Counting matching models…
Print flat sides down no supports. To use, plug into 12v 10amp power supply. Insert tool into coil and hold down the button until it glows, this usually takes a few seconds. Assembly instructions: Insert both the button and the power…
Remix of Myco Dogs model. I changed it up a bit to better suit what I wanted. Parts and affiliate links can be found on the original model. Print with both flat sides down with no supports. I used 15% infill with PLA+, but any filament…
This is for one of the extremely cheap (about $10 per) Induction Sterilizers that you can get from Amazon or other places. The 12V one isn't the fastest in the world, but should do “ok” on 18g needles and scalpels if you are trying to do…
I have a Fluval EVO 13.5 which is acting as a reef tank, and found that I would like to put in an in line UV filter to help with any type of bad bacteria within the tank. In this search I found the Auqa Shield UV Sterilizer Desktop…
Aqua UV 25w Classic shown in pictures. This mount makes it easy to affix your UV sterilizer in any orientation. Should fit most 2 inch UV sterilizers.
takes some 1-2 and 1-4 rods. split for printing. added a part that replaces the 3 end parts so that the nozzle can screw off. Category: Props
Needed a holder for nail e-file bits to go into a UV sterilizer - it couldn't be too big, and a tray would have blocked the light from the bottom part of the bits. I saw a few Dremel bit holders around, but all were too big/tall for this…
I designed this to hang my 15 watt UV sterilizer from the underside of the top of my custom, aquarium stand in the sump compartment. The sterilizer should fit snug into the semi-circular section and then use zip ties to fasten the…
In these hard times, wearing protective masks is vital. But we need much more masks than can be fabricated. So, it is a must to sterilize and reuse them dozens of times. The most affordable, effective and gentle method is using dry heat:…
Water Sterilizer Wall Mount for solving a little problem I had, where the sterilizer was supposed to be mounted on top of a cylinder I don't own, so I created a wall mount.
The power cable on the All American Sterilizer models 50X and 75X has no strain relief, and the cable experiences unnecessary wear at the cable grip. Print this piece out of TPU, wrap it around and secure it with 2-3 zip ties. During…
Cork needs to be printed with TPE not TPU , TPE is UV resistant and Ozone resistant while TPU is not. Materials: TPE - 85A - 1.75mm 3D Printer Filament 80ml Glass Test Tubes, 25×200mm Round Bottom Test Tubes USB 2.0 Female Pigtail Cable…
Description: These are risers for the Papablic Classic Sterilizer and Dryer, and I designed them because the large Dr Brown's bottles and Dr Brown's pitcher don't fit in the stock sterilizer. Not sure how common this product is, but if it…
A keychain holder / caddy for a UVC sterilization dongle. Should fit both USB-C and Lightning cable versions. Print this in a flexible filament. This is the product this fits:…
Meant for 5-8mm (ID) silicone tubing instead of 12mm. Best to be printed in black filament other than PLA. Because UVC will degrade it faster than you can spell biodegradable polylactic acid. Yeah you should probably use ASA
This is a Power supply mount for a JEBO UV Sterilizer Lamp that you can buy from Aliexpress or somewhere else.. The Wall thickness is 2.25mm. A 0.4mm Nozzle has a extrusuion with of 0.45, so 5x0.45mm = 2.25mm. If your slicer wants to…
The power cable on the All American Sterilizer models 50X and 75X has no strain relief, and the cable experiences unnecessary wear at the cable grip. Print this piece out of TPU, wrap it around and secure it with 2-3 zip ties. During…
