Synchronized Gear Extruder (HGX, PSF, Stealh-ProtoXtruder, Filament Sync)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Combined and modified some awesome models to build a single filament sync extruder. A single modern MMU lane.
- Ocena
- 0 / 5
- Polubienia
- 10
- Pobrania
- 12
- Wydruki
- 0
- Wyświetlenia
- 287
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Printer Parts & Upgrades
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Motivation
I started this project because I sometimes had issues with too much friction in my PTFE filament tube on my Voron 2.4. People with an MMU/AMS system don't have to worry about these problems. I've been having some issues with FLEX filaments recently. I've been getting underextrusions and inconsistent print results. I figured out that what I need is basically a gate from a HappyHare MMU Driver, and that I already have the right software for Klipper.
Features
Consistent Flow Rate (Proportional-Sync-Feedback-Sensor (PSF))
Clog Detection
Tangle Detection
Filament Load/Unload automatism
Add a 2020 profile mount (works great for Voron)
You could also build more instances of this if you wanted to create a basic MMU system.
Reusability and further remixes
The optimized (Stealth-)ProtoXtruder with tuned filament sensors can be used independently, as the original
The adapted PSF may be screwed to a completely other model
Extruder and Filament Sync Sensor could be replaced completely
Build
Extruder
The ProtoXtruder 2.0 is a large, dual gear extruder. These large gears have, in theory, the best and most consistent filament extrusion on the market. It uses not the Bondtech LGX gears, but the cheaper (and more slim) HGX 2.0 Lite gears. My adapted version here uses a gear set and a Filametix set (includes the 2x Omron D2F switches and the 5.5mm steel balls). Of course, you can source the parts individually. I recommend my adapted version here because I had issues with the remixed mod. The sensors did not work well because of their distances, and the front part was not so nice to print. But, feel free to experiment.
Find further descriptions on the original models I remixed from. And an explicit "thank you" to both guys: @nhchiu and @_387905 for providing these models.
Proportional Sync Feedback Sensor (PSF)
This kind of sync feedback sensor is the best solution you can currently have for a happy hare based Synchronized Gear Extruder. Please follow the HappyHare instructions and the instructions from the creator. To make the system work you have to configure the system in HappyHare as a Custom Type-B MMU with just 1 Lane/Gate.
Use my remixed model here. Together with the 2020 Mount, I removed one of the ECAS PTFE Tube connectors and attached instead directly to the mount. Without this modification, and after some stallguard ramming to the extruder, the ECAS pushed out itself again and again. Besides of that, it just not needed in this combination, it's more stable and less error prone. BTW, the sensor is working in both directions, so don't care if the arrows point upwards.
Sorry I didn't position one of the two screws better. I plan to completely rework the whole thing from scratch, but until then, it is what it is. :-)
Find further descriptions on the original models I remixed from. And an explicit "thank you" to both guys: @kashine6 and @ningpj for providing these models.
2020 profile mount
A simple and easy to print part to bond the extruder and the sensor together an attach it to any 2020 extrusion (like my frame of the Voron). Feel free to mirror it in the slicer, if you need in on another side. There is a cutout on the back for a cable tie.
While you're screwing the sensor and extruder onto the mount, I'd recommend threading a piece of filament through both to make sure the filament guide is working properly.
BOM
Extruder
HGX Lite 2.0 Gear Kit (on AliExpress)
NEMA 14 stepper
1x M3x20 SHSC
3x M3x16 SHSC
3x M3x6 BHSC
2x OMRON D2F switches (part of Filametix Set on AliExpress)
2x 5.5mm steel balls (part of Filametix Set on AliExpress)
Curled Brass Inserts M3x4 and M3x3
Proportional Sync Feedback Sensor (PSF)
Get a sensor electronic set from Aliexpress or build one yourself follow the original instructions
2x M3x8 SHSC (for mounting)
2020 profile mount
2x M3x20 SHSC for the extruder
2x M3x8 SHCS for the sensor
2x M3x10 SHCS for the 2020 profile
2x M3 T-Nuts
Love my 3D models?
If my designs have helped you print something awesome or inspired your next project, consider supporting my work! Your kindness fuels my creativity, keeps the filament rolling, and helps me share even more free/pay-what-you-want models in the future. Every coffee counts!
Disclaimer: Use this mod at your own risk. I am not responsible for any damage to your printer or any consequential damages resulting from improper assembly or use. This is a personal design project.