115 models
My Wife's students, somehow, tend to lose the spools from her tape dispenser. I designed this replacement for her. Model is hollow and really only needs supports on the posts.
"A Simple 3D Printed Scotch Yoke Mechanism" is a model I designed for a mechanisms class. The motor used in this model is an N20 60RPM 6VDC gear motor powered by a 3VDC battery pack, thus the motor runs at approximately 30RPM. With the…
This is a tape dispenser for the Gridfinity modular storage system. It is compact at 1x2 squares, and features cutting teeth that split tape effortlessly. It is not possible to stack other blocks on top. This takes standard 2 inch tape…
A minimal tape dispenser/roller for Scotch tape (for rolls with an internal diameter of 25mm, external diameter up to 55mm). Uses a piace of blade cut from a cling-film (or other kitchenware) roll, cut to a length of 20mm. Can be used…
Keep your counter clean with this dish wand & sponge organizer. It will hold both round or rectangle sponges depending on which anti-slide pin you use. Excess water is drained back into the sink and not left on the counter. Easy to print,…
Needs to be printed diagonally on most printers. You can just barely squeeze it in on a Bambu without rotation, can print 4 at a time if you really wanted to. Designed to match the height of an ikea alex top drawer with the basic…
A stylish desktop tape dispenser for home or office use. This dispenser supports standard size Scotch tape roles with a core width of 1 inch (~26mm) and a tape width of 3/4 inch (~20 mm). * Features a double sawtooth design that catches…
This version helps tackle the problem with the wall popping out when you are pulling things from it. It is secured with a bolt in both places and will not budge no matter what you do.
After printing Singh Design's Tape Dispenser Automatic Tape Cutter model, I realised that I could not fit my desired 26mm (1") Scotch tape roll on the original roller. This new wheel and psuedo-bearing replace the original wheel, and can…
This is a tape dispenser centerpiece designed specifically for the 3M Scotch C-38 Tape Dispenser, but it should be fairly universally compatible. It has notches in 2/3 sides so that it can be more easily removed, but also reasonably…
Simple Gridfinity 3M Scotch tape holder. Printed on Bambu X1C using pro grey PLA filament as pictured.
The original tray for my wife's laminator broke after the cats knocked it off the nth time in a day so I decided to design a new one. I had a lot of issues with designing the tabs that it locks into. They work currently but if I feel like…
This is a model of the spool that holds the roll of tape in our tape dispenser. If yours is broken, this might be helpful! Fits 3M Scotch Tape rolls tightly. As with all functional parts, you should print this in the strongest plastic…
Made this Remix to attach a Honeycomb wall with strong 3M Scotch (or other double-sided tape with little to no lift of the wall (1mm) The particular tape I use by Scotch can hold up to 30kg (10cm tape per 1kg) I do not like command strips…
This is a remix of the 3M Tape Dispenser Core by rikkilambo on Thingiverse. His is a two piece make requiring supports. I combined the two parts in Tinkercad and then cut in half so supports aren't necessary. Just print two of these and…
Redesigned to fit the classic Scotch® Magic™ Tape 810 roll (3/4 in. x 36 yds, 19mm x 32.9 m). Specific size roll? Yes, but it's what I like to use and I hope others might find it handy. Print Settings Printer Homebrewed, Baby! Rafts…
Based on original, made for a quick n simple print … align “axis” directly upwards, add supports on build plate - did mine at 0.2mm in ASA but sure petg and pla would be fine. Carefully remove supports, clean ends if necessary and use. ……
6x1x6 gridfinity box that holds Scotch scissors. Includes magnet holes.
I've been meaning to design a tape holder as part of my quest to Gridfinitize my makerspace. So I came up with this simple and compact yet effective design. Its only 1 part, includes a tool for cutting tape, and you can easily hot swap…
cool scotch taper spool replacement
I ordered the wrong type of tape for the office and needed a dispenser... I added a second Base without the honeycomb holes. The axis is a M5 x 35mm bolt with a M5 lock nut. For the blade I used a broken blade from a cutter and superglued…
This is a remix of Tesa tape dispenser because I found that Scotch tape is slightly wider and not fit in holder. I just add negative object in Prusa slicer and created more space. You will find two 3mf files. First file is Tesa tape…
Sweet office companion or gift for a crafty person Excelent helper to wrap presents too!
