1 / 11
M16x1.5 Blind Stuffing + Nut and TPU-Sealing / M16x1.5 Blindstopfen + Mutter und TPU-Dichtung — zdjęcie 1
1 / 11

M16x1.5 Blind Stuffing + Nut and TPU-Sealing / M16x1.5 Blindstopfen + Mutter und TPU-Dichtung

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Wstępna wycena dla PETG

0,50 € – 0,61 € netto (bez VAT)

Dla pliku: M16x1.5_BlindStuffing+Nut_v01+Nut_v10_0.20mm_PETG_0.2mm_PETG#2_MK3SMMU2S_40m.gcode

To wstępna wycena jednego pliku. Dokładną cenę poznasz przed zamówieniem.

Plik i założenia wyceny

Plik użyty do wyceny

Średnia wycena orientacyjna: 0,56 € netto (środek widełek).

Masa podana przez autora
5 g
Czas druku podany przez autora
40,2 min
Materiał u źródła
PET
Materiał wyceny
PETG
Drukarka wyceny
Bambu Lab P1S - 0.4 nozzle
Proces wyceny
0.20mm Standard

Orientacyjna wycena wyłącznie wybranego pliku, oparta na masie i czasie druku podanych przez autora. Warianty plików nie są sumowane. Ostateczna cena zostanie obliczona po analizie pliku.

Zapisane na tym urządzeniu.

M16 blind stuffing to close unused openings for PG9 cable gland in housings (ca 16.0mm). Optional TPU-sealing available.

Ocena
5 / 5
Polubienia
20
Pobrania
238
Wydruki
1
Wyświetlenia
432
Oceny
1

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution — Noncommercial

M16x1.5 threaded blind stuffing to close unused M16-openings in housings.
Unused PG9-openings or PG11-openings in housings are also possible to close with this blind-stuffing set, but it is necessary to widen the opening in some cases (see details below).

[1] Thread type:
  Metric tread

[2] Diameters for suitable openings:
  Diameters for M16x1.5 opening:
  a) threaded hole:                    14.5mm / M16x1.5 thread
  b) drill hole without thread:  16.0mm / no thread
  Diameters for PG9 opening:
  a) threaded hole:                    13.9mm / PG thread -> Requires widening to 16.0 mm diameter.
  b) drill hole without thread:  >15.2mm / no thread -> Might require widening to 16.0 mm diameter.
  c)  For a PG9-opening you can also use 
      https://www.printables.com/model/1478855-pg9-blind-stuffing-nut-and-tpu-sealing-pg9-blindst
      as alternative.   
  Diameters for PG11 opening:
  a) threaded hole:                    17.3mm / PG thread
  b) drill hole without thread:  >18.6mm / no thread
  c)  For a PG11-opening you can also use 
     https://www.printables.com/model/1483396-pg11-blind-stuffing-nut-and-tpu-sealing-pg11-blind
      as alternative .                                                          

[3] Sealing:
  An optional TPU-sealing model file is available.

Print
Material:   PETG (blind stuffing, nut), TPU 95A (sealing)
Supports: not required
Brim:         not required
Serial printing (part by part) for better thread quality.

Assembly
Threaded opening:
Screw the blind stuffing into the M16x1.5 opening.
Optionally place sealing on stuffing before assembly.
Unthreaded opening:
Place blind stuffing in PG9/PG11/M16 opening and secure with M16x1.5 nut.
If necessary, widen the opening to >=16.0mm before assembly.
Optionally place sealing on stuffing before assembly.
Use a 1€ coin for turning of the blind stuffing.

Hint: 
Apply some silicone grease on the thread, so it can be easily be assembled and disassembled.
(Without grease, the thread tends to wind on and off somewhat “sticky”.)

Tagi