Counting matching models…
Gimbal protector for Radiomaster TX16S (MKI or MKII) / Jumper T16 radio (should work, not tested). Protector is from a one piece with a grip for easier removing. LED charging indicator is fully visible while the protection is on. Bigger…
This transmitter tray is designed specifically for the Radiomaster TX16S with a folding handle. All parts were printed in PETG for outdoor use: Satin sheet and Kores application 0.4mm nozzle 240C nozzle temp 90C bed temp 15% infill…
printed in PLA, probably could be printed in TPU as well. Try printing without support.
Gimbal protector for 10.5mm diameter gimbal stick
I didn't like any of the available Designs for Gimbal Protectors already uploaded on Thingiverse so I decided to design my own improved version. Some Key Features I found important: Both Gimbal Protectors connected in the middle, no…
What should've come with the radio... Features Fits both stock (10mm) and wider stick ends up to 16mm in diameter Full protection on toggles and dials Anti accidental power-on Customisable name plate area Recommended Print Settings…
Gimbals and Screen protector for Radiomaster TX12. Added - bridge between the Gimbals Guard - 2 x Antenna mount Recommend TPU-95A. PLA/PETG also works. No support needed
The wall mount is designed to keep the router securely in place, in my case in a camper van. Compared to the model I remixed this from, this mount uses much less material therefore prints much faster and is designed as a snap-on: a tab…
Joined gimbal covers for the Radiomaster TX16s radio. These are printed in PLA with a color stop part way. Black Hatchbox PLA: https://amzn.to/3sOiSnG Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution:…
My battery lid snapped at the hinge nubs. So I modeled this! It sits slightly below surface of controller for easy printing on a flat surface. To install, put one nub into the controller and bend the lid inwards so that the other nub can…
Hotswap 2.5" HDD/SSD caddy for old Fujitsu Primergy servers. Fits as a replacement for A3C40058356, see compatibility section for servers. Fits drives up to 12.5mm, however airflow might be an issue. You can use the metal piece from blank…
Did not like what I saw on thingiverse. 3D printers don't print very nice in the air, especially when you want ABS, HIPS, ASA, anything other than PLA, so I designed my own, where you can print it out of separate pieces and assemble it…
Protect gimbals and front sticks. New version with upper stick protection! Assembly the two parts with pressure, once in right position the upper part rotates freely. Insert the gimbal protection first, then rotate the other part: on the…
Gimbal Protector for the Radiomaster TX16S I have larger Gimbal Stick-Ends than the stock stick-ends. I wanted a Gimbal Protector that would fit over those but also fit in the Radiomaster TX16S case (the one that comes with the…
Quick mount mobile holder for the Radiomaster TX16s. Holds a mobile phone or similar (63 - apx. 90mm width) for use with Qgroundcontrol and Ardupilot or similar. Hardware: 1pcs apx. 60mm long 4.5mm (max 5mm) spring in tension. 1pcs…
!UPDATED!: V2 Radiomaster Tx16s Gimbal protector (also fits for AG01 gimbals) Combined and Single Version Perfect fit with all Materials. I used PLA Please like if you downloaded it :-)
I've been looking for a good box for my TX16S for some time. Either very expensive or just simple polystyrene. Here is my own box. Very easy to print, Rock Solid and Perfect Fit!!! I do not use the internal module. Therefore no fixed…
Yet another transmitter stick protector model! Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Doesn't Matter Supports: Yes Resolution: 0.2mm or better Infill: 5% - 10% Category: R/C Vehicles
Might look like the protector from the RM Boxer but is constructructed for the new RM TX15.
Sticks for TX16S M4 (no threads). Good grip for hybrid/pinch style. You are welcome to remix.