This is a scotch tape dispenser designed to work with gridfinity. Features: Hollow body so you can add weight using sand or lead shot. Thread-in plugs seal in the loose material 3 Cutting blade options: Print the included file Trim a…
This is a redesigned Scotch Yoke mechanism. I had posted a non-printable sample design some time ago. Recently another Thingiverse user, Sprik, had generated a nice printable design. I made a couple and they worked very well, but the…
Update 2020-11-16: Created a better system for locking the arm clamps in place. I also added a wheel that would be considered a crappy blower fan. It has a lower profile and allows you to use an air compressor or canned air to spin the…
This remix only works with a scotch tape dispenser blade with 4 holes in the metal-- the outer two holes being 48mm apart. You will need 2 >5mm long M2 screws to retain the metal blade. You will need to cut some more plastic off the new…
A simple 1x5 Gridfinity bin that holds 38 mm to 42 mm scotch tape rools, like Tesafilm. Created to be as simple as possible, without a stacking lip and without magnet and screw holes. Print Instructions Any basic PLA should work 0.2 mm…
This the core that is inserted in the middle of the tape reel to hold it in place in the dispenser. For 26mm id reels, they are what I think is a standard for office dispensers. Our original reel is often lost, so now we all can print…
Remix of @brinkhoopla's design to fit a Scotch Brand H180 Tape Dispenser (aka tape gun). Used the Universal Hook blank from @mkingery to make it more user friendly. I believe this is best printed in PETG
This is a replacement for a roller that fits inside of a roll of Scotch tape in a dispenser. It is 34mm wide at the widest point and the roller that fits inside the tape is 24mm wide. Print on end with supports
This is remix on hook for tape for direct mount to the wall, no extra elements needed.
Stop endlessly searching for the end of your tape! Forget about picking the tape with your fingernail or cutting off a crumpled end. The solution is Tape Tab Buddy . Tape Tab Buddy is available in 2 sizes: Small Tape Tab Buddy (15 x 14…
Scotch Tape Dispenser Stiffener This part will transform a flimsy, unusable Scotch tape dispenser into a very usable piece. This part fits half inch tape. Pictures show dimensions of the dispenser that fits. The design is printed without…
Gridfinity organization system module for holding scotch tape refills (3 and 4 square length versions)
A 3D scan of a lint roller. This could be great if you use it for refills. Yes it does print! Just clip the base into the build plate for a smooth bottom surface.
Mario Cube 1 has to be printed with Suport under the Scotch nose. All other parts can be printed without support. To cut the Scotch use some cutter blade (9mm). Between Cube 1 and Cube 2 use 2 magnets to fix them together. Magnets should…
After printing Singh Design's Tape Dispenser Automatic Tape Cutter model, I realized the stock roller just wasn’t cutting it for the kind of tape rolls I actually use. The original part is sized for smaller rolls, but my setup demands…
Voici un support qui est simple à imprimer pour un rouleau de scotch. Il s'adapte aux plaques ikea Skadis.
I designed these things to filter cooling air on an assortment of devices I own. They feature Scotchbrite scouring pad filter media, snap on filter holder for easy maintenance, compact design, and tweaks for aero efficiency. Print the…
Scotch Tape Holder for the ikea Skadis. Uses my T Clip with locating pins model, so it only needs one clip seat to prevent rotation: https://www.printables.com/model/1213947-t-clip-with-locating-pins Works using low profile T Clips:…
I had a very specific tape dispenser. I could not find a fitted bin for it so I made this one from Seishin's OnShape Gridfinity Generator as a starting point. Scotch Tape Dispenser Model C-38. No magnets or screw holes. Link to OnShape if…
KTM Duke motorcycle scotch tape holder
This is a quick print of a Johnnie Walker Scotch logo. Set your printer to .2, then start with white, then red, black and gold. Hang it above the bar or in your man/woman cave! I have always enjoyed Liquor and Beer advertising since my…
Scotch Yoke Design from a die filer project I was working on Motor Bracket is sized for a 390 Motor, 28mm diameter 3x 4mm Threaded inserts used for the Yoke Support, and Bearing Bearing is sized for a 624zz (13mm Outer, 4mm Inner), Use…
Tired of a wet countertop? Print this to allow the dishwand to drain and dry over the sink.
I am an advertising collector for beer and liquor. My favorite scotch is Johnnie Walker Red. I could not find any signs that I could afford so I decided to make one. My make is ok, but it would have looked better with cream or parchment…
It's a clip for a standard scotch tape dispenser. Should fit generic as well. Snaps on easily and with a very satisfying noise. Print Settings Rafts: No Supports: Yes Resolution: 0.2mm Infill: 3 walls 30% gyroid Filament: Polymaker PLA…
Gridfinity Scotch Tape Holder A holder for storing your 3M Scotch Tape Dispenser. Fusion360 Fusion 360 file included for easier remixing. Check out my other designs for more Gridfinity. Category: Organization
If you have some scotch weld with the form factor 50mL (1.7 oz, 1:1 ratio - old version ), 37mL (1.25oz, 2:1 ratio old version ) or the current 43mL (1.43 oz, 2:3 ratio ), youll notice that nozzles are impossible to buy, and are like four…
All of the tape wheels I could find required supports, and many left the axel pegs printing in a very weak orientation. I thought that a folding design could solve these problems, and since it is placed inside the tape, the fold is held…
Wallmountable tape dispenser with cutter, countersunk screw holes for 6 #8 Screws of any length. 1 Piece print within 150x150x150mm standard printer 3d printer. No supports required
A ~12g, no support tape dispenser with sharp printed teeth and roll retention. No additional materials required.
