Keychron K8, K8 Pro, K8 Max or K8 HE in your own color
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
UPDATED April 2026 - All parts you need to customize, replace or repair on your Keychron K8, K8 Pro, K8 Max or K8 HE.
- Ocena
- 0 / 5
- Polubienia
- 2
- Pobrania
- 19
- Wydruki
- 0
- Wyświetlenia
- 216
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Computers
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
IMPORTANT UPDATE
Keychron has open-sourced their design files, you can get the model from their repository;
https://github.com/Keychron/Keychron-Keyboards-Hardware-Design
So you want a Keychron K8 Pro or Max in a color of your choice? Well you're in luck.
You will need 360 mm build width at least, so Prusa XL or Sovol SV08 Max etc.
Base case; you can get this from Keychron directly;
Information: https://www.keychron.com/pages/k8-user-manual-1
Direct Download: https://cdn.shopify.com/s/files/1/0059/0630/1017/files/K8_case.stp?v=1685152885
This is a K8 case, not a K8 pro; some standoffs are in the wrong spot, For K8 Pro, Max and HE, I added a remixed version. I cannot find any mention of any license for the model, so it is here until I am ordered to remove it.
Printing is a challenge, I ended up printing this with PLA support, bottom down, but I think it would be even better to print top-down with PLA snug “soluable” support. Yes, this takes a lot of PLA and you have to tweak settings to keep the PLA on the build plate… I ended up with a fix-her-up-er and used hotsnot to keep the bezels on ;P
I am contemplating a 3-part version to print with minimal support, but will require additional screws.
Big feet;
Small feet;
Modeled by myself, see files.
Bezels;
Modeled by myself, see files, i just scaled my https://www.printables.com/model/1167235-keychron-k2-he-trims-and-bezels to 348.5mm
Trims;
These are slightly different than the K2 ones. see files
Switch plate;
Using my old project https://www.printables.com/model/415721-prototype-3d-printed-hot-swap-mechanical-tkl-keybo, I created a plate that fits. The screw holes for the K8 version I modelled using the case, the Pro/Max/HE version I measured myself.
WARNING The plate 3D printed is very flexible, it's a challenge to assemble the keyboard without plate-foam. It will help if you have experience building keyboards.
The measurements taken to create the Pro/Max/HE case are reused for the creation of the plate.
Power/Mode switch, Mac/Win switch;
Available, but very fragile. Would suggest ABS or ASA, printed with soluble or non-stick material for supports. I have printed in PETG with PLA support, and with much care, it can be done. The latest version I printed was on the side, using regular organic detachable supports. They came out fine.
And to make things more complicated;
For a real K8 Pro, you need the “Replica K8 Pro Buttons”
For the original K8 keyboard, you need the “Modified Button”
Keycaps:
Use your own, or print some; I printed these;
https://www.printables.com/model/973476-full-mx-keycaps-set-ndeg3-iso-uk-fr-es-ansi-us
I remixed the Insert and Delete keycap to have the same font-size as the Home,End, Page up/Down. so it looks consistent., see; https://www.printables.com/model/1433848-remix-twisted-keycaps-no3-ins-and-del-smaller-font
Special considerations for the K8 Original keyboard.
The K8 (Original) has a single PCB, the 3 posts on the right hand side are a bit off, it's a tight fit. This is also the case in the original moulded case.
The stabilisers in the K8 are Plate mounted. I strongly suggest the enforced replacement plate, if the material of choice is flexible enough to fiddle the stabiliser-bar in. When printing in a very rigid material, or cutting from metal, use the one without the enforcement.
I modelled the buttons on the K8 Pro and adapted them for this case. They work perfectly in the replacement case, but they might not 100% fit an original case. Since these switches are quite hard to remove without breaking, I did NOT test the printed in the moulded case or vice-versa.
Special considerations for the K8 Pro, Max or HE keyboard.
I adapted the K8 case, so a moulded K8 PMH case WILL be different, but I have taken as much care as I could within TinkerCAD to make it fit the original keyboard parts.
I modelled the buttons on the K8 Pro, the K8 Pro, Max and HE share all plastics, plate and PCB layout, so the “Replica” buttons will fit a moulded case. The case here provided is adapted to fit the original plastics/parts/
Final note; I am now working on a replica PCB with hot-swap sockets. I am literally day-one in KiCad, so if anyone out there has a TKL PCB design with per key RGB, QMK/VIA compatible microcontroller and bluetooth and willing to share knowledge; please let me know :)