1 / 7
Big Bento - HEPA and carbon filtered exhaust for enclosed printers — zdjęcie 1
1 / 7

Big Bento - HEPA and carbon filtered exhaust for enclosed printers

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Inspired by the BentoBox, an all in one filter and exhaust for enclosed printers

Ocena
0 / 5
Polubienia
1
Pobrania
6
Wydruki
0
Wyświetlenia
174
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Accessories
Licencja
Creative Commons — Attribution

Introduction

Big Bento is a standalone combined exhaust fan and air scrubber. It hooks up to any enclosed 3D printer via a 100mm air duct, creating a slight negative air pressure in the enclosure, preventing fumes and VOCs from escaping through small cracks in the enclosure and instead being funneled through the scrubber.

The design is very much inspired by the original BentoBox scrubber with the stackable modules and the activated carbon cartridges, but the actual design is my own

Features

Easily accessible filters

HEPA filter cage uses a twist-lock design with 2 screw heads as pins riding in accompanying grooves in the housing. The handle can also be used to lift away the entire HEPA module to access the carbon below.

Carbon cartridges have a low profile hinged handle making lifting them from the scrubber easy

Small footprint

Since the base is designed to fit on a 256mm build plate, the total size of the full scrubber is 245mmx235mm footprint and 860mm tall

Quiet

Taking advantage of a large fan designed to move a lot of air, even with the resistance caused by the filters, the fan can remain at low - moderate RPM while still moving enough air.

I don't have a way to measure actual dBa but in practice it's quieter than the printer sitting next to it.

BOM

Note: Amazon links are non-affiliate, just pointing to what I used and what worked well

Item

Qty

Link

M3x5.7mm Heatset insert

10

M3x6 SHCS

6

M3x10 SHCS

4

40mm x 80mm x 15mm HEPA Filter

8

https://www.amazon.de/dp/B07K3TYGX3

Activated Carbon

~500g

https://www.amazon.de/dp/B095PZLXPQ

6mm x 3mm magnet

32*

https://www.amazon.de/dp/B0CMHNPYDX

4mm x 2mm magnet

48*

https://www.amazon.de/dp/B0CPS1JF3W

100mm hose

depends on placement

https://www.amazon.de/dp/B0D1GH7XM8

100mm hose clamp

4

https://www.amazon.de/dp/B0C249BXF9

100mm duct fan

1

https://www.amazon.de/dp/B0FD2K7XPW

Filament of choice

6kg

*Buy more than you actually need, they will come in handy later

Additionally, you'll need some CA glue, soldering iron and some common tools.

Printing

General

All parts were sized and their settings adjusted to fit within a 256mm³ build volume and to consume a maximum of 1kg of filament

All parts use gyroid infill unless otherwise specified.

Use a smooth or a satin build plate for good seal between modules.

If you're unsure about print settings feel free to check the included Orca Slicer project file.

Files follow the Voron nomenclature, i.e. [a]_ prefix for optional accent colors and filename_x[number] for multiples of the same piece

PLA is more than sufficient for all parts, I printed mine in mostly PLA-CF purely for the surface finish and PETG-GF for accent pieces because I had it on hand.

Housing

Since bulk of the filament will go here, I tweaked the settings to maximize the usage of each spool

File

Wall Loops

Infill %

Est. usage (PLA-CF)

Notes

Base_Lower

5

15%

958g

Supports enabled (Tree, Organic), Paint supports on the large overhang + top part of the curved exhaust duct

Base_Upper

4

10%

524g

Fan_Adapter

4

15%

442g

Support enabled (Regular), optionally add a modifier on the bottom part of the duct with bottom layer - concentric

Carbon_Housing

4

8%

976g

HEPA_Housing

5

15%

756g

Supports enabled (regular), paint supports on the underside of the 2 channels used for locking in the HEPA cage

Top_Duct_Adapter

5

15%

270g

Base_Vent_Cover

5

15%

50g

Good piece for an accent color

HEPA

Nothing special here

File

Wall Loops

Infill %

Est. usage (PLA-CF)

Notes

HEPA_Cage

4

15%

165g

Supports enabled (Tree, Organic), Paint supports on the large overhangs between the columns

HEPA_Cage_Handle

4

30%

27g

Good piece for an accent color

Carbon

File

Wall Loops

Infill %

Est. usage (PLA-CF)

Notes

Carbon_Cartridge_Top

4

15%

170g

Carbon_Cartridge_Bottom

4

15%

120g

Carbon_Cartridge_Mesh_Plate

8

20% HONEYCOMB (change density depending on the size of your carbon pellets)

7.5g

IMPORTANT: the actual mesh is generated in the slicer; set top and bottom layers to 0 and disable "Only one wall on top layer"

Carbon_Cartridge_Handle

8

15%

15g

Recommended to use a stiff material (like PLA / PLA-CF) because of the bending forces involved when lifting the carbon cartridge

Misc.

HEPA_Housing_Test - to test the fit and action of putting together the HEPA cage and the housing

Carbon scoop - a measuring scoop for the rough amount of activated carbon to go into each cell in the carbon cartridge

Assembly

Housing

Insert 6x3mm magnets into each corner

IMPORTANT NOTE: Magnets are a tight press fit, once they're in, they're not coming out without destroying the magnet or more likely, the part.

Magnet alignment tip - Use a part of the housing, insert 4 magnets facing the same way, then once they're in, add another magnet on top of each and use that as a template for the next part, that way, alignment is guaranteed.

Fan adapter - use a short length of 100mm hose and 2 hose clamps to secure the fan to the adapter

Optionally (and recommended), using superglue, glue together Base Lower and Base Upper

HEPA

Add 6x heatset inserts into the HEPA Cage, 4 at the top, 2 on the bottom ring, 1 on each side.

Screw in a M3x6 SHCS into each bottom insert to form pins using which the cage will lock into the housing

Screw on the handle with 4 M3x10 SHCS

Insert a filter into each slot

Carbon

Insert magnets into each half of both of the carbon cartridges

MPORTANT NOTE: Magnets are a tight press fit, once they're in, they're not coming out without destroying the magnet or more likely, the part.

Using CA glue, glue in all the mesh panels into the larger half of each of the cartridges

For the handle, install 2 heatset inserts into each and screw in 2 M3x6 SHCS

Once installed, the handle should with a little bit of bend snap into the 2 eyes on the carbon cartridge, if the handle is too stiff to bend, simply take out one of the screws and screw it back in through the eye of the cartridge.

For filling the activated carbon, the cells are designed to have an air gap in between each layer, they should be about 1/3rd full, give or take. The actual amount is not really important, as long as the distribution between the 2 cartridges is even.

Custom modules

I have included 2 STEP files, a blank face plate for the base for a custom design and a blank module with the top and bottom geometry and features. Feel free to go nuts with custom modules and designs.

Tagi