Ersatzkern für Scotch Klebebandabroller. Innenachse muss separat gedruckt und nachträglich nur zusammengesteckt werden. Material: PETG
I needed one and decided to make one
Remixed (from scratch) for the Scotch Brite Dish Brush which has more of an overhang so it requires a bigger base. Print Settings Rafts: No Supports: No Notes: Print with threaded portion down. Post-Printing Don't forget to transfer the…
I don't know about you, but we love washing dishes using a dish wand. What we don't love is the amount of soap dispensed while using the wand. This is a little plug that reduces the size of the soap dispensing hole in the sponge…
Drew this up after seeing 507 Mechanical Movements #135 and thought it would be a great way to demonstrate what a reuleaux triangle is. You need to print 1 of everything except for the arm clamps which you need two of. This snaps/friction…
Edited the original to better fit my tape gun, also changed the way it attaches to the multiboard. No need for supports.
This is a ridiculously simple model. I used it when I was learning to model in the Onshape 3D editor. Source: https://cad.onshape.com/documents/be8ee93347bc30fb526870a3/w/2d7506cffdfd8429e25d6fb7/e/cd4f88f6b1b5f8c65b5918a5
The little tabs on the tape spool of our Scotch C17 tape dispenser broken when someone stepped on it. I designed this to replace the broken piece so we could again enjoy the great tape dispenser!
20-30% cubic infill 0.8mm walls, 2 wall lines Printed with PLA+ on an MP Mini Delta Supports touching buildplate 0.14mm layer height .blend included as source, .stl included for printing. Scotch Fastener: 3M ID CBGNAW011342 UPC…
porta scotch a forma di moto custom
We simply lost the original roll and needed a replacement. There were two other Models on printables but they did not match the required dimensions. We have a Scotch dispenser filled with sand and the sticky tape roll has an inner…
it's not the scotch dispenser itself, but it's just the holder part where you stick the tape in, i dont know if it works for your scotch dispenser tho Made with tinkercad only Stl. file 74kb
Core for a Scotch C-39 Double Wide Tape Dispenser. Print in three pieces. One Hub, Two Pins. Then depending on your tolerancing, press or glue the pins in. I have included the original solid works file, a Step export, and the STL files.
This is 34mm wide at the center tips, and 24mm wide for the part that holds the tape. The tips are 5mm in diameter. The major diameter is 25mm plus the ribs make it 26.5mm.
Printing may require some light internal supports. They can be a bit of a nuicance to remove, but it's ok. Fitting the tape dispenser into the reinforcement shell is also quite a tight fit and requires maneouvering the two parts inside of…
A fun little sign for Black And White Scotch. it will make a great sign for your bar or wall. A quick print. Prints at .2mm with white first, a color change to black at .6 and then finish with gold at 1 mm I have always enjoyed Liquor and…
This is a tape holder and dispenser. No need for nuts or glue to put it together. The whole thing can be assembled and disassembled by fitting the two parts together. Hope someone finds it useful. Enjoy!
Un petit dérouleur pour scotch en forme d'éléphant avec des dents pour couper le scotch. Remplissage de 20% à 30%, Comme je n'ai pas d'imprimante multi couleur, il faut l'imprimer puis le peindre. Il faut des supports pour les 2 pièces,…
Scotch Tape Gridfinity holder printed in PLA to hold my Scotch Tape holder in my drawer unit. Scotch Tape Gridfinity holder printed in PLA to hold my Scotch Tape holder in my drawer unit.
Meant to hold a Scotch Permanent Double-Sided Tape 12.7mm wide x 6.3m (34-8726-3661-7) https://www.amazon.ca/gp/product/B007Z7RFG8 Uses 6mm(dia) x 3mm(thickness) magnets in the case, 6mm(dia) x 1mm(thickness) magnets in the cap
A 1x2x3u Gridfinity bin for holding 2 standard Scotch Cristal tape rolls (although generic brands will probably work). There is also an alternative version for also holding thin (15mm wide) rulers within the same bin.
Remixed to make the bottom support stronger. We use the sponge holder and we push a brash between the 2 arms which works great but after a few months it snapped on they layer line. New design should prevent that.
