Counting matching models…
Wrapping Paper Cutter Makes cutting paper for the holidays super easy and painless. Requires (1) #11 Exacto Blade -PLA works great -20% infill -may need support for the one overhand depending on your printer Credit for the model goes to…
Them : An AWG 22-24 wire wrapping tool will cost $29.95. Me : U MAD BRO? Best printed with 0.1mm layers. Feel free to remix - Add a longer handle or turn it into a hex bit. Scale it to fit different wire sizes.
Start slow, and speed up as needed. Can use sides to cut paper.
A wrapping paper holder that is stackable with a wall mount
Assembly instructions. Insert the blade from the front. Then tighten with the printed screw. Easy to print, easy to use. No screws are required to secure the blade. Use a new blade to avoid tearing the paper. Be careful when handling the…
To successfully craft this item, get the spring from the pen, on both sides, install the screw from the bottom, print 5 parts for the left side 2x stick 2Xroast 1xleft side/+2 cut springs, glue the springs to the underside of the roast.…
This Christmas wrapping helper lets you pre-cut 10 pieces of 4cm long tape to help with gift wrapping. You can fit two strips easily but you could probably do 3. I saw some collapsing tape dispensers out there but they use a ton filament.…
A Simple holder to store your Wrapping Paper. Its connectable so you can connect multiple holders. Its Designed to Print without support. But it has to Bridge the Connectors. Make Sure your Setup can do propre Bridging ore maybe use a bit…
Print Settings Printer brand: Bambulabs Printer: Bambu X1C Rafts: Yes Supports: Yes Resolution: 0.2 Infill: 25 Filament brand: Bambu Filament color: salmon Filament material: PLA Notes: glue with superglue
Na nůž jsem použil jeden díl z odlamovacího nože. Funguje dobře :-)
This is an easy print for storing your wrapping paper. The model stores up to 4 rolls. The model has a wide base so it dosen't tip over. The model has inserts in the bottom to prevent the paper from sliding around.
A bracket to holder a 25mm dowel through a wrapping paper or kraft paper roll.
A helper tool to keep your gift wrapping paper in place while wrapping gifts. This is the first version of the model, and it is not perfect. I plan to add a few more improvements to this model as I get them completed and tested,…
Made for 65mm rolls, if printed in PETG, this model is rather flexible and will accomodate multiple diameters. You also still can heat up the clamp and make it smaller as your spool diameter decreases. Thanks to the slot, you can unroll…
Wrapping Paper Cutter Makes cutting paper for the holidays super easy and painless. Requires (1) #11 Exacto Blade -PLA works great -20% infill -may need support for the one overhand depending on your printer Credit for the model goes to…
Please read the description to the end before downloading! This is a remix and redesign of the "Wrapping Paper Cutter, utility knife 2.0!", https://www.thingiverse.com/thing:5158937. I have a pack of 70mm long carpet knife blades, and I…
Them : An AWG 22-24 wire wrapping tool will cost $29.95. Me : U MAD BRO? Best printed with 0.1mm layers. Feel free to remix - Add a longer handle or turn it into a hex bit. Scale it to fit different wire sizes.
This text is ChatGPT generated, so cool. German version at the bottom. The perfect tool to easily and cleanly cut wrapping paper rolls! This 3D-printed accessory allows for precise cutting without the hassle of using scissors. Simply…
This is a small wrapping paper holder, designed to be clamped to a tabletop that will allow the paper to be drawn out flat and easily, making wrapping presents MUCH easier. Paper feeds under the lower post, which keeps it from rolling…
This is a more advanced wrapping paper station, designed to be clamped to a tabletop that will allow you to use multiple rolls of wrapping paper to be drawn out flat and easily, making wrapping presents MUCH simpler. Upper roll of paper…
This is a more advanced wrapping paper station, designed to be clamped to a tabletop that will allow you to use multiple rolls of wrapping paper to be drawn out flat and easily, making wrapping presents MUCH simpler. Upper roll of paper…
Here is a knife that I designed for cutting folded paper on a flat surface. So, you can use it to cut gift wrap or other paper to size on a table or floor. It's just the right sharpness to cut light paper and doesn't have a point so that…
Pin - to help secure wrapping paper to cardboard while taping Weight container with lid - to help weigh wrapping paper down, fill with any heavy material. Paper Bow template - draw around and cut out then fold together and stick, scale up…
Bring holiday cheer to your gift-wrapping station with this festive and functional paper cutter. This tool is designed to make cutting wrapping paper quick and easy, without the need for scissors or a knife, and while giving you a…
This is a wall mounted wrapping paper holder with screw holes, and you can make it bigger or smaller if you want. The screw holes are 2mm, but you can make them bigger or smaller.
