
Does not require support material Print with back face (power cord plugin area) on the print bed
CHOOSE WHAT YOU LIKE: A single complete piece / two parts Choose if you want your Scarlett to be removable or not - also a few options on how removable Additional cable holders with various sizes Honeycomb may save print material I…
Under-desk mount for the Focusrite Scarlett Solo audio interface, mounts with either 3M double sided adhesive tape, or with screws up to 3.5mm in diameter. The mount consists of two pieces which are mirror images, both pieces print…
I printed it in PETG on a 0.6mm nozzle at 0.4mm layer height with supports for the fillet of the screw wing. It's very snug - it does not budge when pulling out an audio cable. Print it in the direction of the STL as the back has an inset…
Support à fixer sous un bureau ou un plan de travail pour la carte son Focusrite Scarlett 2i4 2nd Gen et 2i2 2nd Gen Je voulais un support qui me permette de sortir la carte de son logement en cas de besoin. Attention, les languettes sont…
A simple bracket to hold a 4i4 Audio Interface to the bottom of a desk. Has recessed 3mm holes for a variety of screws.
Under-table mount for Focusrite 2i4 2nd gen audio interface This is a remix of the 2i4 bracket by DJERO . The design has been modified to be printable on the side, and require no supports. Printing on the side should also make the tabs…
A vertical stand with a perfect fit for the Focusrite Scarlett Solo. Free some space on your desk !
I previously had a Scarlett 2i2 Gen 2 mounted under my desk with the mount from ziller88 . After the Interface died i bought a 2i2 Gen4 and modified the mount to work with the new interface. It comes in 4 Versions: Scarlett 2i2 Gen4 desk…
Under desk mount for the Focusrite Scarlett Solo 4th Gen. (note: 3rd gen and 4th gen are different sizes, 4th gen is bigger so this will not fit the 3rd gen) Designed to not require supports, to allow this it should be printed on one of…
This is an under desk bracket for the Scarlett Solo 3rd Gen. 4x #4 countersunk screws XLR cable clip is 6.5mm wide Print with support everywhere with back the side, where the cable clip is, down.
Je ne trouvais pas de supports pour les Focusrite Scarlett 2i2 3rd Gen donc j'en ai fait un car ce modèle est bien plus petit que ses prédécesseurs. Je me suis inspiré de ce support https://www.thingiverse.com/thing:3647280 pour faire…
Holder for mounting your Focusrite Scarlett Solo 3 under the Desk. The Solo 3 can be inserted after mounting the holders under the desk. Dimensions: Height: 45,5 mm Width: 24 mm Length: 57 mm Hole diameter: 3 mm Print instructions Layer…
The Focusrite Scarlett Solo/2i2 4th Generation seem to have no way to disable or dim their status LEDs. If the unit is in a bedroom and the computer is never shutdown, this presents a problem. This is just a basic cover to snap on when…
Designed an easy-to-print under-desk shelf mount for my Focusrite Scarlett Solo interface. I printed mine out of PLA and mounted it with 3M VHB tape. My particular desk has a 20mm square metal frame under the top shelf, so this hangs low…
This bracket has mounting holes compatible with the Balolo mounting grid, but of course you can also screw it to the underside of a desk. Easy to print, PLA is fine, no supports required.
https://www.hi3d.ai/share/photorealistic-bikini-woman-3d-collectible-figurine--4845b2a652a54d3495b242b124d28e08?inviteCode=Y8Axoeva9P&shareType=history_model
You can use this model to mount you FOCUSRITE SCARLETT 2I2 under the table. Category: Music
Focusrite Scarlett 2i2 - Vertical Stand.
