1 / 8
Breezebuggy - a high performance ride-on play car for outdoor use — zdjęcie 1
1 / 8

Breezebuggy - a high performance ride-on play car for outdoor use

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A very capable play car! Powerful and fast with full suspension. The result of 3 years of testing and iteration.

Ocena
0 / 5
Polubienia
120
Wydruki
0
Wyświetlenia
5036
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Outdoor Toys
Licencja
Standard Digital File License

Intro

This is the Breezebuggy, a high performance ride-on outdoor use play car intended for children ~3-9years old. The car has been thoroughly tested and iterated upon to reach a high level of maturity in printing, assembly and use. The car is designed to be easy to build with a minimum amount of tools needed with the mindset to let the print-process do as much work as possible. The metal parts in the assembly are either off-the-shelf screws/bolts/etc or pieces of aluminum pipe or M-standard threaded rod. No welding or machining needed! The goal has been to create a high performance play car that is buildable by anyone with access to 3dprinters and some creativity, but without the need of a machine shop.

The breezebuggy is designed to utilize hoverboard motors and their fastening hardware, so a 36V hoverboard is recommended as donor vehicle. To drive the motors use ebike controllers, or reprogram the hoverboard mainboard. The body has built in hole patterns for both. Ebike controllers are easier to setup and requires less knowledge, but generally offers less customizability than a hoverboard mainboard. If you are new to ebike electrical systems it's easier to start with standard ebike parts. If you want to go the hoverboard mainboard route there is a good github repository called hoverboard firmware hack with a variant called hovercar. → Github repository

Note The github repository covers generation 1 hoverboard mainboards. There are also newer mainboards that are split up into separate controllers that aren't as well documented in reprogramming/flashing. Innoadditive creations can not provide support on these matters.

Due to the high performance it is important to use the car with caution and wear a helmet. Any build should aim to incorporate drive modes that allow for a slower and less powerful car when first starting out. This can be achieved with both the ebike controllers or the hoverboard electronics route.

The size of the car is 95cm long and 50cm wide. It is designed to fit two into a mid size station wagon car. Pictured a Skoda Ocatavia with two prototypes. The pictured prototypes are just under 24kg all up weight each.

Changelog

20260828 - Uploaded an updated rear half of the car. The rear damper has been moved to improve geometry under max damper stroke. The rear swingarms have been reworked to support this change. The load path through the rear half has been moved forward where the cross section is larger and stronger. The extra reinforcement bolt that was added has been removed as it is no longer necessary in the design.

Added comments in development changes in the instructions and updated BOM.

20260522 - Uploaded improved front mud guard models. A minor change to have less aggressive print angles.

20260515 - Uploaded updated verions of the front control arms. Changed tolerances for the axles that fasten the control arms to the body, and increased clearance for the anti squeak washers to allow more washer size variation for easier assembly.

20250820 - Uploaded new versions of the rear swingarms and both body halves. Further information in the iterations section in the instructions document. Removed no longer needed hardware from BOM.

20250305 - Added a design iterations section at the end of the assembly instructions. Uploaded new versions of the front and rear halves of the car with the latest improvements, see the iterations section for details. Updated instructions and BOM.

20250219 - Added a video of ice driving with studded tyres. 

20241028 - Updated the body halves to not require the reinforcement strips and glue step for assembly. Replaced with another pair of threaded rods and some printed hex pins for alignment. Instructions changed accordingly.

20241023 - Updated the TPU Nose file

20241017 - Updated the rear studded tyre files to make them easier to print (reduced buildangles)

20241010 - Changed front tyre size (from 220 to 240mm, uploaded new tyres with slightly lower tpu profile, updated rims and mudguards to the new size, uploaded stud-prepared tyres for winter riding, added the optional mudflaps that were missing

20241009 - Linked assembly instructions

Specs
  • Top speed 20-30+km/h depending on system voltage, motors and controller setup.