This model is pretty self-explanatory, it is used to help keep your wrapping paper in place while unrolling it and so it doesn't roll away on you. Print Settings - Overture PLA -Place On The Side Face -10% Infill -3 Perimeters -0.3 Layer…
Transform your gift-wrapping experience with the Ultimate 3-in-1 Wrapping Paper Holder! 🛠🎁 This ingenious 3D model is designed to make your holiday or everyday wrapping tasks a breeze. It securely holds a roll of wrapping paper 🎄,…
DISCLAIMER The knife inserting system damages the blade apex and may make the paper difficult to cut. Please consider my Version 2 with a reworked knife inserting mechanism that does not involve touching the edge.…
Wrapping paper holder - right and left consoles two versions Scale it according your needs. I made screw holes blind so you may decide how to work with it more freely. If you need to use them, just drill a hole through or use self-tapping…
Simple solution to store Gift Wrapping Paper in a place where it doesn't take space away. A quick fix, nothing special. It ain't stupid if it works ;-) Printed with PLA.
Use 3 screws to mount 2 of these to the wall. Space based on your needs for wrapping paper.
Turn your ikea skadis desk into the ultimate wrapping station! This has been designed to fit a wide range of dimensions as well as widths! Print two off per roll. Best to print on the side with a tree support (the support is easily…
Start slow, and speed up as needed. Can use sides to cut paper.
Here are a few different sized clips that work great for keeping rolls of wrapping paper from coming undone into a big torn mess. Category: Organization
A wrapping paper holder that is stackable with a wall mount
After printing the model you will have two parts screw them each into the wall parallel to each other the same distance apart as your roll of wrapping paper. Put the wrapping paper in each hole and put the end through the slit.
Assembly instructions. Insert the blade from the front. Then tighten with the printed screw. Easy to print, easy to use. No screws are required to secure the blade. Use a new blade to avoid tearing the paper. Be careful when handling the…
This model has the advantage that the spacing between the prints can be much smaller than the length of the roll. It's therefore much more probable that you already have a scrap plank of the wanted length lying around. You can modify the…
This model is the perfect tool for cutting Christmas wrapping paper. It is a small pocket sized cutter that is less fiddly than scissors because it doesn't go under the wrapping paper. It can be printed in PLA and is very sharp so be…
To avoid the annual mayhem of wrapping presents use the Dromonem! Features box cutter/label peeler ribbon/wrapping paper cutter ribbon curler ruler folding/creasing edge sticky tape dispenser (rotating wheel and cutter) hardware (I am…
This holiday helper is the solution to a pet peeve of mine: runaway wrapping paper! We have all experienced it; if you try to just tug for more paper, the roll starts moving away! By setting it on these rollers, you can just pull upwards…
Use this gift organizer to keep your work area clean all the time. It includes tape holders, Pen holders and a cavity for whatever you need.
To successfully craft this item, get the spring from the pen, on both sides, install the screw from the bottom, print 5 parts for the left side 2x stick 2Xroast 1xleft side/+2 cut springs, glue the springs to the underside of the roast.…
A fleixble sleeve meant to keep your wrapping paper neat and tidy. I used the idea of HP but made it smaller to fit the rolls I had. Its only 30mm. I also made the walls thinner. There are small mouse ears in the model to help with…
The using indication can be seen in the photos. The parts aren't sticked together.
