Counting matching models…
The VoronLightweightXCarriage by Vitalii3D 🥰 is a fantastic lightweight carriage for the Stealthburner but I was not happy with the existing cable management solution for a ClockWork 2 setup. So, time to make some parts. The Features A…
Please print from ABS or any other high temp material using official recommended Voron settings. A4T/XOL Mount
Hello, I noticed while using my Chaotic Labs carbon fiber tubes, the x-end stop piece for Vitalii3D Super LightWeight Carriage came up short. I made a part that will now ensure that the end stop will hit the end of the carriage. Also…
Update 11/2025: Updated the brace so it does not interfere with the Cartographer connector. Also made a few more cable management cutouts for more routing options. I was having a hard time getting consistent results from my Carto/Beacon…
When you use the Vitalii3D XOL/A4T Mount for Voron Printers it's possible that your Beacon/Carto is hitting the hotend. In my case it was the Trianglelab Dragon Ace Volcano where Beacon hits the sock/heater block. The hotend is also in…
I am using sensorless xy homing, so I wanted this improved/modified version without the endstop switch part.
I bought this cnc x carriage https://www.etsy.com/listing/1639526932/super-lightweight-carriage-for-voron because the dragon uhf made my plastic x carriage heat sets fall out due to the plastic mount softening up from the heat. I also…
I created this updated PUG mount for the newer double shear variant of Vitalii3D's Trident AB mounts. I used the original design idea here and integrated a few variants of the popular PUG design. It should slide right into place with some…
PZ Probe Mount I printed with typical Voron print settings in ABS. I did use supports on the face adjacent to the stepper motor - that side is not visible. Mount to carriage with M3x6 BHCS, and mount board using screws supplied with the…
Cable support for the Vitalii3D CNC EBB36 Mount, specifically for the EBB36 Gen 2 and Orbiter 2.5 configuration. I have designed it to be a very tight fit around the CNC Mount. Make sure the mount is pushed all the way into the plastic…
Uses 2 m5s, 3 m3s (one optional), and two m3 heated inserts. I've run this for 200 hours without issue. I use the secondary cable hole for a camera and the primary/PUG for my umbilical Model references the actual cnc design files from…
I like the vitalii3d XY joint, but the adapter for the end stop is out of date. I updated it to have a notch for the lip on the right joint as well as moving the holes to fit the hall effect endstop. I hope this helps others.
A cover for the Vitalii3D CNC Front Idlers that helps your Jabberwocky cutting arm compress fully to cut filament.
I have a trident, the Vitalii3D recommended mount makes the carto too far back and can hit the middle rear leadscrew. None of the other models I could find worked. So I created my own. y_offset: 22.5 I have two versions, one with just…
Printed mine in PCCF but I am sure ABS/ASA would be fine. After the first one melted from being too close to the hotend I just didn't want to risk it.
Modified version of the PCB Adapter for the VoronLightweightXCarriage
Bondtech INDX 1515 mount for Vitalii3D CNC Front Idlers.
This toolhead's MCU is a Fysetc H36 which uses the same mounting pattern as the EBB36 but has a preterminated cable that has no locking mechanism. I had problems with the cable coming loose and devised a quick, adjustable, easy to print…
I created this updated PUG mount for the newer double shear variant of Vitalii3D's Trident AB mounts. I used the original design idea here and integrated a few variants of the popular PUG design. It should slide right into place with some…
When you use the Vitalii3D XOL/A4T Mount for Voron Printers it's possible that your Beacon/Carto is hitting the hotend. In my case it was the Trianglelab Dragon Ace Volcano where Beacon hits the sock/heater block. The hotend is also in…
This toolhead's MCU is a Fysetc H36 which uses the same mounting pattern as the EBB36 but has a preterminated cable that has no locking mechanism. I had problems with the cable coming loose and devised a quick, adjustable, easy to print…
I am using sensorless xy homing, so I wanted this improved/modified version without the endstop switch part.
Uses 2 m5s, 3 m3s (one optional), and two m3 heated inserts. I've run this for 200 hours without issue. I use the secondary cable hole for a camera and the primary/PUG for my umbilical Model references the actual cnc design files from…
Hello, I noticed while using my Chaotic Labs carbon fiber tubes, the x-end stop piece for Vitalii3D Super LightWeight Carriage came up short. I made a part that will now ensure that the end stop will hit the end of the carriage. Also…