A simple under desk mounting solution for the Focusrite Scarlett Solo (4th Gen) audio interface. I couldn't find any solutions that I liked for mounting, so I designed my own! This is also designed using Zoo's modeling app ! The included…
Designed a desk mount for my Focusrite Scarlett 6i6 audio interface. The idea was to move it below the desk, to reduce the number of cables running across my desk. This thing comes with 1 model (bracket) that needs to be printed 4 times,…
Design This model is for securing a Focusrite Scarlet 8i6 underneath a desk or to a wall. There are various alternative designs but I wanted one that stopped movement forwards and backwards and both sides connected across the bottom, so I…
This mounts a Focus Scarlett 2i2 audio interface (3rd generation) under a desk or table. It includes a large hook for headphones below. There is a smaller hook in back for extra loops of headphone cable. I modeled this in Fusion360. Along…
This is a edit of Ziller88's design. His file for 1st gen has the incorrect foot-groove size and would not work with 1st gen devices (Serial number's starting with S) If you don't know what generation your device is, see this link:…
the Scarlett Solo table attachment 3D print fits perfectly under any table, whether screwed or glued in my case(acrylic)
This is remixed from mirasderbissalin's desk mount to support a 1" desk and a 3rd Gen Focusrite Scarlet Solo. The desk fit is a little loose, has some space for a 3M command strip although it hasn't been needed. Print Settings Printer…
This is a Focusrite Scarlett 2i2 Mount for the Balolo setup cockpit
See “Differences” below for more information
Mount for Focusrite Scarlett 2i2
A under desk mount for a Scarlett Solo. Includes ports on the back for the USB c and the ¼in Ports.
Under desk mount for Scarlett 4i4. As drawn, it fits, albeit very snug. If you want a little wiggle room, might want to scale it up a bit. I used #8 flat top screws. (U.S.) The screws countersink perfectly to clear the housing of the…
Desktop Stand for the Focusrite Scarlett Solo 4th Gen
Gone with the Wind - Scarlett O'Hara (Vivien Leigh) - 1939 3D printable model.
My knobs became sticky as the plasitic started to break down. So I made a replacement for them. This is a replica Knob for Focusrite Scarlett 2i4 (First Gen). Might fit other Focusrite Hardware aswell. Feel free to leave a comment, if it…
There is no shortage of Images of Scarlett Johansson portraying Black Widow in Iron Man 2. Here are three I found and mad into Lithophane STL files. Again the are images were found on the web, Links provided. Black Widow-Scarlett…
Iconic Movie Moments - Gone with the Wind - Frankly Scarlett, I Don't Give A Damn - 1939 3D printable model.
The Focusrite Scarlett 2i2 4th Gen is a lovely USB audio interface with an iconic look! However, the red metallic chassis doesn't fit in with every aesthetic around it. In my case, I was building a digital piano setup, and the original…
Mounting Bracket for Scarlett solo 3rd gen with the microphone cable holder.
Remix of the original model to support the different size and foot/input locations on the Gen 4 Scarlett Solo
This is just a model I made for my own purposes, maybe you find a use for it. The mount I used previously was quite flexible, not secure, and everytime I plugged something in, it moved. So I drew up another one with focus on sturdiness…
This is a replica of the Scarlett Solo red metal casing. It can be printed in whatever color or material you like. Replacing the case: Removing the original red case is not hard at all, just peel back the two lower pads on the bottom,…
Focusrite Scarlett Solo 3rd Gen cover for those who hate red color=)
Pretty shelf for the 2i2! Two STL files available, one also has the top side indent that I use for my Minimixer, as seen in the picture. The other one has a smooth top. Edit: After a while I realized it's actually perfect for holding it…
Rack Ears for Focusrite Scarlett 18i20 4th Gen
Template to help with mounting Focusrite Scarlett 2i4 2nd Gen bracket
Friction fit 10 inch rack mount for Focusrite Scarlett 8i6
print two times on the flat side Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Filament: Prusament PETG Category: Audio
I made this to install it under my desk. 0.2mm tolerance on every side, works great. 3mm diameter countersink holes, I used 4mm screws
A simple, low-cost, easy-to-print, Scarlett 2i2 Gen 4 Under Desk Mount that uses 3M Command Large Picture Hanging Strips Print Settings Choose your preferred model: Raised or Flat. Use Raised if your table has a 20 mm thick metal bar like…
Made from pics I found & liked. Models not perfect. Made to 150mm, re-size as needed. All made in STL & 3MF formats.