EdgeTX , a modified Firmware and a Radiomaster TX16 touch enabled screen make it possible for the FrSky Horus X12S radio transmitter to also have touch functionality. The increased thickness of the touch enabled screen though makes it…
This is my Pult Tray for Radiomaster TX16S transmitter. The parts named "Aloy_..." shall not be printed but rather made of Aluminium for best robustness. The Leather Applications are not required but make it comfortable and look…
I remix the original handle and put hole for screw and tightening nuts. Use a plug on one side of the handle for a good alignment
Die Pultbasis wird mit dem Rückteil des Senders verschraubt. Ich habe hierfür M3-Einschmelzmuttern in den Druckteilen verwendet. Der Sender muss zur Montage geöffnet werden (4 Schrauben hinten, 2 bei der Antenne) - Anleitung als…
Gimbal protector designed for the brand new Radiomaster TX16S MK3 . Tested and validated on the MAX version . This accessory helps protect your gimbals during transport and storage, preventing unwanted movement and potential damage. 📦…
For maximum strenght you should print it standing up with supports under the hooks
A very simple gimbal protector for the Radiomaster TX16S with holes big enough grand lotus stick ends Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No Supports: Yes Resolution: 200 Infill: 25 Filament: EcoJake PLA Doesn't…
Designed for printing in ABS @250C through a 0.4mm nozzle at 0.2mm layer height. Print with button face on print bed. Supports will be required for some areas, and finishing may be required on the retaining flanges due to the print angle…
This is a simple spacer to keep the 18650 battery holder from moving around and possibly damaging the power cables going into the radio If you ever plan on keeping your radio in your car I suggest you do not print this in PLA. I printed…
i disliked all the gimbal protections i found online so i designed this one…
A Remake of the original Radiomaster TX16s Battery Cover with TB Logo. Original Make credit to Radiomaster RC. Unable to make this as a remix due to link being unavailable currently. Hope you enjoy. https://techbytes.ca/3dprints/ IG:…
A spacer to keep the 5000 mah lithium-ion battery from banging around in the battery tray. This will keep everything locked in place.
proction pour inter Radiomaster tx15 tx15 max
Works for Fujitsu Primergy TX1320 M3. Tool-less installation of 2.5" drives. My print settings: 0.6 Nozzle 0.25 mm Layerheight Fill pattern: Rectilinear Fill density: 50% Brim type: Outer brim only Brim width: 2 mm The Model:…
A simple mount for Teltonika RutX11 router/modem with mounting holes. You have to print: InnerClamp OuterClamp The other two files are for those who want to modify Print Settings Printer: Kingroon KP3S Rafts: No Supports: No Resolution:…
My remix of the original grips, which are more ergonomic for my hands.
The device is designed to make it easier to hold the radio during flights. This makes flying your drone much more comfortable and takes the pressure off your hands. It has a folding mechanism that takes up almost no additional space when…
This is top plate to install SMA connector in TX16S. Best connector will be one with additional screws on side. For easy print top part is flat. Print requites support.
Si pierdes o se te rompe la tapa del modulo externo ya tienes repuesto.
Introducing the custom-designed GPU stand specifically crafted for the NVIDIA GeForce GTX 1060. This sleek and sturdy stand is the perfect solution for securely mounting your GPU, providing both stability and efficient cooling for optimal…
I wanted small wall hook for the radio, and could not find good alternative, so here is my own design. This wall mount was designed for CNC-upgrade handle, but should work with the original as well. Print Settings Printer Brand: Prusa…
Protective cover for Radiomaster TX15 sticks during carrying the remote outside the kit bag. Protector is mounted using the belt loop. Material: PET-G / PLA / ABS Supports: NO
remixed the original to make it stronger.
I really dislike the foam feel of RC car radios. I decided to design a replacement for the SLT3 used with my Arrma Typhon 3S. This part will fit any SLT3 transmitter, which comes on most all of Arrma's 3S line (Typhon, Granite, Senton,…
The tray its designed to be fixed to the M2.5 screw inserts includded in the case of the Radiomaster TX16 MK3, no modifications needs to be done to the transmitter; just print and add two M2.5 screws to fix the tray to the transmitter,…
addition for radiomaster TX16 and boxer switches
Para todos los que tenemos esta radio creo que es imprescicndible.
This is a clip to mount a Teltonika RUTX10 router on a wall, backboard, or other surface. Mount with the release tab facing up. PETG recommended for flex and heat resistance. I have not tested it with PLA, but PLA will probably work as…
You need also M4 Melt thread
Si pierdes o se te rompe la tapa de la bateria de la RadioMaster TX16s ya tienes de repuesto.
