1 / 5
Kasa HD Indoor PTZ Outdoor Security Door Camera Cover — zdjęcie 1
1 / 5

Kasa HD Indoor PTZ Outdoor Security Door Camera Cover

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Kasa HD Indoor PTZ Camera housing to convert it for "light weather" handling.

Ocena
0 / 5
Polubienia
2
Pobrania
9
Wydruki
0
Wyświetlenia
223
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Photo & Video
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

This is a cover that I made for an extra camera I had. Let's face it, I want to buy the fancy Ring, but I have this extra gadget. My brain must make use of it, so why not? And I'd be more broke than I am if I bought EVERYTHING I “wanted.” Don't get me started on my Raspberry Pi plans… I digress… My urgency is nothing but laziness and sweet little neighborhood children that ring my doorbell if … anything… moves… near my house. J/K They're cool - but  excessive ringing is frustrating. There… NOW I am done digressing. #Bawk
 


This is not meant to protect against heavy weather, the camera I am using is indoor rated, and I am willing to assume the risks. My main worry will be condensation with rapid spring/fall swings. I am going to try it anyway. :) I have ideas for a desiccant and a proper “cover” to make a weather barrier. Since the Kasa was not designed for the angle I have it at (for the PTZ) it is limited but it has patrol modes, face following, “person alerts”, and night vision. It will work for a limited-range door cam! And nothing like a white item to show dust and how much I really need to wipe down the outer door frame. Oh well, add that to the list…

Items
 

 

What I did…
 

  • Feed the cord through reverse from the underside
  • Connect the device to the unpowered charging USB cable
  • Correctly position and set the camera into the base with the charging cable sling into the cutout
    • (Optional) Apply superglue to the base of the camera
    • I discovered that I did not need to glue in place
  • Connect the separate base piece and use 4 tiny screws on each side, I applied a small amount of sealant to the seal before screwing it together (low torque…)
  • I snaked the cable along the back grove lightly filled the hold and covered the cord with sealant
  • I placed the encased Kasa camera into position and screwed in the 3 weight bearing/mounting screws
    • Note, this is a “thin” design so torquing the screws too tight may “warp” the shape
    • I had to play with the tension when it interfered with my camera rotation
  • The additional plate goes between the wall and camera housing like a gasket. I applied a thin ring of sealant before screwing it in place.
  • I did file here and there to ensure the smoothest yet tightest fit

Some “Specs”

  • ~82 mm max base width
    • Since the “top” of the Kasa base rotates, I did have to cut out about 0.75mm for “spinning” clearance
  • ~117 mm max-height
  • “Interlocking” base sections
  • “Gasket” or “Cover” plate to seal the cord entry
  • Able to get a standard USB end into the base through the cord hole
  • I used 1X3mm screws for the side, you could go up in size a little - it's not weight bearing, more to close the “gap” between housing pieces
  • I used random long screws that I had but cut holes for ~4mm

Future Design Thoughts - Potential Remixes?

  1. The holes on the sides are small, and I could thicken the walls to make it more sturdy
  2. Insert / dessicant panel
  3. Dome / Cover
    1. Dust and water will be the end of electronics over time
    2. Considering PET cutouts - if someone has ideas, would love to know!
  4. The camera is 5V + many solar batteries are 5V - portable wifi camera
  5. Smooth out the design overall, a few “choppy” areas as I cut/molded it and designed it

 

I have printed this about 6 times to tweak little things here and there. Feedback is always welcomed. I am still learning Fusion, design, and printing :)

                                               THANK YOU AND HAPPY PRINTING

                                                                                          #Bawk

 

Tips always welcome

$ChickenCordon

Tagi