La caja está diseñada para transportar la tarjeta de sonido Focusrite Scarlett 2i2, pero también es válida para la Scarlett solo, dentro cabe la tarjeta con su soporte y bolsa de tela. Está diseñada para poner la tarjeta en la parte…
Print Settings Rafts: No Supports: Yes Resolution: 0.2 Infill: 20% Filament material: PLA Notes: Printed horizontally with supports
I recommend printing this mount on its rear face, with the release tab facing upwards and some tree supports for the tab, as shown in the model photos. The mounting holes are sized for #6 screws.
No supports needed, printed in Pla with ender 3 printer.
A vertical stand I made for my gen 4 Scarlett 2i2! Made to be stable while visually unobtrusive. :) Doesn't cover the XLR or USB ports on the back regardless of its orientation. You can add rubber feet under the base if you want to get…
Remixed this Focusrite Scarlett 2i2 under desk mount so that it uses Multiconnect slots to mount instead of the screw holes. Printed with the same orientation as the original, and no supports needed. I printed this in PETG, which has…
Soporte para tarjeta de sonido Focusrite Scarlett 2i2
Top and bottom mount for Focusrite Scarlett Solo Gen 3.
Print settings Material: PLA Supports: organic/tree (refer to screenshot)
The push button of my Focusrite Scarlett 18i20 MKI broke of. Only replacement parts for MKII were available so I created an MKI version. Not extremely elegant, but it works. Possible enhancements in the future: little more rounded top and…
this design :https://www.thingiverse.com/thing:4870981 modified to my needs
I saw the thingyfab stand on thomann and I tried to remake it
Desktop stand - 30-degree tilted version for Focusrite Scarlett Solo 3rd Gen. Second, Smaller version: https://www.printables.com/model/1794623-focusrite-scarlett-solo-3rd-gen-hellraiser-v2 Cutouts: For 2 large jacks and thick cables For…
Simple veritcal mount for Focusrite Scarlet solo 4th gen. sound card.
There are slots for rubber strips on the bottom piece to prevent slipping.
Made from pics I found & liked. Models not perfect. Made to 150mm, re-size as needed. All made in STL & 3MF formats.
Scarlett is annoying. She's too precious for peg holes in her feet so she doesn't fit most Joe stands. Well take this!
printed in PLA It took ~13h to print holder + screws on MK4, used the tree supports with front side facing down
If you have the oddly specific combo of a 4i4 interface and O2 amp, use this to mount them under your desk. The mount has end stops in the back so that the units stay put when plugging stuff in, and don't slide around. It also has a few…
Two Objects in one file! You can split the object in your slicer to remove or move the support in it. So you can always use slicer supports for it. Uploaded a version without the support! This isnt as flimsy. Hope it serves you well...
I wanted to get my Scarlett Solo off of my desk to clear up some space. This ties into my monitor's VESA mounts and then holds it just below the bottom bezel. The model doesn't require any supports. It has a pin that was intended to keep…
A custom made rack to fit the Focusrite Scarlett 4i4 4th gen. In combination with a charger, a usbc hub and a ethernet dongle. This makes all the port accsessable on the backside as XLR chassis connectors. Requires som soldering. Tried to…
This 3D model was designed by me and created for practical use. -No supports -pla -I attached it wit Powerstrips
This angled stand is designed for the Focusrite Scarlett 16i16 USB audio interface. Improved visibility: Tilts the unit 15° for better viewing of input meters and front panel LEDs at desk height. Cable-friendly: Raises the interface…
Coupling and mating part for the Scarlett SL 1543 Blender
This is a 1U rack mount for a Focusrite ScarlettSolo 3rd Gen audio interface along with a fan controller found on Amazon. You will need to take the rubber feet off the bottom of the audio interface for it to fit.