After fooling around with 5" and a whoop, I decided to build a 3". But what fun would it be to design my own frame? Well, it worked out awesome. The frame is a TrueX, 130mm motor to motor. Overall weight (including props, battery strap,…
Nozzle: 0.4mm Layer height: 0.2mm Material: PETG Supports only needed for 2.5 drives. Screws: 4pcs 6-32x6mm countresunk screw for 3.5" drives. 4pcs M3*5mm countersunk screws for 2.5" drives. You can print in place. After the successful…
Simple gimbal protector for easier carying in bag without need of using bulky case
This case is printable on a 220x220 bed, longest side is 218.5mm so it just fits. Printed in PETG, about 250-300g total with 2 walls and 15% infill. I realized there were no cases out there for the TX16S that I could find, part of that…
This is the gimbal protection remix designed because I have the x9d+ SE hall gimbals on my tx16s, and also wanted switch protection since I use a kwad bag. BIG THANKS TO: Tekniqueman with the original protection found here…
A bulky mount to hang your TX15 on a Skadis board, the file is tall because the radio seems to have a tendency to tip over, there are two versions, one with square bottom and one curved
Protects Radiomaster gimbal sticks with a diameter less than 8mm
This is a single-piece gimbal protector for the Radiomaster TX16S Mk II transmitter. It fits over the sticks and lightly clips into the neck strap fitting. The model prints well in either PLA or PETG with 5-10% infill and supports on the…
Inlay for the Radiomaster Large carry case to house the Radiomaster TX16s better then original. Suggested is to print it in TPU which will give a nice and soft protection. it has room enough for an external TX including its mounted…
Features Fits perfectly for anything with a GoPro mount Great overall stiffness to prevent shaky footage Fits nicely inside your carrying case for the radio Quick-release design - no need to unscrew all the way and have 2 loose screws!…
The Radiomaster TX16S with the folding stand is great. I am using the TBS Tracer module and the stand taps the bind button on the back of the radio and at times can be a little annoying. I also don't like the idea of the module being…
These are replacement "levers" for the sliders on the T16 and TX16S. Not being a fan of the short stock ones when using them for pan and tilt on my FPV planes, I wanted something longer. Andrew Newton posted a design for some thicker ones…
Insert and fixate (using superglue) a small stainless-steel/aluminium rod for the hinge-mechanism (only on the outer! hinge-parts). Be careful using the hinge – push the caddy completely in, before locking it. I tried to replicate the…
This is an under-cabinet mount for the Teltonika RUTX11 router. It simply snaps in place. I tried to design it to promote air flow and cooling. I'm not sure how hot this router can get and whether that might pose an issue for the mount's…
Fusion 360 file included! It's a magnetic mount for TX16S and Hawkeye 3.5inch FPV monitor Short demonstration video: https://youtu.be/c1FKlvVu_cY Printing: Open stl, split to objects/parts (there are 2 parts), orient as in photo and…
This model of the Terran Republic's TX1 Repeater has been split into parts for your convenient printing. The parts are intended to be glued together. That's all there is to it.
This was inspired by 'maltvat' https://www.thingiverse.com/thing:4681214 This is a new design not just a remix. The previous design by 'maltvat' does not always easily come out. This design has a bit more play and a little handle that you…
A tool to remove the nut from a Radiomaster TX16S switch. No idea how long it will last, but it works and gets the job done. Printed with 2 walls, with an alternating extra, 60 pct infill.
Repuesto de las Empuñaduras laterales RadioMaster TX16s.
capot avec ouverture sur le dessus pour : radiomaster tx16s
A simple plate for Radiomaster TX16S MKII that allows to remove stock antenna mounting if using only JR Bay as radio module.
Původní boční slidery mi zrovna moc nevyhovovaly. Vytvořil jsem tedy lehce delší verzi. Základní je o cca 2mm delší. Další verze jsou vždy o 1mm delší. Já používám tu základní verzi. Tisknuto z PETG. Tisk s podporami na podložce. Na…
Option 1: fujitsu_primergy_cage_fan.stl fujitsu_primergy_cage.stl Cage can carry 2x 3.5" HDD drives and 2x 2.5" HDD/SSD with caddy Required parts: 8x heat insert nuts (5x3x5mm) 8x M3x8 screw 70mm fan Option 2:…
Placa frontal superior RadioMaster TX16s
Wanted an LED headlight, did not want to pay for a bracket so I designed one, will need screws. Have tested with 2 different 5.75in headlights from a company called Braveway , unsure if it will fit other brands but it is likely. Tinkercad…
Remixed the 18650 case holder to fit Radiomaster TX15 radio. It should be printed with TPU filament.
