1 / 5
KTM 890 Adventure R High Fender Spacer — zdjęcie 1
1 / 5

KTM 890 Adventure R High Fender Spacer

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Fender spacer for use with 3" Cube Lights on 2023+ model KTM 890 Adventure R motorcycles.

Ocena
0 / 5
Polubienia
1
Pobrania
12
Wydruki
0
Wyświetlenia
115
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Automotive
Licencja
Creative Commons — Attribution — Share Alike

Hey all!

Quick model for dropping the high-fender from a 2023+ KTM 890 Adventure R enough to install 3" cube lights up an under the fairing.  I've included a taller version for 3" cubes (pictured), and a shorter version for smaller lights, or just to space the fender down a bit for whatever reason you may need to.

There are a few required parts for these -

Print material and settings -

  • Material: I highly recommend a material that's flexible while staying strong so it won't crack if the fender gets hit.  I used CF-ABS (specifically Siraya Tech Fibreheart ABS-CF Core - https://www.amazon.com/dp/B0DGQDPVVD)

  • Infill: 100%

  • Layer Height: 0.2mm

  • NO SUPPORTS!

Installing Heat-sets -

  • After printing, install the heat-set inserts with the soldering iron heat-set tool (using the M6 tip) - this will be pretty hard to do with 100% infill, and with as large as the heat-set inserts are.  I recommend using somewhere between 350C and 400C for the soldering iron to set the inserts if you're using the same CF-ABS filament.  I ended up using a large M6 washer to help ensure the heat-set inserts were fully seated and flat, but you can do this by hand.  Once all 4 heat-set inserts are installed, let the inserts cool before working on installing the part to the bike.

  • Optionally, install an M3x40mm (14mm spacer) or M3x50mm (24mm spacer) SHCS bolt into the small hole at the bottom for added strength.

Installing on Motorcycle -

  • Remove the fender's 4x bolts using a Torx 30 bit (these will be reused - set aside for now).

  • Using 2x M6-1.0x20mm SHCS bolts, loosely thread in the front / top bolts to the lower triple clamp.  Optionally, use a SMALL amount of Loctite 222 on the screw threads, making sure to NOT get any on the plastic part (Loctite will break down plastic - this is important!).

  • Using 2x M6-1.0x30mm SHCS bolts, loosely thread in the bottom bolts to the lower triple clamp.  Optionally, use a SMALL amount of Loctite 222 on the screw threads, making sure to NOT get any on the plastic part (Loctite will break down plastic - this is important!).

  • With all 4 bolts started, snug down to KTM-specified torque of 10Nm (~8lb/ft).  After torquing the first time, wait 1 minute and re-torque again (this will allow any compression of the plastic to settle a bit before the second/final torque).

  • Reinstall the fender reusing the original 4x Torx 30 bolts.  Snug down to KTM-specified torque of 10Nm (~8lb/ft).  Optionally, use a SMALL amount of Loctite 222 on the screw threads.

Tagi