1 / 11
Creality K1C Upgraded Rear Exhaust Fan (60mm to 120mm) — zdjęcie 1
1 / 11

Creality K1C Upgraded Rear Exhaust Fan (60mm to 120mm)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

The rear exhaust fan in the K1C is very loud and horrible pitch. This is a mod that allows to mount a full 120mm fan.

Ocena
5 / 5
Polubienia
80
Pobrania
277
Wydruki
3
Wyświetlenia
3933
Oceny
2

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

UPDATE:
I do not own the K1C anymore! I uploaded the .step file for this!
Consider buying me a coffee if you feel like it!
Cheers everyone :)

The rear exhaust fan on the K1C is so loud and the pitch is quite horrible so I decided to see if I could find a better fan (same performance but less noise or better pitch). 
I had done quite a bit of research and the only fan size that did NOT decrease the static pressure from the stock fan is a 120mmx25mm.

-Disclaimer: 

  • 4-pin fans, whether 12V or 24V, won't work well with DC controlled speed, which the K1C uses. To control fan speed, use a 2-pin or 3-pin fan. If you use a 12V fan, be sure to use a buck converter or similar to lower the voltage. 

  • I listed some good alternative 120mm fans at the bottom of the page.

-Chosen Fan:

  • Model: NF-F12 industrial PPC-24V-3000 SP IP67 PWM

  • Benefits: No modifications needed besides DIY cables. Better static pressure, speed, dB(A), and airflow than the stock fan. Allows for a closed chamber, reducing noise even when printing PLA.

-Performance Data (I do not have a lab, take these with a grain of salt):

  • Room level noise: 37.5 dB(A)

  • Stock Fan:

    • CFM with carbon filter: 12.5 CFM

    • Lid On: 54.2 dB(A) (measured 1m away at 100% speed)

    • Lid Off: 58.8 dB(A) (measured 1m away at 100% speed)

  • Noctua NF-F12 3000RPM 24V Fan:

    • CFM with carbon filter: 13.6 CFM

    • Lid On: 51.1 dB(A) (measured 1m away at 100% speed)

    • Lid Off: 54.7 dB(A) (measured 1m away at 100% speed)

**Data is from v23 of the stl model.

-Installation Notes:

  • Fan Mount: Use M3x4x4.2 threaded inserts.

  • Adapter Mounting: Use the same screw type as the stock fan but slightly shorter. An 18mm screw is recommended for mounting into the back panel.

-Good alternatives fans:

  • 12V:

    • ARCTIC P12 (3 pin - should keep DC speed control)

    • NF-F12 industrialPPC-2000 (3 pin - should keep DC speed control)

  • 24V:

    • NF-F12 industrial PPC-24V-3000 SP IP67 PWM (4PIN – will lose speed control)


❤ Enjoy this model? Your support means the world to me! 
If you love what I do, remember to like and rate the model. 
If you wish to further help me to fuel my projects, consider buying me a coffee,
I just do these for fun, but they take some time!
Every cup counts and is immensely valued. ☕ Cheers! 

Tagi