No support required, just needs two M3 screws.
This is a remix of an already great design. I did not want to cut large holes in my case so I added M5 threads into the base of the handles to assist the glue in holding the handles on. I also created an alignment template (PDF) that can…
Rutx11 Mini Rack I designed a mini rack support for the Teltonika RUTX11. To fit correctly in the mini rack, I designed it to be 2U with a cable outlet. It is printed in PETG, 0.25 Draft, vertical with organic support. It can be printed…
This is the replacement Part for the TX16S Vibration Motor. It covers the hole motor and can be used with the standard screws. I drilled the holes with a 2mm drill. Print Settings Printer Brand: Prusa Printer: Prusa Clone Rafts: No…
Radiomaster TX16S antenna plate for a long range 8db 2.4 Ghz antenna. At the same time making the antenna removable in case you want to replace your stock antenna. I made it so that it's easy to print with a flat bottom. It wil take the…
La Crosse thermo humidity tx141th sensor shield cover. I printed the main body upside down with no supports on my Bambu Lab X1 Carbon printer.
A simple mount for Teltonika RutX14 router/modem with mounting holes. You have to print: InnerClamp OuterClamp The other two files are for those who want to modify Category: Office
Higher Lid for the RadioMaster TX16S - designed it, so I can use 26650 8000mAh LiIon batteries while my 5000mAh LiIon was not enough for multiple days on the flying field. If you need a different height, maybe for 4x18650, let me know and…
I got tired of having my battery move around inside the back cover of my radio, so I did something about it. This battery tray is specific to the aftermarket 3000mAh rectangle packs. It holds it securely in place but still allows for easy…
Removed the built-in antenna and top switches on my Radiomaster TX16s and needed to plug the holes. Printed in TPU. Category: Other
In the “because I can” category… When the stock fan on my Zotac 1070Ti Mini failed, I got a replacement from inRobert. It turns out I ordered a 1070Ti fan instead of a 1070Ti Mini fan. The only difference is that the diameter of one of…
Designed for the RUTX11. Required screws: 2x countersunk screw (4.5x25mm) Assembly included.
I was dissatisfied with all of the available models. They were either too complicated or did not fit the AG01 gimbals. So, I made my own version. The cups fit the AG01 with fully extended sticks. For the TX16s MKII, they can be connected…
V2 Hawkeye mount design with Fusion 360 files No supports and no brim needed Held by friction Requires 3pcs M3x12 (2 screws for TX16S and 1 screw for monitor) 3 slots in radio mount currently has no use but it's left in case later mounts…
Repuesto de los Empuñaduras traseras de la RadioMaster TX16s.
These 3d printable plates replace a stock part and limits joystick inputs to a particular shape. Each mask works on both the right and left sticks. The pictured example was printed from PETG with supports at 0.1mm layer height and 30%…
Although the RM TX16S Mk3 is a decent enough radio, the right and left slider levers are horrible. I use these as throttle for a F5J glider (and other gliders) and in case of quick response (during approach or low altitude) my finger…
Sometimes you just need a little reminder of what you programmed all the switches to do. This helps for a quick glance, especially as a pre-flight reminder. Print a few for your different configurations, or print one and swap out the…
The Mario 5 Support VTX TX1600 SpeedyBee (STL) is a 3D‑printed model designed to securely mount the SpeedyBee TX1600 video transmitter onto the Mario 5 drone frame, ensuring stable positioning, lightweight integration, and reliable…
https://github.com/manbehindthemadness/MavPi
Same print settings for the original cover, I added a strap mount holder so that I can strap my 3S LiPo to the TX 16S for using with my full crossfire module. Category: Replacement Parts
Radiomaster Tx16s Leg Rest for the CNC Handle version. Still easily removable. Super comfortable and the radio angle is good for your wrists. All credit to the original creator https://www.thingiverse.com/thing:4596611 Print Settings…
