SV08 / Voron Style CPAP Mount and 120mm Exhaust Filter
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Adaptation of Nadirs top hat to mount a CPAP Fan and a filter with a larger fan than the stock 60mm, Voron Compatible
- Ocena
- 0 / 5
- Polubienia
- 21
- Pobrania
- 65
- Wydruki
- 0
- Wyświetlenia
- 911
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Printer Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial
This was a design with a few goals in mind - Mount a CPAP Fan to the Voron style exhaust filter insert used in Nadirs top hat for the SV08, intake fresh air from the exterior of the enclosure to improve part cooling when printing with PLA/PETG, quiet the CPAP fans' whiney motor and loud air intake as much as is reasonably possible using only printed parts, improve the exhaust filter design by using a much larger, quieter fan than the design suggested by Nadir, and reach these goals with parts that are relatively easy to print and assemble. This isn't necessarily a “pretty” set of parts, but it is functional and reaches the intended design goals. This is my first real CAD project, which I've taught to myself over the past couple of weeks, so things may not be perfect. The baffle design was loosely based off of a performance car muffler, and seems to function well enough. I had some help with certain areas from shoeys_for_newey, but this is 90% my work. If I made a mistake, if something doesn't line up, if tolerances need to be tighter or looser, let me know. It assembled fine for myself and @shoeys_for_newey.
This kit was designed around the motor, motor driver, and pwm adapter included with the BTT Universal Turbo kit. If you are using a different set of parts, your mileage may vary when it comes to mounting the electronics. I will confirm that the driver board from the Mellow CPAP fan kit uses the same mounting holes as the BTT kit, but is a slightly different board layout that doesn't sit flush due to the areas that the through hole components come stick out of. I'm including the STEP files of all parts in the upload so that you can modify them as you wish.
UPDATE 3/23/2025: Uploading new version of the CPAP Fan Mount, utilizing a larger block of TPU in place of the old “shroud gasket”. This does a better job at neutralizing some of the vibrations of the motor, and in turn makes the entire system quieter. Old parts will still be available, dumped into the “Old CPAP Mount” folder. BOM and directions are updated to reflect this change, if you intend to use the old version you will need different length bolts.
BOM:
10 M3 x 4mm long Heat Inserts, 4mm OD or larger
9 M3 x 3 mm long heat inserts, 5mm OD OR 9 M3 x 3mm long, 4.6mm OD
4 M3 x 22mm or Longer Bolts
5 M3 x 40mm Bolts
2 M3 x 6mm Bolts
4 M3 x 4mm or Longer Bolts
3 M2 x 5ishmm Bolts
8 6mm x 3mm Magnets
1 M10 bowden tube coupler
Some bowden tube
PRINTING/ASSEMBLY OF THE CPAP FAN MOUNT
The base of the CPAP fan was originally designed with M3x5x3 heat inserts in mind, but I realized they were difficult to find and unusual sizes, so I've included a version of the base with all heat insert holes modified to allow a more normal OD heat insert. I used M3x4.6x3mm heat inserts in the modified base. You will need 5 heat inserts to mount the Shroud/Baffle piece to the base, and 4 heat inserts on the back of the base to mount the nozzle piece and to allow you to mount the base to the top hat insert. Print the base flat using tree supports for the arm that mounts the CPAP fan and the interior of the duct. You may want to use support blockers for the heat insert holes on the bottom of the base.
There is a TPU block around the fan itself, and another TPU mount between the base and the CPAP fan. This is an attempt to separate the fan from the harder plastic and reduce vibrations/sound.
I printed the motor mount in 95a TPU, 1 wall, 2 bottom layers, 3 top layers, and 10% gyroid infill. Softer would be better here, so here's a reason to use that 90a or lower TPU you've been eyeing. I played with printing the motor mount in even softer configurations, including a heavy chamfer of the holes that the motor actually sit on (to reduce the effect of the wall), 0 walls, 0 top and bottom layers (only infill and walls), etc. Feel free to play with this a little bit.
The TPU Block was printed at 5 walls, top layers, 5 bottom layers, and 30% gyroid infill. Those settings were absolutely overkill, but the block itself needs to be fairly sturdy (and a bit of extra weight certainly won't hurt, being that the intention is to reduce vibrations).
The motor mount is technically directional - there is a “right” way to rotate it, and 2 ways that are very close to right but not quite. This was accidental, due to the CPAP fans mounting holes being different distances from each other and using those holes to create the gasket constraints. Use the 3 M2 bolts to mount the CPAP fan to the base from the underside, sandwiching the mount between the two parts. Reuse the self-tapping screws in the outlet of the CPAP fan to mount it to the arm.
The Shroud should be printed on the flat base. Supports are entirely optional - I printed without any.
Mount the Shroud/Baffle piece to the base, sandwiching the TPU block between them. Make sure to run the CPAP wire out the side of the block as you do so, before bolting things into place.
Mount and wire your electronics to the top of the shroud, and then place the magnetic top case on. This is only there to hide the electronics a bit, it is optional if you don't care.
PRINTING/ASSEMBLY OF THE FILTER
You shouldn't need supports for the interior of this, it was designed to support itself in the most difficult bridging areas. Screw your M10 bowden coupler into this knob. Use 2 M3 heat inserts on the bottom (for mounting to the top hat), 4 M3 heat inserts on top for mounting the lid, and 4 M3 heat inserts for mounting the 120mm fan. A 140mm fan with an adapter should also fit here, and feel free to adapt it to smaller fans if you for some reason want that. Screw the stock SV08 filament run out sensor in through the interior of the 120mm fan cutout before mounting the fan (assuming you intend to use it). Use foam carbon filters cut down to 65mm x 130mm for the interior. This is the same size that Nadir suggests for his filter, and I would assume fairly standard for this style of filter. You should be able to fit 6 or 7 inside this housing if you for want that many, the normal 5 is fine though.
UPDATE 11/21/2024 - Revised the routing of the bowden tube, revised the filter support pattern to improve printing, added self-supporting structure to the bowden coupler hole.