use a regular Stanley knife blade to insert, this is a first prototype so any other feedback or questions would be greatly appreciated. edit: V1 is not fully functional, i have made V2 which moves the blade forwards, and the angle of the…
Wanted the Blade cavity on the nut side and thinner cutter exit points. Can now print Half 2 upright for multi-color
This is a simple way to use a little bit of filament to keep the wrapping paper from running away. You will need a 1/2inch (12.7mm) dowel, broom handle, or PVC pipe for the round one holder. The rectangle one is for a yard or meter stick.…
This time made an gift wrapping paper and foil cutter. Design is easy to print couple of parts require supports I used tree supports as they are easier to remove. Device is designed to fit standard utility knife blade and perform straight…
this a wrapping paper cutter that i designt. you dom't need any kind of supports for it
This wrapping paper station holds three rolls of paper. It has a tape dispenser, a tool caddy, and the handle doubles as a straight edge cutting guide. The included tape dispenser has a 3D printed cutting edge that works okay, but it will…
This uses a a little more than a kg of filament, but the weight keeps it from falling over. It can be printed without supports. The lower portion prints right side up and the upper portion prints upside down. The holes on the upper…
Wrapping the 8mm extruder sleeve on my MK4S was already painful but the nervous breakdown came with the 5mm sleeve on the heatbed cables, hence a tool. How it works : (Photo 2) The cables are inserted in the central channel and the sleeve…
A square and a round wire wrapping mandrel. Both go from 25mm to 5mm in diameter in 2.5mm increments. Each tier is labeled with the diameter in millimeters. The handle can be removed when not in use, or glued in, whatever you like.
I wanted to disguise some gift cards the wife was giving this past Christmas. A way to wrap them without putting them in something like a box (but it looks like a box). I printed it in PETG because that's what I had loaded but it should…
Wire wrapping tool head for using with multi-bit driver handle. Category: Hand Tools
Christmas is allways around the corner!!! In search of potential helpers in the pre-Christmas period, I came across the great design by Rsojak https://www.thingiverse.com/thing:1984487 ! However, there were a few little things, such as a…
printed in pla on prusa mk4s (0.15 structural profile) infil 15.% adaptive cubic scarf seam on contours
This slip clutch uses magnetic coupling to maintain motor rotation. Hold the rod with your hand to break the coupling and slip the clutch to stop rotation so you can apply finish epoxy around critical fishing rod components. Additional…
Bring more order in your gift wrapping paper rolls! A holder for 23 gift wrapping paper rolls. The model consists of three parts: top part lower part bottom part You also need 4x round wood sticks with a diameter of 22 mm, 50 cm each.…
Small carrying case for a WSU-30 Wire Wrapping Tool with a holding bracket for a small amout of wire. Print settings: Material: PETG/PLA+/ABS Layer Height: 0.2mm Walls: 4 Infill: Grid/Gyroid, 15%
I made this to fit ASDA (UK) Just Essentials 60m wrapping film (Note: Cling film does not work, it has to be wrapping film) rather than buy the genuine Wrapmaster film as it is so much more expensive. Print using PETG ideally and use…
Got a friend of mine an LTT Screwdriver and wanted a more unique “wrapping” so I designed this cage for the screwdriver box where the recipient has to undo 26 M4x40mm bolts to get to the screwdriver. BOM: 26 M4x40mm Bolts You can go…
These have the same screw recess for mounting as Underware channels set up for “direct multiboard screw” mounting. Having individual/separate hooks allows for varying the spacing to accommodate the specific amount of excess cable and how…
This model is designed by me and was inspired by product called tape zoomie. it makes easy to pack multiple Gift/Product by dispensing tape.