A under desk mount for my old Focusrite Scarlett 2i2 and my new FiiO K13 R2R. I realize that pretty much no one will have this exact combo, but since one of my viewers asked for it, I figured I just might upload it. Especially for those…
A quick and dirty model that worked for me - I wanted a friction fit, so it is tight. Insert Focusrite at your own risk. Some more notes: Only for Focusrite Scarlet Solo Gen 4 - USBC You must remove the rubber feet before inserting the…
The Focusrite Scarlett 2i2 (4th gen) has a circular volume LED around the input 1 and 2 inputs. At the time of this file's creation, there is no software solution for disabling it. This knob was designed to block out that light. This knob…
May need to stick on some rubber feet, can slip around a bit while turning knobs/plugging unplugging leads
This is my take on Scarlett from G.I. Joe. You might need to adjust it to your desired size.
Two brackets that allow you to mount your Focusrite Scarlett 18i8 Audio Interface to the underside of your desk. The mounts are made for the 3rd generation but it should work just fine for the 1st and 2nd as well. Start by attaching the…
So I saw CalmLogic's version of this, which was a remix of mirasderbissalin's and decided I would copy it completely, and I am only giving credit for the idea and layout of it, I just eyeballed how it looked and changed all the…
A stand to slightly elevate the Focusrite Solo 3rd Gen from the deck, so the cable can be neatly routed underneath the interface. The gap at the rear is over 10mm tall, and can easily accept XLR cable. In this print setting, I try to use…
I needed a mount for my Focusrite Scarlet Solo 4th Gen to declutter my desk. The audio interface slides in and is held in place through a tight friction fit, sturdy enough to not move when inserting/removing an instrument cable, but loose…
I originally used two of my initial remix to hold the audio interface up. It eventually stretched out the brackets and fell out. The single, center hole design of the original bracket doesn't seem to do well with heavy and/or wide…
Simple feet that can be added to the Scarlett Solo First Gen to move it up from the table a bit. I use it to get the controls of my desk lamp below it, as you can see in the picture. You can probably use it for a ton of other stuff. With…
A vertical mount that holds the Scarlett Solo (Gen 3) and Cloudlifter CL-1 Mic Activator together in a vertical orientation. It has mounting holes and a drill guide for marking placement. A plate for the use of nano tape or alike incase…
This is a mount for a Scarlett Solo 4th Gen (audio interface). I probably made about 5 prototypes, but this one finally fit perfectly . It took about 3 hours and 30 minutes to print (Old version) using PLA+. Screws are needed, for mine I…
The Why Wanted to have my SS higher, since it is situated behind my monitor stand. Very stable, I used to have problems with my SS moving around my desk but that doesn't happen now. Allows for better cable management thanks to the 20mm…
Cake topper Layer height: 0.2 mm Infill: 15%
NOTE: completed a 3rd revision of this model that works with all 2i2 generations as it started to sag over time with PLA. Check my profile for the updated stand. Focusrite 2i2 (1st gen) monitor stand platform with cable hooks, reversible…
This holder is to neatly mount your Focusrite Scarlett 2i2 under the desk in a vertical orientation.
(I make this model with the feet removed in mind.) first model i do. i tried to make a clip to keep it from going back when you plug something in it but it kept breaking. i added some lines inside so it's pretty snugged and does not move…
Support to hold the focusrite scarlett solo 4gen sound interface under the monitor
![Scarlett 2i2 Studio [4Gen] under Desk mount](https://media.printables.com/media/prints/b68b4700-3848-405d-b901-74fde379532b/images/11786680_3c32e39d-e46f-4922-b98f-9b2ac1437c51_c89430e2-26eb-434b-b8f3-26d8c4719788/639045345285121010.png)