Carriage for holding a scotchbrite pad for making repeatable lines, for creating a brushed aluminum surface finish I used this to create repeatable brushed finishes on milled aluminum, sanding to 400grit and then using maroon scotchbrite…
This is a slightly modified 2x2x0.5 bin from a multigrid collection that holds up to 3 standard packing tape rolls. As per multigrid recommendation: Layer height: 0.2 No supports 3 perimeters The licensing terms reflect the licensing of…
This holder is for tape with a paper that is more like a post it, label tape dispenser.For that kind of tape that you usually don't find. This was made by my dad to use it for packaging, for writing notes on boxes. Printed with 10%…
I have made this bottle neck lock sleeve when I bought a bottle of scotch with my brother, we stated that the only time we were going to drink from it would be when we are together. So, for fun, I made this lock sleeve, holding 2 lock,…
Easy to print foot for scotch brite dish brushes
The ones (currently) available are either too bulky or only have slots for two rolls of tape. Not only that, I noticed that the dimensions for the enclosure were slightly wider than the "standard" ones (we bought these in a pack of 24 at…
Adapt a Scotch lint roller refill to fit a “normal” lint roller, which takes refills that are 100mm in length and 38mm in diameter. I printed this lint roller handle:…
Missing your Scotch tape dispenser spool? Just print this. All you need are two m3x10 or shorter socket head cap screws.
Scotch Bottle Holds tape on the neck of the bottle Cap Uses a thread to screw onto the top of the bottle Encloses the tape so it can't fall off Bottle Stand Bottle Stand (with no teeth) Smaller version that doesn't have the teeth for…
Easy design and very practical if you have lost the scotch tape insert: Print: Material: PLA, CF-PLA Infill: 20-30% outer brim 3-5mm Have a good print All!!
Wall-mounted Scotch tape dispenser designed for easy one-handed use in workshops, offices, and maker spaces. It keeps the roll fixed on the wall so you can pull and tear tape with one hand while holding your workpiece with the other. The…
Scotch Tape An innovative design capable of holding your shot of scotch and your favorite adhesive. This is a pretty pun print, check out the short which contains detailed operation instructions. Im starting a new 3D printing youtube…
This build is yet another Mak-Cass based on the very popular optics sold by Surplus Shed from time to time: https://www.surpluss...tem/PL1298.html There are several excellent spins on this project, like this and this and this , and the…
Questo è un modello modificato rispetto a quello precedente. Realizzato in petg, layer 0,2. All'interno come si vede in figura ci sono 2 cuscinetti, scaricati da un modello in Printables ( si potevano usare anche in metallo) e modificando…
Drop in single piece Organiser to store Scissors, pens and labels.
Hard test for this tool because my best friend works in a shipping agency. V1 works very well but after 2 mounths it cracked then I remix it with with a reinforcement. Please write me for any changes or suggestions. Petg is a very top…
Printed with 0.2mm layer height, 20% gyroid infill, and (maybe unnecessary) tree supports. Specifically for “OfficeGoods Modern Acrylic Tape Dispenser” The 3mf file has Orca presets.
J'ai remixé un modele de support de scotch Skadis (que j'utilise dans mon atelier) en support pour Sopalin / Essuie tout pour qu'il puisse être fixé a ma crédence de cuisine a l'aide d'un simple morceau de double face. Quand ma cherie l'a…
Modified Springy Scotch Taper Spool to work in the @MiguelM Tape Dispenser
Prototype parts for Hop Scotch. Prints will require tree support to make tolerance. This is still in development and may not hold up to its own strength. Will update files and suggested materials as samples are printed and used. For one…
This is a plant tag for the Pepper of variety Scotch Bonnet in the font Billionaire Dreams
Remix of the Scotch Double Sided Tape Case created by Gigahawk. This case is for 3/4" double sided scotch tape in a disposable dispenser and uses 6x 6mm by 1.75mm magnets to hold it closed. I printed on a PRUSA CoreOne with 0.15mm…
Parts required: https://bodekier-blueprint-labs.base44.app/builds/69ceb587f041cbedccd211aa
A holder for a single scotch tape roll with dispenser for the Skadis pegboard system. 2 pieces: the main holder and a removable cap that keeps the tape on the holder while allowing you to replace the tape when it runs out. See the photos…
![Scotch Tape Dispenser Stiffener for 0.75 inch tape (Magic brand UK/EU product) [19 mm]](https://media.printables.com/media/prints/759128/images/5919321_02332be6-152e-4fbd-adf5-1160dfcc776b_16fc27b0-6883-435b-a695-fb3e6ac5c414/20240210_130423.jpg)