  • Drive modes for speed and power limits

  • Range is dependent of battery. If using the hoverboard battery, a healthy one should give 5-10km. Most prototypes have used custom 10s3p 18650 packs giving 20km+ range

  • Plug and play charging with the hoverboard charger

  • Full suspension

  • Enough ground clearance to be capable and comfortable to ride on rougher surfaces

  • Front and rear lights

  • Reverse (reprogrammed hoverboard electronics version)

  • (Optional) Cooling fan for the electronics inside the car

  • (Optional) Horn (If using a scooter headlight with built in horn)

 

Reasonable tool setup to build the car:
  • Electric drill and a standard setup of drills

  • Electric screwdriver and standard set of sockets for m6-m12

  • Angle grinder to cut some threaded rod and aluminum pipe

  • Some common hand-tools like deburring tool, pliers and screwdrivers

  • Soldering equipment and wire

 

Filament

The car will need about 12-14kg of filament in total. The body alone is close to 6kg with the density used in the prototypes. Most prototypes have been made out of Elegoo PLA at around 10€/kg, and the parts are designed to be strong enough with just PLA. The flexible parts of the car have been made out of Recreus filaflex 82A. This include damper bodies for the suspension, the seat, the nose and the 4 tyres. I recommend using this filament as it is of a suitable softness, fairly easy to print, available in 3kg rolls and being a cheaper alternative to ninjaflex. Harder flexibles like 95A will not work as well, but any flexible filament with suitable hardness can be used.

To print this car a 420x420x470+ mm build volume system is needed to fit the front body and the rear body halves. Systems like Elegoo neptune 3max, 4max, Anycubic kobra 2 max etc or bigger systems.

To print all the other components a 256mm cubed system can handle that. Bambulab P1P/P1S/A1 or similar.

Everything can be printed with a 0,4mm nozzle, but for the main body a 0,6mm or 0,8mm nozzle is recommended. Most TPU parts are advantageous to print with a larger nozzle like 0,6mm. For the rest 0,4mm is suitable.

 

Hardware

As this build requires many different bolts and other pieces of hardware, there is a bill of materials to be able to source all the needed parts. The design is made to utilize off the shelf hardware where it makes sense and contributes to the use experience, durability or ease of assembly.

(If there is interest) There might be a bulk-sourced hardware purchase alternative to make the sourcing easier for the individual maker. This would be a complete set of all the mechanical hardware needed that would result in much easier sourcing and a lower cost for the individual maker.

 

What you get

All stl files needed to print and build your own Breezebuggy

Print guide

Bill of needed materials → BOM and Print Guide

Assembly instructions → Instructions (under construction)

Access to further iterations/improvements to the design

 

Serviceability and ride stiffness

The Breezebuggy is the result of plenty of development and testing. Various prototypes have in total been driven for more than 500km and the components have been iterated to hold up to abuse. However mechanical failures can happen if crashes occur, and the car is designed to be easy to service. The most likely components to break are all easily accessible from the front/outside of the car.

The tpu-bodies intended for the dampers can be tuned depending on rider weight. The car is thoroughly tested with riders in the 15-30kg range, but has seen plenty of riding with higher loads as well. Riders between 95cm and 130cm fit well on the car. In the intro clip the riders are 122cm.

Remarks about the tpu body printing can be found in the printing tips document

 

Some handy design features of the Breezebuggy
  1. Front 3point fastening interface for accessories you might want to design yourself. (The decorative front B print has been discontinued)  My daughters have found it enjoyable to have a ride basket for plush toys, or a basket to put berries into when being out driving in the woods. Intended for m6 heat inserts

  2. Rear tube type fastening interface for attaching a visibility flag or a selfie stick. For urban driving together with parents the flag increases visibility and safety.

  3. Puller interface to be able to tow something (a stiff and hinged pull bar is necessary as the car has strong e-brakes) The soft puller also act as support to stand the car up vertically for storage.

  4. The seat is snap in place and allows access to the electronics inside without tools

 

About the performance
  1. The car is fast enough at 10s (36V system) to tag along basically any runner for training sessions. My daughters have been riding with me for runs stretching to over 10km. (6miles) With a 10s3p battery the car could likely do double that.

  2. It can traverse steep hills and grip is the limiting factor for climbing.

  3. As the electrical hardware is intended for moving up to 100kg uphill on a hoverboard, most use cases will have big margins on motor and controller load / heat with kids in the 15-25kg range.

  4. The body is designed to house anything from a standard hoverboard battery to custom 18650 batteries all the way up to 10s5p or even 12s5p. The general project focus has been to create a fun but safe solution that uses as much as possible of the donor vehicle. If maximum performance is desired, a 12s setup with moderate field weakening will do 40+km/h. However at these power levels the motors need to be monitored and possibly current limits implemented to avoid over heating.

 

 

Tagi