Counting matching models…
Simple design to mount an inductive proximity sensor on your Elster V200 Watermeter. The sensor used is a “M12 DC 5V NPN NO LJ12A3-4-Z/BX-5V 300mA” sensor working on 5 volt. It triggers on the little red wheel in your watermeter and will…
Simple design to mount an inductive proximity sensor on your Elster V200 Watermeter. The sensor used is a “M18 DC 5V NPN NO LJ18A3-4-Z/BX-5V 300mA” sensor working on 5 volt. It triggers on the little red wheel in your watermeter and will…
Just a push fit attachment to give you a narrow aperture on the Sharks odd shaped handheld vacuum range, for getting into smaller area. Also included a particularly long one you can slice down to the size you want. No supports required.
The software that you need on the camera to recognize the count, may you install very easy with crome (ff is not working) on this site: https://jomjol.github.io/AI-on-the-edge-device/index.html
Model is designed with a 2.2 mm wall, to fit 5x0.4mm lines. Material: PETG Line Width: 0.4mm Wall Lines: 3 → no infill Flow Rate: 110% on my Snapmaker printer, I needed a little more material, otherwise the walls would separate Print the…
Simple design to mount an inductive proximity sensor on your Elster V200 Watermeter Type 8212. The sensor used is a “M18 DC 5V NPN NO LJ18A3-4-Z/BX-5V 300mA” sensor working on 5 volt. It triggers on the little red wheel in your watermeter…
Support to adapt the Gk7205V200 camera to an FPV test drone.
A film holder for an Epson Perfection V300 scanner. Needs minimal supports. Settings used to print were grid/snug to support just the overhang, 5% grid infill, and a .16mm layer height. Holds a 6-photo strip, and has a small catch…
I made this model to have a perfect fixed position for my water meter gateway sensor on my Elster/Honeywell v200 water meter. There comes a holder with the gateway but it is one size fits all and I found it hard to have it in the right…
Rat Rig V-Core 3 - Enclosure 2.0 side panel for electronic, this panel is not in the original package of panels for the Enclosore. If you use textured print sheet print one mirrored to get the textured side out.
Ratrig Elektronic back cover V200 files for print and lasercut
I bought the EV200Ds and I absolutely love them, out of 5 different pairs of goggles they are the only pair that comfortably fit my big head and wide IPD. They come with covers that go over for the front of the goggles but I really don't…
Shopping cart fixture for Samsung vehicle dock EE-V200SA. On the bottom it has insert in the same size as 1 EURO coin. It allows to unlock any shopping cart with open, horizontal coin socket. Simultaneously it allows to attach whole…
I bought the EV200Ds and I absolutely love them, out of 5 different pairs of goggles they are the only pair that comfortably fit my big head and wide IPD but I do not need two diversity receivers, I really don't need 4 antennas. The…
I picked up a Realacc RX5808 Pro Plus OSD Receiver and needed a cover for my Eachine Ev200D goggles so I designed one. I printed it at 0.15mm layer height with support. Infill does not matter. The receiver will be a real tight fit if you…
This is the OpenIPC VRX case model. It has been designed specifically for the Eachine EV200D goggles, with no consideration for other products' goggles. Since the goal was to achieve a compact size, a smaller BEC must be used to fit into…
Flat mount so you can move the interior light off the side near the door to somewhere else, just extend the 3 wires.
This is just a dump of some custom parts I designed for the Getac V200. I figured I'd dump them here before I ebay the computer itself. The handle requires 2x 1/4 in by 1 in screws and matching nuts. The handle mount requires 2x 12in x…
Sensor holder for KiWa/Honeywell water meter Made for M18 proximity sensor
A cover for the phone location of the SoundVision SV200W.
This gas cap is to allow you to attach an extended run fuel tank onto a Cat INV2000 inverter generator. The threading is made as M56x4.5. Since Fusion 360 lacks this thread in their tool, it was produced by creating the body as M56x5.5…
Convert the 7 optical drive bay covers into fan holders that match the external aesthetics of the case for the Lian-Li PC-V2000 Server Case (very old model, I'm a big fan of it). Some of the drive bays have a couple of notches sticking…
Just the case to run OpenIPC based FPV stuff check https://qczek.beyondrc.com/building-openipc-fvp-gears/
To mount this you'll need T-Nuts which can be found here: https://www.printables.com/model/228663-skadis-t-nuts-mounting-system-for-ikea-skadis-pegb
Multiboard compatible hanger for Dewalt DCW210/DCV200 20v sander. Mounting requires a “ 13mm Big Thread, Flat Head ” bolt. Model is published in onshape, here , for remixing.