Wall-mounted gift wrapping paper holder. For storing wrapping paper rolls, or similar light-weight, roll-like things. Maximum diameter per roll probably around 5cm. Mounted via two wooden screws of size 3. Included are versions for 2, 3,…
A wall mount for 30AWG wire wrapping wire with a wire guide so you don't have to hunt for the end of the wire. Print Settings Printer: Dream Maker Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.3 Infill: 20% Filament:…
Customized version of https://www.thingiverse.com/thing:2942689 Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing_id=2942689 Instructions Using the following options: $fn = 40 spool_radius = 35 spool_width =…
Tapered conical TPU wraps to hold the 0.25mm laminated carbon sheet cut to match the conical shape of to the Thrust Tube Former whilst joining it with a carbon cloth strip (I used a 6cm wide strip). As a tip, write down every sequence…
A cheerful and versatile design for all creative makers — these printable gift tags, decoration picks, and cake toppers can be used for wrapping, pastries, or table decoration. Each element can be customized with names, shapes, or small…
Furoshiki Patchin and Rings (風呂敷パチン) While furoshiki are often used without accessories, these models can elevate and modernize your experience! Patchin (パチン) Patchin are accessories designed to add a magnetic closure to your bag while…
based on a smaller version, these are for larger rolls of wrapping paper. One is for a 1 5/8" roll ( large ), and the other will accommodate 1 ¾" rolls ( larger ). the blade is slide into a channel, where it seats at the bottom. It is…
This Christmas wrapping helper lets you pre-cut 10 pieces of 4cm long tape to help with gift wrapping. You can fit two strips easily but you could probably do 3. I saw some collapsing tape dispensers out there but they use a ton filament.…
Turn your ironing board into a professional gift-wrapping station! These clever clip-on adapters are the perfect solution for keeping your wrapping paper rolls in place and maintaining order during holiday or birthday preparations. • Easy…
A Simple holder to store your Wrapping Paper. Its connectable so you can connect multiple holders. Its Designed to Print without support. But it has to Bridge the Connectors. Make Sure your Setup can do propre Bridging ore maybe use a bit…
My take on the wrapper holder/cutter. Designed from bottom up but not my original idea. This one is slimmer and more handy on the rolls i have come across. Being both thinner in diameter and wall thickness its also a bit cheaper to print…
This is a remix of the Wrapping Paper Cutter (X-Acto #11 Version) found here: https://www.thingiverse.com/thing:3226136 I loved the christmas tree one, so I wanted to do some other holiday shapes! Here are the files for a snowman, candy…
This is a customizable holder for keeping wrapping paper from uncurling when in storage. It's a mashup of the fine wrapping paper holder from Corey Brown ( http://www.thingiverse.com/thing:36166 ) and the Partial Rotate Extrude SCAD from…
Universal Monsters - Frankenstein - The Unwrapping - 1931 3D printable model.
About the Model Cuter that makes cutting those annoying sheets of Christmas gift paper rolls smoother and cleaner. Parts Design is based around a #11 Hobby Blade. Packs of a lot of these can be found on amazon for very cheap.
I bought a roll of multicolor Single-core wires from banggood. When I received the roll it was clear that I needed some way to prevent it from being a big mesh. And here it is. Fits a 70mm diameter roll, 33mm wide, 25mm inner core. Link…
Gift Wrapping Paper Roll Holder (Wall Mounted) Keep your gift wrapping paper organized and easy to access with this simple wall-mounted holder. This design securely holds multiple wrapping paper rolls above a door, inside a closet, or on…
Here is the minimal version with update for using two X-Acto blades. Category: Hand Tools
Another remix for a minimalist version. Still uses an X-ACTO #11 blade. Print Settings Rafts: Doesn't Matter Supports: No Category: Hand Tools
Remixed (from scratch) for a standard, X-ACTO #11 blade. See here for a minimal version... https://www.thingiverse.com/thing:3183256 Print Settings Printer Brand: XYZprinting Rafts: Doesn't Matter Supports: No Notes: Designed for 0.4mm…
This is a simple holder, notably my third thing printed at all in the hobby but its a simple holder for coin wrapping and sorting cups to keep them upright for use or storing. With the large center hole mostly for making it easier to…
Made a simple grip that prints in TPU that is glued onto a paper wrapping cutter (https://www.thingiverse.com/thing:3226136) to help make it more reliable and helps stop the paper from clumping up on the cutter.
This is the 3rd iteration of this cord wrapping widget for use with my kid's skadis technology ‘drop zone’ My goal was to make something that was easy and fun enough for them to use without my help. we will see how that goes… Print…
WHAT YOU NEED: 4 M3 x 8mm cap head screws; 4 M3 nuts; 1 regular razor blade ASSEMBLY: make sure all printed holes and countersinks are clear and free of strings, pressfit the nuts into the printed fittings (use a soldering iron if…
Flexible mount for split loom and wire wrapping for cable management. Mounts with 1x M3 screw. Diameter is 13.5 mm. Ideally part(s) should be printed in flexible filament and slowly to minimize stringing. Print Settings Printer: Custom…
Wrapping paper cutter with an ordinary Snap-Off Utility Knife (9 mm) Bring the paper cutter flush with the roll, gently press together so that the blade goes through the paper and simply pull (push) along the roll. The blade is easy to…
