KTM 890 Adventure R High Fender Spacer
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Fender spacer for use with 3" Cube Lights on 2023+ model KTM 890 Adventure R motorcycles.
- Rating
- 0 / 5
- Likes
- 1
- Downloads
- 12
- Makes
- 0
- Views
- 115
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Automotive
- License
- Creative Commons — Attribution — Share Alike
Hey all!
Quick model for dropping the high-fender from a 2023+ KTM 890 Adventure R enough to install 3" cube lights up an under the fairing. I've included a taller version for 3" cubes (pictured), and a shorter version for smaller lights, or just to space the fender down a bit for whatever reason you may need to.
There are a few required parts for these -
M6-1.0 Heat-set inserts (Long) - https://www.amazon.com/dp/B077P9BG87
Soldering iron for installing the heat-set inserts (if you don't have one already) - https://www.amazon.com/dp/B0CJR4Y192
M6-1.0 20mm and 30mm (24mm spacer-only) 304 Stainless SHCS Bolts - https://www.amazon.com/dp/B0895NN4RT (assorted kit with both sizes needed)
Optional: Low-strength Loctite (purple, not blue or red) - https://www.amazon.com/dp/B0002KKTT0
Optional: M3x40mm (14mm spacer) or M3x50mm (24mm spacer) SHCS Bolt for added strength - https://www.amazon.com/dp/B07RRGKZLM (assorted kit with both sizes needed)
Print material and settings -
Material: I highly recommend a material that's flexible while staying strong so it won't crack if the fender gets hit. I used CF-ABS (specifically Siraya Tech Fibreheart ABS-CF Core - https://www.amazon.com/dp/B0DGQDPVVD)
Infill: 100%
Layer Height: 0.2mm
NO SUPPORTS!
Installing Heat-sets -
After printing, install the heat-set inserts with the soldering iron heat-set tool (using the M6 tip) - this will be pretty hard to do with 100% infill, and with as large as the heat-set inserts are. I recommend using somewhere between 350C and 400C for the soldering iron to set the inserts if you're using the same CF-ABS filament. I ended up using a large M6 washer to help ensure the heat-set inserts were fully seated and flat, but you can do this by hand. Once all 4 heat-set inserts are installed, let the inserts cool before working on installing the part to the bike.
Optionally, install an M3x40mm (14mm spacer) or M3x50mm (24mm spacer) SHCS bolt into the small hole at the bottom for added strength.
Installing on Motorcycle -
Remove the fender's 4x bolts using a Torx 30 bit (these will be reused - set aside for now).
Using 2x M6-1.0x20mm SHCS bolts, loosely thread in the front / top bolts to the lower triple clamp. Optionally, use a SMALL amount of Loctite 222 on the screw threads, making sure to NOT get any on the plastic part (Loctite will break down plastic - this is important!).
Using 2x M6-1.0x30mm SHCS bolts, loosely thread in the bottom bolts to the lower triple clamp. Optionally, use a SMALL amount of Loctite 222 on the screw threads, making sure to NOT get any on the plastic part (Loctite will break down plastic - this is important!).
With all 4 bolts started, snug down to KTM-specified torque of 10Nm (~8lb/ft). After torquing the first time, wait 1 minute and re-torque again (this will allow any compression of the plastic to settle a bit before the second/final torque).
Reinstall the fender reusing the original 4x Torx 30 bolts. Snug down to KTM-specified torque of 10Nm (~8lb/ft). Optionally, use a SMALL amount of Loctite 222 on the screw threads.