Wreality fan shroud for Creality K1 (5015, EBB42, Cartographer)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
I made a new fan duct for Creality K1 to allow use of alternative electronics
- Ocena
- 5 / 5
- Polubienia
- 28
- Pobrania
- 103
- Wydruki
- 0
- Wyświetlenia
- 1001
- Oceny
- 2
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Creality Parts & Upgrades
- Licencja
- GNU General Public License v3.0
Edit: You must remove the RGB, I2C, and PROBE pin headers on the EBB42 to fit the tested models. I desoldered the pin headers, but cutting them off with diagonal cutters is probably good enough.
I added an untested version of the x0 arm that has clearance for the three sets of pin headers mentioned above. I have not tested these models, so print at own risk.
It all started when I wanted to use a Cartographer on my Creality K1. I decided to replace the mainboard with a BTT Manta M5P. In the process of replacing the mainboard I ended up smoking the stock toolhead board.
The EBB42 sticks out a little further than the stock toolhead board sandwich, so I replaced the 4020 fan with a 5015 fan. I designed a set of parts that allows the use of an EBB42, a Cartographer, and a 5015 fan on the stock x-carriage.
Using the EBB42 allows the use of CAN. Since I am switched to CAN, I also ditched the cable chain and converted to loomed wiring. There are also a couple of lengths of weed whacker string in the loom to keep it “perky”.
There are four main parts:
- EBB42 mounting adapter
- "arm x0”, a mounting arm that attaches to the x-carriage closer to the x=0 position on the print bed
- "arm x220", a mounting arm that attaches to the x-carriage closer to the x=220 position on the print bed
- the fan duct with integral Cartographer mount
Print these as shown in the slicer picture. I recommend these print settings:
- 0.4mm nozzle
- 0.2mm layer height
- at least four walls
- at least 4 top and bottom solid layers
- organic (tree) supports
- supports on build plate only
You will need to supply:
- EBB42 or similar toolhead board with the PROBE, I2C, and RGB pin headers removed
- Cartographer assembled in the flat configuration (Beacon might also fit)
- 24V 5015 fan
- two short M4 heat inserts
- four short M3 heat inserts
- two M4x20 flat head screws
- four M3x8 socket head cap screws
- two M3x6 flat head screws
- two M3x20 flat head screws,
- two M3x25 flat head screws
I designed this to attach to the stock hardware in as many places as possible in an effort to maximize rigidity. This means the install must proceed in a particular order:
- Install the 3010 fan and the EBB42 mounting adapter using the M3x20 and M3x25 flat head screws. The arrow on the adapter should point up and the pegs should face out toward the front of the printer.
- Attach the Cartographer to the fan duct using the low-profile ("round head") screws that come with the Cartographer.
- Connect the EBB42 to all its devices. There isn't a lot of room, so keep the wires short. Do not install the M3x8 socket head cap screws yet.
- Attach the x0 and x220 arms using the coarse-threaded screws that used to attach the stock cable strain relief (top of the front of the toolhead) as well as the shortest pair of flat head M3 screws (one on each side of the toolhead). The EBB42 goes under the arms.
- Attach the arms and the EBB42 to the EBB42 mount adapter using the M3x8 socket head cap screws.
- Make a final inspection of the wiring. Make sure you can access the wiring that connects to the Cartographer.
- Use the pair of M4 flat head screws to attach the 5015 fan, the fan duct, and the Cartographer.
- Connect the Cartographer wiring.
The nozzle offset for the Cartographer sensor is:
- 36.4mm on y-axis
- 0mm on x-axis
- 2.8mm on z-axis
This would have been impossible without Henlor's amazing work to create CAD models of the Creality K1 stock parts. Inspiration also comes from tbkMaker's Skeletor fan duct for K1. This project originally started with trying to get that to fit with the EBB42.
Here is the Onshape CAD if you feel like you can help improve the fan duct.
