1 / 1
QIDI Q1 Pro Noctua 92mm Motherboard Fan 𖣘 - with Temperature Controlled PWM option! — zdjęcie 1

QIDI Q1 Pro Noctua 92mm Motherboard Fan 𖣘 - with Temperature Controlled PWM option!

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Replaces the small annoying stock fan with an offset 92mm (slim) fan for reduced noise and increased cooling capacity.

Ocena
0 / 5
Polubienia
6
Pobrania
19
Wydruki
1
Wyświetlenia
329
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Share Alike

This mod works best in conjunction with other mods to prevent overheating of the electronics and increase printing reliability. 


Connecting the fan

🔩 Parts

Minimum required parts:

  • Bolts:

    • 4x M3 x 20 mm Allen / Hex head - Mounting fan to adapter plate

    • 4x M3 x 25 mm Allen / Hex head - Mounting adapter plate

  • 2x Insulated ring terminals and pliers

  • Printed part:

    • Install with logo oriented to top-left (hidden when installed).

    • Small (black) zip-ties and cable-management might be helpful. 

Installing a 24V fan? Skip to the next section.

For a 5V or 12V fan you will have to source a Voltage Regulator to chop the voltage from the 24V power supply (PSU) down to 5V/12V.

There are several options available for purchase from the usual suspects.

  • Voltage Regulator options: 

    • 5V / 12V fan:

      • LM2596S DC-DC Step-Down Module / Buck Converter (affordable, efficient)

    • 12V fan:

      • Traco Power TSR 1-24120 (compact, efficient)

      • Linear Voltage Regulator, like the LM7812 (avoid, not efficient)

    • Other

  • Soldering iron and wire

(⚠) Warning: When using an adjustable Voltage regulator like the LM2596(S), check if the output voltage is at the correct level before connecting it to the fan!


⚡ Providing pixies

𖣘 "I have a 24V Fan"

Buy or make a 4-pin to 2-pin adapter and connect it to the original FAN2 output.
Or connect the 2 power wires, positive (V+) and ground (COM) using insulated ring terminals to the PSU's spare screw terminals.

Done, Bob's your aunty!


𖣘 "I have a 5V or 12V Fan"

Note: The preferred 24 Volt source is from spare screw terminals on the PSU. And most preferably connect wires using insulated ring terminals 🔎. As illustrated in the wiring schematic here.

A Silent / Low rpm fan generally only requires the power (+) and ground (−) to be connected to the fan (pinout). Other pins are left unconnected. 

🎚 See the next section if you find the fan being noisy when running at full speed. And wish to have fan speed dynamically adjust based on onboard temperature readings.

(⚠) Warning: Avoid tapping 5 Volt from the motherboard. People have reported that doing so causes the 5 Volt bus to drop too low and cause microcontroller unit (MCU) instability / failed prints.


🌡  Adding Temperature Control

Optional.

Since I had one lying around, I'm using the Noctua NF-A9x14 HS-PWM 92mm fan. It's... not terrible at 100% speed 🤔. Already way less annoying than the stock 40 mm fan.
But it's quite audible when the printer is idle 🌬
Hence why I opted to include temperature control.
Idle is nice and silent now 😌 

YMMV different model or brand fans might behave differently with this method.

Part 1 : The PWM Wire

All of the above and one additional connection.
Connect pin FAN2− on the motherboard to the PWM signal pin on the 4-pin connector of the PWM fan.
As shown in the wiring diagram.

Follow Part 2 to complete the setup.

(ℹ) "How does this work?"
This works because within a 4-pin PWM fan's circuitry the PWM signal is internally pulled up to 5V (see page 6 of the Noctua whitepaper). 
And the motherboard controls its fans (and heaters) by rapidly pulsing the negative pin.
Meaning, the MCU is then pulling down the fan's PWM signal to ground every time the hardware timer triggers.
Resulting in a PWM controlled fan, neat!


Part 2: Adjusting printer.cfg

(⚠) Backup your current printer.cfg file before editing the configuration. This way changes can be easily reverted.

We'll need to change some settings in order to control the fan using the stock software based PWM.
(Ideally we have access to hardware pwm, but alas, this is not working on the different outputs I've tried).

Open the printer.cfg file in the Fluidd dashboard via http://<ip-addres>/#/configure
Scroll down to the [controller_fan board_fan] configuration section, somewhere around line 364. Select this section with all its parameters and comment out the entire section (hotkey: CTRL+/).

Copy the following section and paste it directly below. Then click 🔃SAVE & RESTART to apply the changes.


[temperature_fan board_fan]
#pin: U_1:PC4 # Stock pin
pin: !U_1:PC4 # Inverted pin for 4-pin PWM fan
max_power: 1.0
shutdown_speed: 1.0
cycle_time: 0.01 
off_below: 0.0
sensor_type: temperature_host
control: pid
pid_deriv_time: 2.0
pid_Kp: 2
pid_Ki: 5
pid_Kd: 0.5
target_temp: 50
min_speed: 0.15
max_speed: 1.0
min_temp: 0
max_temp: 100

Plus 4 Community Wiki reference, and rabbit-hole...

Monitor the temperatures under load and adjust as needed.
I suggest to leave off_below at zero / disabled to prevent the fan from constantly starting and stopping and prolong its lifetime. Rather adjust the min_speed setting. Though, setting it too low and the fan will not spin up. No fan spin, no good.


📋 Pin-out

Source

Target

PSU V+

Voltage regulator IN+ / +Vin

PSU COM (GND)

Voltage regulator OUT− / GND

*Motherboard FAN2− (GND)

Fan Pin 4: PWM signal

NC (not connected)

Fan Pin 3: Tacho signal

Voltage regulator OUT+ / +Vout

Fan Pin 2: +12V input

Voltage regulator OUT− / GND

Fan Pin 1: Ground (GND)

*=Optional. (⚠) Requires additional changes to work properly.


Image source

Happy Printing,

Ghostcraft

Tagi